Lucci decor 011463 Finn Pendant Instruction Manual

Installation Instructions

FINN PENDANT
SKU# 011462, 011463, 011465
Rated Voltage 220-240V~ 50Hz
Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation, and use of this product. Please keep instructions for future reference.

Warranty

• This light fitting is covered by a 12-month warranty. The warranty is from the date of purchase, not the date of installation.
• If the fitting is not installed by a licensed electrician the warranty will be void.
• Please retain the proof of purchase and evidence of installation by a licensed electrician.
• The warranty will be void if there is any damage due to improper usage or modification to the fitting.
• Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.

Installation Requirements

• Must be installed by a licensed electrician.
• All wiring and installation of the light fitting must adhere to local and national wiring rules. eg. AS/NZS 3000:2007/Amendment 2:2012 Electrical installations.
• Do not exceed the maximum wattage rating.
• Select a suitable location for installation:
  • This product is suitable for indoor use only.
  • The mounting point must support 2 times the weight of the fitting.
  • Ensure the fitting is not installed in the direct line of an air vent/system.
  • When installing a fitting in an area prone to moisture, ensure that the area is well ventilated and an appropriately rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product fault, and as such is not covered under warranty.
• Take care not to pull any electrical wires during unpacking as this may damage the connection.
• Lay out all the components on a smooth surface and make sure there are no components missing before assembling. If parts are missing, return the complete product to the place of purchase for inspection or replacement.
• Check whether the fitting has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair, or replacement.
• Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.

Installation Directions

1. Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material.

2. Remove the mounting bracket (B) from the canopy (E) by loosening the screws (C) on the side.

3. Use the mounting bracket (B) as a template to mark the screw positions on the ceiling.

4. Install the mounting bracket (B) onto the ceiling by using appropriately sized mounting screws (D) and anchors (A).
   Ensure the screws (D) and anchors (A) used are suitable for the mounting surface and surrounding environment.

5. Connect the main supply wire to the terminal block (F) in the canopy (E).
   Mains Supply Wire| Fitting Wire
   ---|---
   Earth – Yellow/Green | Yellow/Green or
   Neutral – Blue or Black| Blue
   Live – Brown or Red| Brown

6. Ensure the wires are secure and no bare wires are exposed.

7. Install the canopy (E) onto the mounting bracket (B) by tightening the screws (C) on the side.

8. To adjust the angle of the shade, loosen the cord anchorage (G) followed by the knob (H).
   When adjusting the shade, do not adjust more than 90° as this may damage the internal wires.
   Adjust the angle of the shade and re-tighten the knob (H) and the cord anchorage (G).

9. Install a globe (I – not included) into the lamp holder. Do not exceed the maximum wattage rating.

10. After the installation, switch on the fitting to test and enjoy your new lighting product.

NOTE: Concrete is a natural material. Some variations in its appearance may occur which is normal and part of its design quality.

NOTE: When adjusting the shade, do not adjust more than 90° as this may damage the wiring.

Safety Tips

• Always ensure the power is OFF and the fitting has cooled down before performing any maintenance, cleaning, changing the globe, or making any adjustment to the fitting.
• To avoid injury or damage to the fitting, ensure that power leads and screws are secure before connecting the power.
• Select a suitable location away from liquids and hazards.
• Ensure that the fitting does not come in contact with corrosive chemicals, etc.
• To clean, wipe with a damp clean cloth. Never soak the fitting with water.

Specifications

v1.1

Documents / Resources

| Lucci decor 011463 Finn Pendant [pdf] Instruction Manual
011462, 011463, 011465, 011463 Finn Pendant, 011463, Finn Pendant
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>