SIIG CE-KV0G11-S1 2-Port 4K HDMI KVM Switch with PBP Roaming Mouse and PIP User Manual
- June 9, 2024
- SIIG
Table of Contents
CE-KV0G11-S1 2-Port 4K HDMI KVM Switch with PBP Roaming Mouse and PIP
User Manual
Features
-
Supports Video Scaler & PIP/PBP Video Mixer Up to 4K@30Hz (4:4:4)
The Display Must Support Top-Bottom or Left-Right PBP function. -
Unique Full-Frame PBP doesn’t sacrifice any display area for PBP
-
Image stays unstretched in PBP Modes
-
Zero-Latency Swap between PIP & Full-Screen Mode
-
User Can Adjust PIP Images’ Size/Location/Transparency
-
8 sets of users presets for fast configuration
-
HDCP 1.4 Compliant
-
4K Scaler Function Ensure Pixel-to-Pixel Matching for Most Displays
-
3 Ways Control Methods for Easy Selection :
Front Panel Push Buttons
Hotkey Control
Roaming Mouse Switch -
Keyboard & Mouse Plug-n-Play, No Software & Drivers Required
-
Support Windows/Linux
-
Support 3.5mm Audio & HDMI Audio
Package Contents
- 2-Port 4K HDMI GM Switch with PBP Roaming Mouse & PIP
- Power Adapter 12V/1.5A
- User manual
Layout
Front Panel
- USB HID console port (for keyboard & mouse use only)
- USB 3.0 port at console for USB peripherals 5Gbps, 5V/900mA,
- Link: Green, connected PC is power on Select: Red, connected PC is selected
- Switch Button: Press to select PC
Rear Panel
-
Power Jack: DC 12V/1.5A (support DC 9V-12V, 1.5A)
-
USB HID console ports (for keyboard & mouse use only)
-
HDMI output: resolution up to 4K@30Hz
-
Speaker/Earphone port at console connect to Speaker/Earphone
-
PC-x input ports:
HDMI input for PC-x
USB 3.0 Type-B port for PC-x
Speaker/Earphone port for PC-x -
USB 3.0 port at console for peripherals 5Gbps, 5V/900mA
Hotkey Control
Hotkey Leading Codes ( HK_LCode )
A Hotkey command is a short keyboard sequence for selecting a computer,
activating computer scan, etc. KVM Switch interprets keystrokes for hotkeys
all the time. A hotkey sequence starts with HK_LCode followed by one or two
more keystrokes. A built in buzzer generates a high-pitch beep for correct
hotkey command; otherwise, one low-pitch beep generates for error and the bad
key sequence will not be forwarded to the selected computer.
HK LCode can be
“L-Ctrl”+”L-Ctrl” or “Scroll Lock” + “Scroll Lock”
Must be use below keys on keyboard to input Hot-key, especially number keys
and “L-Ctrl”. Left and right are different command for the hot-key.
PBP Modes (Mode 1& 2)
PBP Modes
Top-Bottom PBP (Mode 1)
Left-Right PBP (Mode 2)
*Change last letter can use different resolution output
Vertical (Mode 2)
- The KVM sends Proper EDID to both source.
- The Display Must Support Top-Bottom or Left-Right PBP function.
Full Screen & PIP Modes (Mode 0&7)
Full Screen (Mode 0)
PIP (Mode 7)
Swap
- User can copy EDID from display.
- Roaming Mouse Disabled in mode O & 7
- Change last letter can use different resolution output
- Switch between modes or resolutions might take 10-12 seconds or more depend on display’s response time.
- letter R,H,G,O are special up-scaled outputs as follows
R: Input=2560×1440@60Hz & Up-scaled to 3840×2160@30Hz output
H: Input=19201080@60Hz & Up-scaled to 3840×2160@30Hz output
G: lnput=1920×1080@60Hz & Up-scaled to 2560×1440@60Hz output
O: lnput=2560×10800@60Hz & Up-scaled to 3440×1440@30Hz output
This Video Up-Scaling Function Is Specially Useful for Source Compatibility or
KVM Extender Compatibility.
For Example:
- Source Is Capable of Only 1080p Output
- Source Is Placed 1 S0M away & Requires Long Reach Function of HDBaseT Extension (1080p) In Such Cases, The Scaled Output Can Improve Image Clarity on Modern Hi-Resolution Displays.
** Switching between screen layout modes might require image fine-tuning
(User can save fine-tunned setting to user’s presets)
PIP Location Control
Main Screen Size Control
PIP Size Control
PIP Transparency Control
Other control
Basic Hotkey Control
Mouse Roaming
Advanced Operation
3. Image Fine-Tuning
If the image engine doesn’t work properly, image re-synchronization should be
proceed to resume normal operation
Video Compensation Adjustment
In different resolution & layouts, there might be slight difference in
compensation requirement which might result in image flicker. Adjust video
compensation can greatly improve image quality under such circumstances.
User’s Presets
User can restore up to 8 presets.
Dear Valued Customer
WE REALLY APPRECIATE YOUR PURCHASE
∼thank you
Support
For more info or tech support
http://www.siig.com/support
Sep, 2022 Copyright 0 2022 by SIIG, Inc. All rights reserved.
04-1383B
P/N: CE-KV0G11-S1
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>