pTron Pulsefit F21 Plus Bluetooth Fitness Smartwatch User Guide

pTron Pulsefit F21 Plus Bluetooth Fitness Smartwatch

Important: This Smartwatch is Not a Medical Device.

Requirements:
Android 5.0 & above | iOS 9.0 & above Bluetooth 5.0

Caution:

1. Clean the Smartwatch regularly, especially its inner side, and keep it dry always.
2. Adjust the Smartwatch tightness to ensure air circulation.
3. Excessive skincare products should not be used on the wrist wearing the smartwatch.
4. Please cease wearing the smartwatch in case of skin allergy or any discomfort.

Power On the Watch:
Long press the crown-like button on the side of the smartwatch for 3 seconds or plug in the Magnetic charging cable to charge the watch.

Downloading ‘Da Fit’ Mobile App:

1. For downloading the App go to Playstore or App Store and search ‘Da Fit’. Now, download and install the app.
   OR
   Type in Your Phone Browser
   http://plus.crrepa.com/app-download/dafit
   Now, download and install the app.
   OR
   Switch on the smartwatch, go to settings and then inside setting you will find QR code option, just click on it you will get the QR code. Now, scan the QR code from your phone, you will get a link for downloading ‘Da Fit’ app. Download and install the App in your smartphone.

Charging the Smartwatch:

1. Turn OFF the Smartwatch before Charging.
2. Simply, hold the 2-pin connector of the USB charging cable near the 2 small round magnetic charging interfaces. The connector will get connected to the interface through the magnetic pull. It’s a completely sealed system free of exposed contacts. Plug the USB end of the cable into a DC5V/1A power source.
3. When the smartwatch is fully charged, remove the watch from charging and unplug the USB charging cable from the power source. Note: You can directly check the charging by pressing the crown-like button on the right side of the dial. Pressing once will show the charging status on the display.

Binding Pulsefit F21+ with Mobile App:

1. After mobile App installation, open the App and set up your profile.
2. Now, go to the smartwatch option and there you will find “Add a device” (at the bottom menu, you will see a smartwatch icon, click on it).
3. Click on “Add a device” & then select your smartwatch.
4. In this way, your smartwatch will get bind with your smartphone.

Full Touch Control Display:

Phone Calls:
After connecting the smartwatch with the phone if there is an incoming call then a notification will emerge on the smartwatch and will display the option to reject the call or to hide the notification and along with that, the smartwatch will vibrate too.

Music Player:

1. After connecting the smartwatch with a smartphone, you can remote control the music player on your phone through the smartwatch.
2. First, start music from the phone, and then you can control the phone’s music player – Play/Pause/Next Song/Prev. Song.

Steps:
Smartwatch automatically tracks the steps and can be seen in the watch. Need to wear the smartwatch properly to get the real data.
Note: At midnight the data or the movement stats will get zero automatically.

Sleep:
Wear the smartwatch properly before sleeping, then it will provide the data of hours slept and the quality of sleep stats in the mobile App and in the smartwatch.
Note: Sleep stats will get zero at 8 PM automatically.

HR (Heart Rate):

1. The Smartwatch can record your heart rate all day.
2. You could also tap on the HR function page to start measuring heart rate. The optical sensor at the backside of the dial will start flashing green light.
   Note: This smartwatch is not a medical device.

BP:

1. Tap on the Blood Pressure function page to start measuring your blood pressure. The optical sensor at the backside of the dial will start flashing green light.
2. On the Blood Pressure page, you can view the blood pressure measurement data of the last times.
   Note: This smartwatch is not a medical device.

SpO2 (Blood Oxygen):

1. Tap on the SPO2 function page to start measuring your SPO2.
2. On the SPO2 page, you can view the SPO2 measured data of the last time.
   Note: This smartwatch is not a medical device.

Weather:
On the Weather function Page, you we can view the current temperature.

Exercise:

1. Tap on this icon in the menu, you will find exercise modes – Walking, Running, Cycling, Skipping, Badminton, Basketball & Football.
2. You can select any of the 1 exercises and the stats will be monitored on the watch.

Remote Capture:
Have remote capture feature to access the camera of the connected device, click to shutter. Note: This feature allows you to control your phone’s camera shutter through Bluetooth.

Reminders:

1. To Move: Can be activated and its valid time is from 10:00 – 22:00. This function will remind you to move/relax after 1 hour of sitting by vibrating.
2. To Drink Water: Can be activated and can set time intervals & duration as per our requirement.
3. Physiological Cycle Reminder: There are 3 reminder modes: Menstrual management, Pregnancy conditioning and gender health.
   Note: You can turn on/off these features via App.

Clock:

1. ALARM – Can set 3 alarms.
2. TIME FORMAT – Can change the time format in 12 hour or 24 hour format.
3. COUNTDOWN – Have countdown for 1, 3, 5, 10, 30 minutes and 1 & 2 hour.
4. STOPWATCH – This can be used as like a timer.

Other Features:

1. BRIGHTNESS – Can adjust (increase or decrease) the Brightness level.
2. THEATRE MODE – After activating theatre mode, smartwatch will turn off the vibration & turn down the brightness.
3. TORCH – While switching it ON, the watch display will get turned on, which provides some light in a dark place.
4. DISTURB – Turn ON to stop getting notifications.
5. LANGUAGE – Can change the language of the smartwatch through App with the connected device.
6. FIND DEVICE – Can click on this with the connected device in the App and the smartwatch will start vibrating.
7. QUICK VIEW – Just turn the wrist and the screen will appear.
8. DIAL SWITCH – From this you can select any of the wallpaper for the smartwatch screen.
9. WATCH FACES – From the app you can select the wallpaper or you can also select any of the pictures from the gallery of the connected device to set as a wallpaper in the smartwatch.

Frequently Asked Question

Q1) Why does the smart watch automatically disconnect Bluetooth when the Android screen goes out?
A)

1. Lock background APP. When the Da Fit process is cleared, the smartwatch will be disconnected from the mobile phone.
2. Set APP self-startup.
3. Unrestricted background operation. The Android mobile phone installed with APP intelligently restricts the background operation by default, and APP should be set manually without any restriction.

Q2) Why cannot the smartwatch receive message push?
A)

1. Please confirm that you have turned on the switch for message push at the mobile phone client.
2. Please confirm that messages can be displayed normally in the mobile phone notification bar. The message push on the smartwatch is completed by reading the message from the mobile phone notification bar. The smartwatch will not receive the message push if there is no message in the mobile phone notification bar.
3. In the app, you will find notifications option and there need to Turn on the switch to synchronize related information to smartwatch.
   If the message is pushed abnormally, it can be restart Notification access service to repair.

Q3) Why can’t take a hot bath with the smartwatch?
A) The bath water has a relatively high temperature and generates a lot of vapour which is in the gas phase with small molecular radius and can easily infiltrate into the smartwatch from the shell gap. When the temperature drops down, the vapour will condense into liquid-phase droplets which will easily cause the short-circuit inside the smartwatch and damage the circuit board and then damage the smart bracelet.

Important:

1. This smartwatch is NOT a Medical Device.
2. During swimming adhere to IP68 waterproof protocol.
3. Please connect the band when synchronizing data.
4. Use the 5V USB charging adapter only.
5. Do not expose the band in high moisture or extreme high temperatures or dry/liquid chemicals.
6. When the APP crashes or reboots, please check the phone memory, clear it and try again, or exit the app to reopen it.
7. Strap is not covered in manufacturer warranty.
8. Manufacturer/brand owner reserves the right to modify the content of this user manual without prior notification. Some functions are different in the various software versions, which is normal.

Disclaimer:
The colors and specifications shown/mentioned in the user manual may differ from the actual product. The images shown are for representation purposes only. Other product logos and company names mentioned herein may be trademarks or trade names of their respective owners.

References

• Da Fit - Apps on Google Play

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>