Lucci decor 010277 Elliot Small Squat 205mm Pendant in Black Instruction Manual
- June 3, 2024
- Lucci decor
Table of Contents
Lucci decor 010277 Elliot Small Squat 205mm Pendant in Black Instruction
Installation Instructions
Elliot
SKU# 010277 / 010300
Rated Voltage 220-240V~ 50Hz
Thank you for purchasing this quality Lucci product. To ensure correct
function and safety, please read and follow all instructions carefully before
assembly, installation and use of this product. Please keep instructions for
future reference.
Warranty
- This fitting is covered by a 12 month warranty. The warranty is from the date of purchase, not the date of installation.
- If the fitting is not installed by a licensed electrician it will void the warranty.
- Please retain proof of purchase and evidence of installation by a licensed electrician for any warranty enquiries.
- Warranty will be void if there is any damage due to improper usage or modification to the fitting.
- Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void warranty.
Installation requirements
- Must be installed by a licensed electrician.
- All wiring and installation of the light fitting must adhere to local and national wiring rules. eg. AS/NZS 3000:2007/Amendment 2:2012 Electrical installations.
- Do not exceed the maximum wattage rating.
- Select a suitable location for installation;
- This product is suitable for indoor use only.
- The mounting point must support 2 times the weight of the fitting.
- Ensure the fitting is not installed in direct line of an air vent/system and is not placed in any moist or damp areas.
- Take care not to pull any electrical wires during unpacking as this may damage the connection.
- Lay out all the components on a smooth surface and make sure there are no components missing before assembling. If parts are missing, return the complete product to the place of purchase for inspection or replacement.
- Check whether the fitting has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.
- Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.
Installation directions
-
Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material.
-
Decide on the suspension length for your fitting. Loosen the cord anchorage (L) and adjust the suspension length and then re-tighten the cord anchorage (L). Take care not to damage the cord during adjustment.
-
Attach the screws (A) washers (B, D) and nuts (E) onto the mounting bracket (C).
-
Use the mounting bracket (C) as a template to mark the screw positions on the ceiling.
-
Install the mounting bracket (C) onto the ceiling by using appropriately sized mounting screws (J), washers (I) and anchors (H). Ensure the screws (J) and anchors (H) used are suitable for the mounting surface.
-
Remove the cover from the terminal block (K) and connect the mains supply wire.
Mains Supply Wire: Fitting Wire
Earth – Yellow/: Yellow/Green
Green Neutral –Blue or Black: Blue
Live – Brown or Red: Brown -
Ensure the wires are secure and no bare wires are exposed. Install the cover back over the terminal block (K).
-
Install the canopy (F) onto the mounting bracket (C) and secure with the decorative nuts (G).
-
Install a globe (not included) into the lamp holder. Do not exceed the maximum wattage rating.
-
After the installation, switch on the fitting to test and enjoy your new lighting product.
Safety tips
- Always ensure the power is OFF and the fitting has cooled down before performing any maintenance, cleaning, changing the globe or making any adjustment to the fitting.
- To avoid injury or damage to the fitting, ensure that power leads and screws are secure before connecting the power.
- Select a suitable location away from liquids and hazards.
- Ensure that the fitting does not come in contact with corrosive chemicals, etc.
- To clean, wipe with a damp clean cloth. Never soak the fitting with water.
Specifications
Specifications| |
---|---|---
SKU #| 010277| 010300
Model #| Black| Copper
Rated Voltage| 220-240V~ 50Hz|
Rated Wattage| MAX. 45W|
Lamp Holder| ES / E27|
Weight| 1.0kg|
Dimensions| H:205mm| Dia:200mm| Susp:1200mm|
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>