NAVIG 8 R NAV-RCDRONE50 MAKO WiFi Drone User Manual

: June 2, 2024
: NAVIG 8 R

NAVIG 8 R NAV-RCDRONE50 MAKO WiFi Drone

To help get you started, please refer to the quick connection guide below

NAV-RCDRONE50

NAV-RCDRONE50

3

CONTROLLER COMPONENTS

SETTING UP THE CONTROLLER / DRONE

INSTALLING THE CONTROLLER BATTERIES

Unscrew the battery cover, and insert 3 *AA batteries, making sure you insert them following the correct polarity as shown.
Re-attach the battery cover

NOTICE

Always have an adult to install the batteries
Always use Alkaline Batteries
Never mix old and new batteries

FOLDING THE ARMS

FOLD THE ARMS IN NUMERICAL SEQUENCE AS SHOWN BELOW

INSTALL THE PROTECTOR

Pull out the cover, as shown in Pic

Press down on the locking plate and simultaneously push into the slot, as shown in Pic
The protector is now installed.

CHARGING YOUR DRONE BATTERY

BATTERY WARNING:
Lithium Polymer batteries can expand, burst or catch fire if used incorrectly, causing both property damage and or personal injury. It is essential that you follow all the included instructions and safety warnings in full. The manufacturer, distributors and retailers will assume no liability for the failure to comply with these safety instructions and warnings.

INSTRUCTIONS WHEN CHARGING

The battery must be removed from the product before charging.
If the battery has just been used, please let it cool down to room temperature before charging.
Charging must only be undertaken by an Adult, and only using the charger included with this product.
Always charge the battery on a non flammable heat resistant surface with non flammable surroundings.
Connect the battery to the USB charging cable
Connect the USB charging cable to your USB Charger. The red LED on the USB charging cable will light up while charging and will turn off once the battery has fully charged.
Lithium Polymer batteries do not last forever. If your battery becomes damaged in a crash or no longer charges properly, immediately replace it with a new battery. To prolong the life of your battery, it is always best to retain a bit of charge in your battery prior to charging it.
Note: Only use the included USB charging cable.

SAFE FLIGHT ENVIRONMENT

Make sure the surrounding area is free of people, pets or other obstacles before you start to fly.
The Drone is designed for Outdoor flying, or Indoors if you have enough space.
Do not use in strong wind.
Leave 1.5 meters between you and the Drone at all times.

SETTING UP THE SIGNAL CONNECTION

Step 1
Inset the battery to the battery housing. (see first picture). Turn on the power switch of the Drone – the LED’s on the Drone will start to flash. Place the Drone down on a flat surface, making sure the drone is facing away from you.
Step 2
Press down the controller Power Switch to turn on the power, The controller will make fwo short BEEP SOund and the red LED will fiash. To pair the signals of the Drone and the Controller, you must RAISE the UP/DOWN Lever on the controller all the way to the TOP, It will make one short BEEP sound. And then LOWER it all the way to the BOTTOM, It will make one long BEEP sound. The next time you RAISE the UP/DOWN Lever the Drone will lift into the air.
Step 3
Always Turn off the Power Switch of the Drone after flight.
Step 4
Always turn the controller off after flight, and remove all batteries if leaving un-used for a long period of time.
Power switch

8.AUTO-HOVER

Tip: Below operation only available for altitude hold version.

START YOUR FIRST FLIGHT:
Push both control levers to the positions shown in the picture, and hold them for a few seconds then the motor will start working.

AUTO-HOVER:
Press the ” take-off /Land ” button (1) once, the drone automatically goes up to air and stays at a height of around 1.5 meters.
After that push the left stick to keep the drone at any height you want.
Press the ” take-off /Land ” button again, the drone will slowly go down to the floor and finally the motors stop spinning.

Emergency Button:
In case the drone is about to crash into an object, you can Press the ” Stop ” button (2) , at the same time, the motors will stop spinning at once and the drone falls to the floor immediately.
Make sure there are no people below the drone.

FLIGHT CONTROL

PLEASE USE THE CONTROLLER TO PRACTICE SIMULATED FLIGHTS BEFORE YOU ACTUALLY TAKE THE DRONE IN THE AIR FOR THE FIRST TIME

Place the Drone on a flat surface, making sure the Yellow LED Lights are facing away from you.

When you push Up on the Up/Down Lever the Drone will start to go Up (please do this slowly at first till you learn the sensitivity).
When you push Down on the Up/Down Lever the Drone will start to go Down
When you push Forward on the Forward/Backward Lever the Drone will start to fly Forward (please do this slowly at first till you learn the
sensitivity). When you push Backwards on the Forward/ Backward Lever the Drone will start to fly Backwards.
When you push Left on the Turn Left/Turn Right Lever the Drone will start to spin Left. When you push Right on the Turn Left/Turn Right Lever the Drone will start to spin Right.
When you push Left on the Bank Left/Bank Right Lever the Drone will start to Bank Left (please do this slowly at first till you learn the sensitivity) . When you push Right on the Bank Left/Bank Right Lever the Drone will start to Bank Right.

TIP: It is much easier when you start to learn to fly the Drone, to ignore Turn Right / Turn Left.
By using Up/Down, Forward/Backward, Bank Left/Bank Right, the Drone will still be able to fly anywhere.

HOW TO DO A 360 FLIP

Make sure the Drone is flying at least 3 meters above the floor, or 3 meters bellow a ceiling.
Press the Flip button on the controller, The controller will make a “Beep” sound, then flick the right hand lever in any direction, and the Drone will flip in that direction.
You may need to push Up on the Up/Down Lever after the flip, if your battery is low on power in order to keep the Drone high in the air after the Flip.

FEATURES

SPEED CONTROL: When you first turn on your Drone, it is set to 25% speed, you will hear ONE beep.
When you press the SPEED BUTTON, you will hear TWO beeps and the speed will be increased to 50%.
Pressing the SPEED BUTTON again you will hear THREE beeps and the speed will increase to 100%.
Pressing again will bring you back to 25% speed and you will hear ONE beep. Always learn to fly at 25% speed, and then you can increase it as you get better at flying.

FLIGHT ADJUSTMENT SECTION

When you lift your Drone into the air, and don’t use any of the other direction levers, your Drone should simply hover in one spot without moving in any other direction. If however it doesn’t, you can follow the bellow instructions to TRIM your Drone back to a perfect hover. TRIMMING is always needed before your first flight.

If your Drone banks to the Left, keep pressing the Bank Left/Bank Right Trim Button to the Right till the Drone stops banking.
If your Drone banks to the Right, keep pressing the Bank Left/Bank Right Trim Button to the Left till the Drone stops banking.
If your Drone flies Backwards, keep pressing the Forward/Backwards Trim Button Up till the Drone stops flying Backwards.
If your Drone flies Forwards, keep pressing the Forward/Backwards Trim Button Down till the Drone stops flying Forwards.

AUTO TRIM FUNCTION

Push both control levers to the positions shown in the picture, and hold them for a few seconds. The lights on the drone will start to flash. Now the drone is recovered to its original factory setting and ready to fly again.

HEADLESS AND ONE KEY RETURN FUNCTION

Headless function:
Press the Headless button as shown, you will get into compass mode flying.
To quit from this mode, press the same slider button again.
One key return function:
Press the One Key Return button as shown, you will get into one key return mode.
To quit from this mode, press the same slider button again.

EXTRA INSTRUCTIONS FOR CAMERA FUNCTIONS

Step1: Insert the memory card (not incl.) into the camera. You must make sure you insert the memory card the correct way up (see picture). If you insert the memory card up side down it will get stuck and your camera will not work.
Step 2: Turn on the the Power Switch of the Drone as you would for any normal flight.
Step 3: Four lights on the drone will flash once when taking photos and keep flashing when taking video.

Attention: When filming a video, always make sure to press the video button the second time to finish the video BEFORE you land and disconnect the Drone battery, as otherwise your video will not save.

Insert the Memory Card into the USB Memory Card Reader (not inlc.) making sure you insert it the correct way as shown

Turn the On/Off switch on the Drone to Off, and remove the Memory Card from the camera. Insert the Memory Card into the included USB Card Reader (making sure you insert it the correct way round – see picture), and attach the USB Card Reader (not incl.) to your computer. You will now be able to open the Photo/ Video files saved on the memory card on your computer in exactly the same way you open other pictures and videos saved on memory cards or sticks. The AVI format of the video will need a media player which supports AVI format.

EXTRA INSTRUCTIONS FOR APP FUNCTIONS

SOFTWARE DOWNLOAD AND INSTALLATION

SEARCH FOR “NAVIG[8]R FD” , “WI-FI 720P” , “XSW UFO”, or “WiFi UFO”

USAGE INSTRUCTIONS

Connect the model to the power, the indicator on camera lights up .
Enter the “setting” menu of your mobile device and turn on WIFI.
Find a network WIFI called “NAV-RCDRONE” click connection until “connected”.
Open the “NAVIG[8]R FD”, “XSW UFO”, “WiFi UFO” OR “WI-FI 720P” software, click the “play” icon into the control interface. And you will see the real time video.

REPLACING BLADES AND FIXING ISSUES

BLADE REPLACEMENT: Your Drone blades are very strong, but sometimes they can get damaged with a bad crash. You have spare blades in the box, and to replace them it is as easy as just placing a new one back on over the motor bar. You must always replace an A Blade with an A Blade, and a B Blade with a B Blade.
Drone NOT LIFTING OR NOT FLYING IN YOUR CHOSEN DIRECTION:
The most common reason for a Drone not lifting or flying in your chosen direction properly is that you have hair and debris wrapped around one or more of the blades. This is simple to remove, just take off the blade. Remove the debris, and place the blade back on.
The batteries in either the Drone or Controller may need charging (or replacing if it’s the batteries in the controller).
You may have knocked your Trim Button settings out of sync. Follow the instructions earlier in this booklet to reset them back to the factory settings, and then re-trim as desired.

WARNINGS:

The Drone is designed for 14+
Adult supervision is always advisable with any form of flying toy
Always ensure your flight area is free of all obstacles before taking off, and ensure the Drone is always flown in excess of 1.5 meters from yourself and others
Remove all batteries from the Drone and Controller when not in use
Never overcharge
Never leave to charge unattended
Never touch the Drones motors during or after flying as they can get hot
Never touch the blades when they are in motion
If the Drone becomes damaged, stop using it immediately
Do not dispose of any parts of the Drone or Controller in the normal rubbish; all parts should be taken to your local recycling centre
The battery in the Drone should never be exposed to any form of high temperature or disposed of in a fire

SPECIFICATIONS

Drone:

Battery: Li-Po 3.7V 1800mAh
Flight Time: 15 minutes
Charing Time: Up to 160 minutes
Camera Photo: 2.0 MP
Camera Video: 720P

Controller:

Transmission Range: 40m
Operating Frequency: 2.4GHz
Battery: 1.5V AA x3

WARRANTY AGAINST DEFECTS

Laser warrants your new product to be free tromp defects in materials and workmanship Tor 12 months, from the date of purchase, provided that the product is used in accordance with accompanying recommendations or instructions where provided. The benefit of this warranty is in addition to your rights under the Australian Consumer Law and to other rights and remedies of the consumer under a law in relation to the goods or services to which the warranty relates.

Through a network of retailers and resellers, Laser will provide you with your choice of a refund, repair, or exchange (where possible) for this product if it becomes defective within the warranty period. This warranty will no longer apply where the defect is a result of alteration, accident, misuse, abuse, normal wear and tear, neglect, or improper storage. Please retain your receipt as proof of purchase

How to make a product warranty claim:

Find your receipt with date of purchase. If this is not available, Laser will make an assessment based on the date of manufacture, condition of the product and type of defect.
Please contact your original place of purchase. They will assess the nature of the fault and refund or replace the product as per their store refund or warranty policy.
If your original place of purchase cannot be contacted, please contact Laser with a description of the taut. Io assist our team in providing you with a quick resolution, please include any photos and/or a short video demonstrating the fault with your product.
- Phone: (02) 9870 3355
- Email: support@laserco.com.au
- Online: www.laserco.net/support/warranty and follow the website instructions
- Business Address: U1 6-8 Byfield Street, Macquarie Park, 2113, NSW, Australia
Laser will review your claim and in the first instance, attempt to troubleshoot and resolve the issue for you without the need to return the product.
If it is determined via troubleshooting that your product may be faulty, our team will provide instructions to have the product returned for assessment. If the product does need to be returned within the warranty period, Laser will arrange return shipping at no cost to you.
Once we receive the product, our experienced technicians will assess it and determine how best to resolve the issue.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

For more helpful guides visit us at

LASER
www.youtube.com/LasercoAu www.laserco.com.au

IMPORTANT SAFETY INFORMATION
Congratulations on your purchase. We hope you have a lot of fun with it but there are just a few things you need to remember for everyone’s safety.

You must only operate this aircraft in your line-of-sight in daylight. Don’t let it get too far away from you.
You must not fly closer than 30 meters to vehicles , boats , buildings or people
You must not fly over any populous area , such as beaches, other people’s backyards, heavily populated parks, or sports ovals where there is a game in progress
If you are in controlled airspace, which covers most Australian cities, you must not fly higher than 400 feet (120 meters)
You should not fly within 5.5 km of an airfield .
It’s illegal to fly for money or economic reward unless you have an unmanned operator’s certificate issued by the Civil Aviation Safety Authority (CASA).

Further information
Model Aeronautical
Association of Australia
www.maaa.asn.auSafe and happy flying!

CASA