OWC Ministack STX High-Performance Workflow Solutions User Guide

: June 2, 2024
: OWC

OWC Ministack STX High-Performance Workflow Solutions

OWC-Ministack-STX-High-Performance-Workflow-Solutions-PRODUCT-
IMAGE

INTRODUCTION

SYSTEM REQUIREMENTS

Works with any Apple silicon Mac or iPad with Thunderbolt (USB-C), Apple ‘Intel’ Mac with Thunderbolt 3, or any Thunderbolt 4 PC. Works as a USB-C hub with SATA storage on any USB-A (with USB-C to USB-A adapter or cable sold separately) or USB-C equipped Mac, iPad, Chromebook, Android device, or PC.

macOS 11.1 or later for Thunderbolt hosts
macOS 10.14.6 or later for USB hosts
Windows 10 or later
Linux
iPadOS 14.1 or later
Chrome OS
Android 11 or later

SUPPORTED DRIVES

(1) 2.5-inch or 3.5-inch SATA 6Gb/s SSD or HDD
(1) NVMe M.2 SSD 2280

PACKAGE CONTENTS

OWC-Ministack-STX-High-Performance-Workflow-
Solutions-01

ABOUT THIS MANUAL

The images and descriptions may vary slightly between this manual and the unit shipped. Functions and features may change depending on the firmware version. The latest product details and warranty information can be found on the product web page. OWC’s Limited Warranty is not transferable and subject to limitations.

FRONT VIEW

OWC logo LED – Glows white when there is power but no data connection or when the device enters Sleep mode. The logo will glow blue when there is power and an active data connection.
SATA drive activity – Glows green when there is a power and data connection. Flashes green when there is data access (read/write).
NVMe M.2 SSD activity – Glows green when there is a power and data connection. Flashes green when there is data access (read/write).

REAR VIEW

Cling On mounting points – if you are using one or more OWC Cling On anchors to secure the Thunderbolt device cable(s), affix them here.
Thunderbolt 4 ports – connect compatible Thunderbolt 4 or Thunderbolt 3 devices.
Thunderbolt 4 host port – Use this port to connect the ministack STX to a host.
DC power in – connect the included power supply here.
Kensington Security slot – connect
Kensington security tether here.

OWC DRIVE GUIDE

These directions apply if you purchased the miniStack STX with drive pre- installed. Follow the steps below to use the OWC Drive Guide utility to format your miniStack STX for macOS or Windows. If you installed your own drives, please use the formatting method you are most familiar with or review our Mac & PC Formatting page: owcdigital.com/support/formatting

Power on the ministack STX and plug it into to your computer using one of the included data cables. If you prefer to use a different formatting utility, do so at this time and skip the rest of these steps.
The disk will mount and your operating system will display it as “OWC SETUP”.
Open the disk icon to view its contents.
Double-click the OWC Drive Guide application. Follow the simple on-screen instructions to complete the formatting process. Once the formatting is finished the drive is ready to use.

USAGE NOTES

For the safe removal of your drive and to ensure that no data is lost, always eject or unmount the corresponding disk(s) from your operating system before powering off. You can use the methods described below to safely unmount your disk(s).

macOS:
- Drag the icon for the disk you wish to unmount to the trash can; OR
- Right-click the disk icon on the desktop, then click “Eject”; OR
- Highlight the disk on your Desktop and press Command-E.
Windows:
- Go to the System Tray (located in the lower right corner of your screen). Click on the “Eject” icon
  (a small green arrow over a hardware image).
- A message will appear, detailing the devices that the “Eject” icon controls, i.e., “Safely remove…” Click on this prompt.
- You will then see a message that says, “Safe to Remove Hardware.” It is now safe to disconnect the miniStack STX from the computer.
- The steps above are applicable to Windows 10 build 1803 and earlier. If you are using Windows 10 build 1809 (October 2018) or later, you can eject the drive by clicking the ‘Show hidden items’ menu in the Taskbar, then clicking ‘Safely Remove Hardware and Eject Media’, and last select the ‘Eject’ option for this volume.

INSTALLATION

ASSEMBLY

This section describes the process of installing drives into the ministack STX. If you purchased the ministack STX with drives pre-installed, please proceed to section 1.7 OWC Drive Guide. The Installation video can be watched by visiting go.owc.com/ministackstx/install.

Required Tools : Philips PH02 Driver

Place the ministack STX upside-down and remove the four screws on the bottom side of the outer case.
While gripping the ministack place it right-side up with the OWC logo facing forward. Slowly life the top case off from back to front.
NOTE: There is a cable clipped inside to the outer case and connected near the NVMe M.2 SSD circuit board. Opening slowly helps prevent unintendedly disconnecting the cable.
Carefully remove the cable from the routing clip. Then carefully disconnect the cable by pulling on the cable connector near the NVMe M.2 SSD circuit board. Please do not directly pull on the cable.
Drive Installation
(Note: Either a 3.5-inch or 2.5-inch drive and a NV Me M.2 SSD can be installed.)
Place the 3.5-Inch drive into the chassis and connect into the SATA connector on the circuit board. Make sure the drive is fully seated. Secure the drive from the inside using the included HDD Mounting Screws. Turn over the ministack and further secure the drive using the HDD Mounting Screws.
Place the 2.5-Inch drive into the chassis and connect into the SATA connector on the circuit board. Make sure the drive is fully seated. Turn over the ministack and further secure the drive using the SSD Mounting Screws.
Remove the NVMe M.2 SSD mounting screw and insert a NVMe M.2 SSD fully into the connector at a slight angle. Press the NVMe M.2 SSD down so the drive’s notch fits around the mounting post. Secure the drive by using the NVMe M.2 SSD mounting screw that was first removed.
Carefully place the cable back into the cable routing clip.
Then carefully connect the cable back into the connection near the NVMe M.2 SSD circuit board.
Place the top case back on the ministack from front to back and while gripping, flip the unit upside down. Secure the ministack by using the four removed case screws.
Move onto Mac & PC Formatting found in Section 3.2 to complete the setup of the ministack STX drive(s).

SUPPORT RESOURCES

TROUBLESHOOTING

Begin troubleshooting by verifying that the power cable is connected to the ministack STX and to a power source. If the power cable is connected to a power strip, make sure that the power switch on the strip is turned on. Then, verify that the Thunderbolt 4 cable is properly plugged into the computer and the host port on the ministack STX.
If the ministack STX is still not working properly, try connecting to another computer or using another Thunderbolt 4 cable. If you are still experiencing problems, consult Section 3.4 for OWC technical support contact information.

ONLINE RESOURCES

Data Migration: owcdigital.com/migrating-your-mac-os-x-installation-to-a-new-drive
Mac & PC Formatting: owcdigital.com/support/formatting
Installation Video: – Begin troubleshooting by verifying that the power cable is connected to the ministack STX and to a power source. If the power cable is connected to a power strip, make sure that the power switch on the strip is turned on. Then, verify that the Thunderbolt 4 cable is properly plugged into the computer and the host port on the ministack STX.
If the ministack STX is still not working properly, try connecting to another computer or using another Thunderbolt 4 cable. If you are still experiencing problems, consult Section 3.4 for OWC technical support contact information.

ONLINE RESOURCES

Data Migration: owcdigital.com/migrating-your-mac-os-x-installation-to-a-new-drive
Mac & PC Formatting: owcdigital.com/support/formatting
Installation Video: go.owc.com/ministackstx/install
Product Overview Page: https://eshop.macsales.com/shop/owc-ministack-stx
Product Overview Page: https://eshop.macsales.com/shop/owc-ministack-stx

ABOUT DATA BACKUP

To ensure that your files are protected and to prevent data loss, we strongly suggest that you keep two copies of your data: one copy on your OWC ministack STX and a second copy on your internal drive or another storage medium, such as an optical backup, or on a second external storage unit. Any data loss or corruption while using the ministack STX is the sole responsibility of the user, and under no circumstances may OWC, its parent, partners, affiliates, officers, employees, or agents be held liable for loss of the use of data including compensation of any kind or recovery of the data.

CONTACTING TECHNICAL SUPPORT

Phone: M–F, 8am–6pm CT
- 1.866.692.7100 (N. America)
- +1.815.338.4751 (Int’l)
Chat: M–F, 8am–6pm, Sat 9am–5pm CT
- www.owc.com/support
Email: Answered within 48 hours
- www.owc.com/support

CHANGES:
The material in this document is for information purposes only and subject to change without notice.
While reasonable efforts have been made in the preparation of this document to assure its accuracy, OWC, its parent, partners, affiliates, officers, employees, and agents assume no liability resulting from errors or omissions in this document, or from the use of the information contained herein. OWC reserves the right to make changes or revisions in the product design or the product manual without reservation and without obligation to notify any person of such revisions and changes.

FCC STATEMENT

Warning! Modifications not authorized by the manufacturer may void the user’s authority to operate this device.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

WARRANTY

The miniStack STX has a 3 Year OWC Limited Warranty if it was bundled with a drive.
OWC miniStack STX enclosures that do not ship with a drive have a 1 Year OWC Limited Warranty.
For up-to-date product and warranty information, please visit the product web page.

COPYRIGHTS AND TRADEMARKS

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written consent of OWC.
© 2022 Other World Computing, Inc. All rights reserved. ministack, OWC, and the OWC logo are trademarks of New Concepts Development Corporation, registered in the U.S. and/or other countries.
Mac and macOS are trademarks of Apple Inc. Thunderbolt and the Thunderbolt logo are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries. All other marks may be the trademark or registered trademark property of their owners.