CATCHX Pro Precision Meets Power User Guide
- June 9, 2024
- CatchX
Table of Contents
CATCHX PRO BAIT BOAT
QUICK START GUIDE
Edited on 2022/10/12
Please visit https://rippton.com/tutorial to watch the video tutorial of CatchX PRO.
PLEASE READ SECTION 6 AND 7 IN THE USER MANUAL
BEFORE READING THIS GUIDE.
INTRODUCTION
Dear Customer, Thank you for purchasing the CatchX Pro bait boat.
CatchX Pro is an advanced smart fishing bait boat, which has a payload of 3kg
and a range of 500 meters. With the ergonomic handle, it is easy to carry
around with.
You can control the CatchX Pro either by our app named “Rippton” or the
remoter control. Hope you will enjoy every fishing journey with company of
CatchX Pro.
Before we start learning how to use it, please download the Rippton App on
your mobile device. You can find the Rippton App on the Google Play Store,
Samsung Galaxy Apps and App Store. Installing the app requires Android
System 8.0 or above and iOS 11.0 or above.
http://app.stavix.cn/index.html?app_name=mktech
Download the RIPPTON App
Search for “RIPPTON” on the Google Play Store, Samsung Galaxy Apps or App
Store or scan this QR code to install the app on your mobile device.
Installation of the Batteries
Use your hand or your own screwdriver to unlock the battery compartments.
Control of LED Light Belt
Double click the power button of the remote control to switch on/off both of the head LED light belt and the tail light belt.
Attach the Fishing Line
Press the button shown in square above to open hook release mechanism which
will be open for 5 seconds and close automatically. And attach the fishing
line when it is open.
Note: CatchX Basic Version has one antenna, and CatchX Pro Version has
two antennas.
How to Use the Remote Control
Warm Reminder: Please pay attention to the top bar of the remote screen before controlling your boat.
Brief
The CatchX Pro bait boat is capable of covering 500 meters controlled by its remote control. The remote control is equipped with a display screen and buttons of different functions as the image below shows. Please refer to Section 6 &7 of the User Manual for detailed function description.
Preparation of the Remote Controller
Step 3 Attach your mobile device to the mobile device holder clamp
Operation of the Joystick
TIP: Move the joystick to the right to the maximum extent for 3 seconds to unlock.
Releasing Berley and Hooked Fishing Line by the remote
If you intend to release hopper 1, press the button HOPPER1, long press the CONFIRM button, or long press the button Shortcut A to open hopper 1 without pressing the CONFIRM Button. Shortcut B is for hopper 2.
If you intend to release the hook, press the HOOK RELEASE button, wait till the screen shows “hook selected” and then long press the CONFIRM button.
For more details of using the remote control, please refer to Section 6&7 of the User Manual.
How to Use Your Mobile Device to Control
Notice: Preloading the map on the APP
When using the CatchX Pro in any new area, before connecting the CatchX Pro to
your mobile device, it is always necessary to enter the Rippton app first with
internet connection, enter the operation interface (refer to 5.2.1 and 5.2.2
below) to finish preloading the map where you intend to fish at.
Connection
Step 1: Open Wi-Fi setting on your phone and find “IN_xxxxxx” Step 2: Tap
the “IN_xxxxxx”” and enter the password 12345678.
Note: For the connection with the Hydrobat smart fish finder, please read
the manual for the fish finder separately.
Operation
Step 1: Open the Rippton app and tap “Device” on the top.
Step 2: Find the CatchX Pro and tap “Enter”.
Before setting a mission, please check the image below to understand what each icon stands for.
The Learner Mode (sailing range limited within 300m) is automatically on the first time you enter the page. It can be turned off in Parameter of Common Set.
Step 3: Calibration
A. After the boat connected with the APP, please tap the cog icon on top right
of the APP interface to enter “ COMMON SETTINGS “.
B. Tap the ellipsis icon on bottom right, then choose “CALIBRATE” after the boat has been put on the water surface and well connected to the remote. The boat will automatically finish the calibration on the water by itself.
Note:
It’s always necessary to calibrate the CatchX Pro at new locations where are
3km away from the last you have used the boat at.
Step 4: Set a Route for Casting Mission
-
Tap the “Mission Management” button (in square 1) on the top of left side to start setting a route for your casting mission. Press the green button to confirm (in square 2).
-
Tap the “H” button (in square 3) to set the home point for the mission. Move the map to set the “H” icon at your desired spot as the home point.
Re-tap the “H” button to confirm. -
After the home point has been set, long press the point you want in the green circle until the prompt box pops up.
-
Tap “Confirm”.
Repeat the above-mentioned process if you want to add more waypoints (but no more than 2 waypoints). -
If you want to delete the selected waypoint, tap it and then select “Delete” in the prompt box.
Step 5: Select the Hoppers
There are two ways to select hoppers, which directly decides the mode of the
mission: fully automatic and half automatic.
| Fully Automatic | Half Automatic. |
|---|
√ Before performing the mission, tap the selected waypoint, and then tap
“Hopper Selection” to confirm which hopper or fishing line to be released on
which waypoint.| √ If you start a task without selecting hoppers before the
CatchX Pro begins to sail, you need to confirm which hopper to be released
every time CatchX Pro reaches a selected waypoint.
|
Step 6: Perform the Mission
a) Tap “Start” in the right bottom corner.
b) Slide to start.
NOTE: The CatchX Pro will return to the home point automatically after the mission is completed.
If you intend to cancel the ongoing mission, there are two methods:
- tap the “Return to Home Point” button. The boat will go back to the home point set previously; or
- move the joystick on the remote control downwards for 3 seconds, the operation mode will turn to “Manual” and the boat will stay at the position it stopped.
Step 7: Release the Hook
a) When the CatchX Pro arrives the point where you want to release the hook, tap the third button on the left side. You can also select the point to release the hook when selecting the hoppers before the mission starts.
b) Slide to cast.
Step 8: Reset the Hoppers and Hook
When a mission has been completed, the indicator color of the used hopper(s)
and hook will turn gray from green as shown at the bottom of the left picture.
Please tap “Reset” button to have the status of all the hoppers and hook
become available again.
Charging
CatchX Pro Bait Boat
Direct charging 5.5/2.5 DC charging port (please refer to Picture1). Please
note that both batteries must be inside the boat together when direct
charging. It takes 4-6 hours to be fully charged; or
Charging the batteries separately (please refer to Picture2) after taking
those out of the battery compartment.
Remote Control
Connect type-C side of the controller charger to the power port. It takes 2-3 hours to be fully charged.