TIETI B-2 Spirit Mini Wireless Mechanical Gaming Keyboard User Guide

TIETI B-2 Spirit Mini Wireless Mechanical Gaming Keyboard User Guide

GETTIGN TO KNOW YOUR KEYBOARD

BEFORE FIRST USE
Charge the keyboard fully before first use by connecting the USB cable to the keyboard USB Type-C port.
CHARGING & BATTERY LIFE
The keyboard will indicate charging status when connected with PC.

Using the check battery life shoutcut below, an indication will play to denote current battery charge level.

FN+Enter

|

Check Battery Charge Level

|  Key “1” Solid Red| 10% charged
Key “‘I” &”2″ Solid Red| 20% charged
Key “1” & “2” & “3” Solid Red| 30% charged
Key “1” & “2” & “3” & “4” Solid Yellow| 40% charged
Key “1” & “2” & “3” & “4” & “5” Solid Yellow| 50% charged
Key “1” & “2” & “3” & “4” & “5” & “6” Solid Yellow|  60% charged
Key “1” & “2” & “3” & “4” & “5” & “6” & “7” Solid Yellow|  70% charged
Key “‘I” & “2” & “3” & “4” & “5” & “6” & “7” & “8” Solid Green| 80% charged
Key “1” & “2” & “3” & “4” & “5” & “6” & “7” & “8” & “9” Solid Green|  90% charged
Key “‘I” & “2” & “3” & “4” & “5” & “6” & “7” & “8” & “9” & “0” Solid Green| 100% charged

RESET TO FACTORY DEFAULTS
Press and Hold the key “FN” and “CAPS” together for 3 seconds then release, the keyboard will be reset to factory default settings.
CONNECTING VIA 2.4G WIRELESS

1. Plug in the 2.4G receiver to PC USB port
2. Slide the keyboard power switch button to the 2.4G position
3. The keyboard will connect to PC automatically.
   Note 1: If the nano wireless adaptor lost pairing with PC, or an unused nano wireless adaptor need be connected, repeat the above step 1 and 2, press and hold key “FN” and “H” together for at least 3 seconds, key “H” will start quick flashing green, after successfully paired, it will turn to solid green for 3 seconds then off.

Note 2: If key “H” keeps flashing green for 1 minute but still not paired, the keyboard will go to sleep mode and flashing will be off. You need enter a random key to wake up the keyboard, then retry the steps listed in Note 1.

CONNECTING VIA BLUETOOTH WIRELESS

1. Initiate Bluetooth pairing on the host device such as PC or phone
2. Slide the keyboard power switch button to the BT position
3. Press and hold “FN” and “J” or “K” or “L” for at least 3 seconds, key “J” or “K” or “L” will start quick flashing green, after successfully paired, it will turn to solid green for 3 seconds then off.
   Note : If key “J” or “K” or “L” keeps flashing green for 1 minute but still not paired, the keyboard will go to sleep mode and flashing will be off. You need enter a random key to wake up the keyboard, then retry the above steps.

CONNECTING VIA USB CABLE

1. Connect the keyboard via USB cable to a USB Type-A port on PC
2. The keyboard will automatically switch to USB wired mode.
   SOFTWARE MODE
   Welcome to visit TIETI’s website www.tieti-tech.com/download and download the software TIETI Synapse for installation, you can control everything of the keyboard from lighting to powerful macros.

SWAPPING KEYSWITCHES

The keyswitches can be removed and replaced with any variety or combination of CHERRY MX RGB mechanical keyswitches. Other third party mechanical keyswitches with 3-pin design may be compatible, but are not guaranteed to work due to physical differences.

1.Push the side for keycap of the 2-IN-1 PULLER over the keycap, then lift to remove

2.Position the tips of the keyswitch puller under the keyswitch top and bottom tabs, then press in and lift to remove

3.Align the new keyswitch’s pins and base with the sockets and opening.

4.Carefully press the keyswitch in until it c icks into place. If you feel any resistance, remove and try again.

PROFILE & LOCK FUNCTIONS

LIGHTING SETTING

Green,Cyan, Blue, Purple, White
FN + <| Shift RGB lighting mode (from end to start)
FN + >| Shift RGB lighting mode (from start to end)

Total 22 modes are available as below, including the last 3 modes which are provided in software mode.

1. Static color
2. Dynamic Breathing
3. Color Shift
4. Rainbow Wave
5. Rainbow Ripple
6. Stars Twinkling
7. Streaming
8. Type Lighting
9. Flapping
10. Sine Waving
11. Surging
12. Blooming
13. Lasing
14. Color Waterfall
15. Inclined Rain
16. Raining
17. Streaming line
18. Type pulsing
19. Customization mode
20. Music mode (EDM)
21. Music mode (Classic)
22. Soft White

Audio and Media
SHORTCUT FN+Q FN+W FN+E FN+R FN+T FN+Y FN+U
FUNCTION Play/Pause Stop Last track Next track Mute Increase Volume Decrease Volume

Full-size Keyboard Keys

                          SHORTCUT| FUNCTION
---|---
FN+=|  F12
FN+P| Print screen
FN + PGDN| Home
FN + INS|   End
FN+Del|    Swap all function keys (1,2,3…=)to F1-F12 (DEL key will light up white when on)

Easy automatic cordless connection
a. Connect the USB nano receiver to your computer into your PC USB port, wait until automatic installation has completed.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>