MotorGuide R3-55 Hand Control Transom Mount Instruction Manual

MotorGuide R3-55 Hand Control Transom Mount

EU Compliance Statement
Attwood Corporation hereby declares that the MotorGuide R3 trolling motor is in compliance with the essential requirements and other relevant provisions of the 99/5/EC R&TTE directive.

CE Declaration

• Manufacturer: Attwood Corporation
• Address: 1016 N. Monroe
• Lowell, MI 49415 USA
• Telephone: 616‑897‑9241
• Authorized Representative: Brunswick Marine
• Parc Industriel de Petit‑Rechain
• B‑4800
• Verviers, Belgium
• Telephone: +32(0)87323222
• Product: MotorGuide R3 Series
• Model: includes all 12, 24, and 36-volt DC models
• Council Directive 2004/108/EC ‑ Electromagnetic Compatibility
•  EN 55012:2008; A1:2010 ‑ Vehicles, boats and internal combustion engines. Council Directive 98/96/EC ‑ Maritime Equipment Directive
•  EN 60945:2002+C1:2008 ‑ Maritime navigation and radiocom. equip. (Motor systems)
•  CISPR16 ‑ Conducted and Radiated Emissions
•  EN61000‑4‑2:2008 ESD
•  EN61000‑4‑3:2006 Radiated Immunity
•  EN61000‑4‑4:2004 EFT
•  EN61000‑4‑5:2005 Surges
•  EN61000‑4‑6:2008 Conducted Susceptibility
•  EN61000‑4‑8:2001 Magnetic Field Immunity
•  EN6100‑4‑11:2004 Voltage Dips and Interrupts

Council Directive 2006/42/EC ‑ Machinery

• EN ISO 12100 ‑ Safety of machinery ‑ General principles for design, risk assessment and reduction
• An official copy of the Declaration of Conformity can be found at http://www.motorguide.com/support/certifications.

Thank You
Thank you for choosing MotorGuide, one of the finest trolling motors available. Years of experience have been committed to the goal of producing the finest quality products. This led to MotorGuide’s reputation for strict quality control, excellence, durability, long‑lasting performance and being the best at providing after‑the‑sale service and support. Please read this manual carefully before operating your motor. This manual has been prepared to assist you in the operation, safe use, and care of your trolling motor. Again, thank you for your confidence in MotorGuide.

Warranty Message
The product you have purchased comes with a Two Year Limited Warranty from MotorGuide, the terms of the policy are set forth in the Warranty Information section of this manual. The policy statement contains a description of the duration of coverage, important disclaimers and limitations of damages, and other related information. Please review this important information. The description and specifications contained herein were in effect at the time this manual was approved for printing. MotorGuide, whose policy is one of continued improvement, reserves the right to discontinue models at any time, to change specifications, designs, methods, or procedures without notice and without incurring obligation.MotorGuide, Lowell, Michigan U.S.A.

Copyright and Trademark Information
© MERCURY MARINE. All rights reserved. Reproduction in whole or in part without permission is prohibited. Alpha, Axius, Bravo One, Bravo Two, Bravo Three, Circle M with Waves Logo, K‑planes, Mariner, MerCathode, MerCruiser, Mercury, Mercury with Waves Logo, Mercury Marine, Mercury Precision Parts, Mercury Propellers, Mercury Racing, MotorGuide, OptiMax, Quicksilver, SeaCore, Skyhook, SmartCraft, Sport‑Jet, Verado, VesselView, Zero Effort, Zeus, #1 On the Water and We’re Driven to win are registered trademarks of Brunswick Corporation. Pro XS is a trademark of Brunswick Corporation. Mercury Product Protection is a registered service mark of Brunswick Corporation.

WARRANTY INFORMATION

MotorGuide Limited Two-Year Warranty
KEEP YOUR ORIGINAL PURCHASE RECEIPT

1. To obtain warranty service, the purchaser should deliver or return the unit (postage prepaid and insured) to any MotorGuide-authorized service center. DO NOT RETURN TO PLACE OF PURCHASE unless they are an authorized service center. Motors purchased in other countries should be returned to the place of purchase. Products returned by mail should be carefully packaged and include a note describing the nature of the problem and/or service requested the customer’s address and phone number. A copy of the receipt, Bill of Sale, registration verification, or other proof of purchase is required with the return of the product for warranty consideration. Warranty claims will not be accepted without the presentation of the purchase receipt for trolling motor, other verification of registration, or Bill of Sale for boat package.
2.  MotorGuide electric trolling motors are warranted to the original purchaser to be free from defects in material and/or workmanship for two (2) years. Warranty is NOT transferable to any subsequent purchaser.
3.  MotorGuide, at its discretion, will repair or replace items covered under the terms of this warranty. Neither MotorGuide nor MotorGuide service dealers are responsible for damages to MotorGuide products due to repairs performed by anyone other than the MotorGuide Factory Service Center. Neither MotorGuide nor Mercury Marine is responsible for failure or damage caused by improper installation, set‑up, preparation, or previous service or repair errors.
4.  Warranty coverage is available only to customers that purchase from a dealer authorized by MotorGuide/Mercury Marine to distribute the product in the country in which the sale occurred. Warranty coverage and duration vary by the country in which the product resides. This warranty applies to X3 series MotorGuide trolling motors sold and residing in the United States. This Limited Warranty begins on the date the product is first sold to a purchaser or the date on which the product is first put into service, whichever occurs first. MotorGuide accessories are covered by this Limited Warranty for a coverage period of one (1) year from the date of retail sale. The repair or replacement of parts, or the performance of service under this warranty, does not extend the life of this warranty beyond its original expiration date. Promotional warranties are not included in this statement and coverage may vary by promotion. The product either sold or put into service more than six years from date of manufacture is excluded from warranty coverage.
5.  MotorGuide Composite Shaft Limited Lifetime Warranty. MotorGuide composite shafts are warranted to the original retail purchaser to be free of defects in material or workmanship for the lifetime of the original purchaser. MotorGuide will provide a new composite shaft at no cost for any composite shaft which contains a defect in material or workmanship. The installation costs are the sole responsibility of the purchaser.
6. This warranty does not apply to normal worn parts, i.e., worn cables, adjustments, or product damage due to 1) neglect, lack of maintenance, accident, abnormal operation or improper installation or service; 2) abuse, i.e., bent metal columns, bent armature shafts, broken control cables, etc., accidents, modifications, misuse, excessive wear or damage caused by an owner’s failure to provide reasonable and necessary installation or care; 3) use of an accessory or part not manufactured by MotorGuide/Mercury; 4) alteration or removal of parts; 5) opening the lower unit (motor) by anyone other than the Factory Service Center will void this warranty.
7. This warranty will not apply to haul‑out, launch, towing and storage, transportation charges and/or travel time, telephone or rental charges of any type, inconvenience, or loss of time or income, or other consequential damages.
8.  We reserve the right to improve the design of any trolling motor without assuming any obligation to modify any trolling motor previously manufactured.
9.  Serialized “Service‑Repair” motors have a one (1) year warranty. Nonserialized “Service‑Repair” electric trolling motors are NOT warranted. “Service‑Repair” motor denotes a trolling motor sold by MotorGuide that may be “used,” but has been inspected and may have had minor repairs. The original retail purchaser of a “Service‑Repair” motor is the first purchaser of the motor after it is denoted as “Service‑Repair.” “Service‑Repair” motors have a blue sticker on the battery cable and box denoting “Manufacturer Certified Service‑Repair Motor.”
10. TERMINATION OF COVERAGE: Warranty coverage may be terminated for a repossessed product, or product purchased at auction, from a salvage yard, from a liquidator, from an insurance company, from unauthorized marine dealers or boatbuilders, or other third-party entities.
11.  ALL INCIDENTAL AND/OR CONSEQUENTIAL DAMAGES ARE EXCLUDED FROM THIS WARRANTY, WARRANTIES OF MERCHANTABILITY AND FITNESS ARE EXCLUDED FROM THIS WARRANTY, IMPLIED WARRANTIES ARE LIMITED TO THE LIFE OF THIS WARRANTY, SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS WHICH MAY VARY FROM STATE TO STATE.

GENERAL INFORMATION

Boater’s Responsibilities
The operator (driver) is responsible for the correct and safe operation of the boat and the safety of its occupants and the general public. It is strongly recommended that each operator (driver) read and understand this entire manual before operating the trolling motor. Be sure at least one additional person on board is instructed in the basic operation of the trolling motor in case the driver is unable to operate the boat. Protecting People in the Water

WHILE YOU ARE TROLLING
It is very difficult for a person in the water to take quick action to avoid a boat heading in their direction, even at slow speeds.

Always slow down and exercise extreme caution any time you are boating in an area where there might be people in the water.

WHILE THE BOAT IS STATIONARY
the spinning propeller, a moving boat, or any solid device attached to the boat can cause serious injury or death to swimmers. Stop the trolling motor immediately whenever anyone in the water is near your boat.Shut off the trolling motor before allowing people to swim or be in the water near your boat.

Passenger Safety Message
Whenever the boat is in motion, observe the location of all passengers. A sudden reduction in boat speed, such as a sharp change of boat direction, could throw them off the boat.

Safe Boating Suggestions
In order to safely enjoy the waterways, familiarize yourself with local and other governmental boating regulations and restrictions, and consider the following suggestions.

• Use flotation devices. It is the law to have an approved personal flotation device of suitable size for each person aboard and have it readily accessible.
• Do not overload your boat. Most boats are rated and certified for maximum load (weight) capacities, refer to your boat capacity plate. If in doubt, contact your dealer or the boat’s manufacturer.
• Perform safety checks and required maintenance. Follow a regular schedule and ensure all repairs are made properly.
• Never be under the influence of alcohol or drugs while boating (it is the law). Alcohol or drug use impairs your judgment and greatly reduces your ability to react quickly.
• Passenger boarding. Stop the trolling motor whenever passengers are boarding or unloading.
• Be alert. The operator of the boat is responsible by law to maintain a proper lookout by sight and hearing. The operator must have an unobstructed view, particularly to the front. No passengers, load, or fishing seats should block the operator’s view when operating the boat.
• Underwater hazards. Reduce speed and proceed with caution whenever navigating in shallow water.
• Tripping hazards. To avoid a trip hazard, route all cables and wiring neatly and out of the way.
• Report accidents. Boat operators are required by law to file a Boating Accident Report with their state boating law enforcement agency when their boat is involved in certain boating accidents. A boating accident must be reported if 1) there is loss of life or probable loss of life, 2) there is a personal injury requiring medical treatment beyond first aid, 3) there is damage to boats or other property where the damage value exceeds $500.00 or 4) there is a complete loss of the boat. Seek further assistance from local law enforcement.

PRODUCT OVERVIEW

R3‑30/R3‑40/R3‑45/R3‑55 MotorGuide Trolling Motor

•  Top housing
•  Extendable speed control tiller handle
•  Serial number
•  Positive and negative battery leads
•  Depth adjustment collar (R3‑45/55 model shown)
•  Tilt lock release lever (R3‑45/55 model shown)
•  Transom clamp screws
•  Column
•  Lower unit
•  Propeller
•  Clamp bracket (R3‑45/55 model shown)
• tearing tension collar
•  Clamp bracket assembly (R3‑30/40 model shown)
•  Tilt lock release button (R3‑30/40 model shown)
• Collar (R3‑30/40 model shown)

Specifications

Model

|

Control

| Freshwater/ Saltwater|

Volts

| Speeds Forward/ Reverse| Peak Thrust| Shaft Length
---|---|---|---|---|---|---

R3‑30

| Extendable hand/ twist‑tiller|

Freshwater

|

12 V

|

5/2

| 13.6 kgf (30 lbf)| 76.2 cm (30 in.)

R3‑40

| Extendable hand/ twist‑tiller|

Freshwater

|

12 V

|

5/2

| 18.1 kgf (40 lbf)| 91.4 cm (36 in.)
R3‑40 FW

Digital

| Extendable hand/ twist‑tiller|

Freshwater

|

12V

|

Variable

| 18.1 kgf (40 lbf)| 91.4 cm (36 in.)

R3‑45

| Extendable hand/ twist‑tiller|

Freshwater

|

12 V

|

5/2

| 20.4 kgf (45 lbf)| 91.4 cm (36 in.)
R3‑45 SW

Digital

| Extendable hand/ twist‑tiller|

Saltwater

|

12 V

|

Variable

| 20.4 kgf (45 lbf)| 45.7 cm (18 in.)
R3‑45 SW

Digital

| Extendable hand/ twist‑tiller|

Saltwater

|

12 V

|

Variable

| 20.4 kgf (45 lbf)| 91.4 cm (36 in.)
R3‑45 FW

Digital

| Extendable hand/ twist‑tiller|

Freshwater

|

12 V

|

Variable

| 20.4 kgf (45 lbf)| 91.4 cm (36 in.)

R3‑55

| Extendable hand/ twist‑tiller|

Freshwater

|

12 V

|

5/2

| 24.9 kgf (55 lbf)| 91.4 cm (36 in.)
R3‑55 FW

Digital

| Extendable hand/ twist‑tiller|

Freshwater

|

12 V

|

Variable

| 24.9 kgf (55 lbf)| 91.4 cm (36 in.)
R3‑55 FW

Digital

| Extendable hand/ twist‑tiller|

Freshwater

|

12 V

|

Variable

| 24.9 kgf (55 lbf)| 106.7 cm (42 in.)
R3‑55 SW

Digital

| Extendable hand/ twist‑tiller|

Saltwater

|

12 V

|

Variable

| 24.9 kgf (55 lbf)| 91.4 cm (36 in.)

WIRING AND BATTERY INFORMATION

• An operating or charging battery produces gas that can ignite and explode, spraying out sulfuric acid, which can cause severe burns. Ventilate the area around the battery and wear protective equipment when handling or servicing batteries.
• Performing service or maintenance without first disconnecting the battery can cause product damage, personal injury, or death due to fire, explosion, electrical shock, or unexpected motor starting. Always disconnect the battery cables from the battery before maintaining, servicing, installing, or removing motor components.

Standard Practices and Procedures
When installing or removing this trolling motor, follow these guidelines:

• Disconnect the trolling motor from the trolling motor battery.
• Use 12‑volt, deep-cycle marine batteries. The number of batteries required varies according to the model of your trolling motor. Refer to Battery Connection.
• As a general rule, deep cycle batteries with a higher amp‑hour rating or reserve capacity rating will provide longer run times and better performance.
• Install a manual reset circuit breaker in line with the trolling motor positive leads within 180 cm (72 in.) of the batteries. These can be purchased from your local MotorGuide retailer or from www.motorguide.com
• Do not extend the included 10‑gauge battery cables more than 1.8 m (6 ft) for a total of 3 m (10 ft). If longer battery cables are required, MotorGuide offers accessory 8 mm² (8‑gauge) battery cables.
• Use any lock nuts to secure the battery cables to their terminals. Using wing nuts to secure the battery cables can cause loose connections.
• Any depth sounders or fish finders must be powered from the engine starting battery. Connecting electronic equipment to the trolling motor batteries can cause electrical interference and possible electrolysis.
• An operating or charging battery produces gas that can ignite and explode, spraying out sulfuric acid, which can cause severe burns. Ventilate the area around the battery and wear protective equipment when handling or servicing batteries.

WIRING AND BATTERY INFORMATION

When charging batteries, an explosive gas mixture forms in each cell. Part of this gas escapes through holes in the vent plugs and may form an explosive atmosphere around the battery if ventilation is poor. This explosive gas may remain in or around the battery for several hours after it has been charged. Sparks or flames can ignite this gas and cause an internal explosion, which may shatter the battery. The following precautions should be observed to prevent an explosion:

1. Do not smoke near batteries being charged or which have been charged very recently.
2.  Do not break live circuits at the terminals of batteries, because a spark usually occurs at the point where a live circuit is broken. Always be careful when connecting or disconnecting cable clamps on chargers. Poor connections are a common cause of electrical arcs which cause explosions.
3.  Do not reverse the polarity of the battery terminal to cable connections.

Wire and Cable Routing

•  Route the trolling motor wires on the opposite side of the boat from another boat’s wiring.
•  Sensitive electronics, such as depth finders, should be connected directly to the main engine battery. Single battery systems require separate connection cables.

Battery Connection
Disconnecting or connecting the battery cables in the incorrect order can cause injury from electrical shock or can damage the electrical system. Always disconnect the negative (‑) battery cable first and connect it last.

1.  Install a 50‑amp (good) or 60‑amp (best) manual reset circuit breaker in line with the trolling motor power cable positive (+) lead and the battery positive (+) terminal. Connect the trolling motor positive lead to the trolling motor battery positive (+) terminal.
2.  Connect the black trolling motor power cable negative (–) lead to the trolling motor battery negative (–) terminal.
3. Connect a common ground bond from the trolling motor battery negative (–) terminal to the engine starting battery negative (–) terminal.

MM309922T
50‑amp manual reset circuit breaker| MM5870
60‑amp manual reset circuit breaker| 8M0064076

TROLLING MOTOR INSTALLATION AND OPERATION

Transom Mount Installation
NOTE: The R3‑30 and R3‑40 fit transoms up to 7.62 cm (3 in.). The R3‑45 and R3‑55 fit transoms up to 8.9 cm (3.5 in.).

1.  Place the trolling motor on the transom of the boat.
   IMPORTANT: Overtightening the transom clamp screws can weaken or damage the mount bracket.

2.  Tighten the transom clamp screws securely by hand.

   •  Transom clamp screw
   •  Mount bracket (R3‑45/55 model shown)
   •  Mount bracket (R3‑30/40 model shown)

Stowing and Deploying the Trolling Motor

• Rotating propellers can cause serious injury or death. Never start or operate the motor out of water.
• Moving parts, such as hinges and pivot points, can cause serious injury. Keep away from moving parts when stowing, deploying, or tilting the motor.
•  R3‑30 and R3‑40 models ‑ push down on the tilt lock release pin while simultaneously pulling on the trolling motor head/column. Do not exert a downward force on the tiller handle to assist in tilting the trolling motor.
•  R3‑45 and R3‑55 models ‑ push aft on the tilt lock release lever while simultaneously pulling on the trolling motor head/column. Do not exert a downward force on the tiller handle to assist in tilting the trolling motor.
•  Tilt lock release lever (R3‑45 and R3‑55 models shown)
•  Tilt lock release pin (R3‑30 and R3‑40 model shown)

When the desired tilt position is achieved, release the tilt lock release pin/lever. Verify that the latch pin is securely engaged.

• Tilt lock release lever (R3‑45 and R3‑55 model shown)
•  Latch pin
•  Tilt lock release pin (R3‑30 and R3‑40 model shown)

TROLLING MOTOR INSTALLATION AND OPERATION

1. Firmly grasp the trolling motor head/column and press on the tilt lock release pin/lever.
   • Tilt lock release lever (R3‑45 and R3‑55 model shown)
   •  Latch pin
   •  Tilt lock release pin (R3‑30 and R3‑40 models shown)
2.  Adjust the angle of the motor to the desired position.
3.  Release the tilt lock release pin/lever. Verify that the latch pin is securely engaged.

Adjusting the Steering Tension

1. Turn the steering tension knob clockwise to increase steering effort.
2. Turn the steering tension knob counterclockwise to decrease steering effort.
   •  Steering tension knob (R3‑45 and R3‑55 model shown)
   •  Friction strip
   •  Steering tension knob (R3‑30 and R3‑40 model shown)

Adjusting the Motor Depth
Adjusting the depth of the motor improves trolling motor performance in various water depths.
NOTE: It may be necessary to loosen the steering tension knob before adjusting the motor depth. High steering tension will prevent the motor column from moving up and down freely. Firmly grasp the column with one hand while turning the depth collar adjustment knob counterclockwise until the motor column slides freely. To secure the column in the desired depth position, turn the depth collar adjustment knob clockwise and tighten it securely. Readjust steering tension if necessary.

•  Depth collar adjustment knob
•  Depth collar
•  Steering tension knob (R3‑45 and R3‑55 model shown)

IMPORTANT: When adjusting the motor depth, ensure that the lower unit is submerged at least 25 cm (9.8 in.) to avoid propeller cavitation in choppy water.
Speed Control—Hand‑Operated ModelsAdjust the speed control to the desired direction and thrust level. Rotate the twist‑tiller handle clockwise for forward movement or counterclockwise for reverse movement. The “off” handle position stops the motor. Five‑speed models have five forward speed settings and two reverse speed settings.

Digital variable speed models allow you to select any speed from 0–10 in forward or reverse.

•  Forward speed control
•  Off
•  Reverse speed control

Battery Indicator Light (Digital Models Only)
The battery indicator light (located on the head cover) provides battery state‑of‑charge information at a glance. The battery light will turn on when the trolling motor is connected to the battery and will remain on the entire time that the motor is connected to the battery. Depending on the battery state of charge, the light will either be green (charged) or red (discharged).

MAINTENANCE

Trolling Motor Care
To keep your trolling motor in the best operating condition and retain its dependability, it is important that your trolling motor receives periodic inspections and maintenance. We urge you to keep it maintained properly to ensure the safety of you and your passengers. Neglecting to inspect, maintain, or repair your trolling motor can result in product damage or serious injury or death. Do not perform maintenance or service on your trolling motor if you are not familiar with the correct service and safety procedures.

SELECTING REPLACEMENT PARTS
We recommend using original MotorGuide Certified Tough replacement parts. Inspection and Maintenance Schedule

BEFORE EACH USE

•  Check the trolling motor for tightness on the transom.
•  Check the tightness of the battery lead connections.
•  Visually inspect for loose or corroded wiring connections.
•  Check the tightness of the propeller nut.
•  Check the propeller blades for damage.

AFTER EACH USE

• Disconnect the battery cables from the power source.
•  Check the propeller and the propeller shaft for debris such as weeds and fishing line. Remove all debris.
•  Rinse the trolling motor with clean water to remove dirt and dust that may scratch the surface.
•  Periodically lubricate all the pivot points. Refer to Lubricating the Pivot Points.
•  Check the tightness of bolts, nuts, and other fasteners.
•  Inspect the battery. Refer to Battery Inspection.

STORAGE PREPARATION
The major consideration in preparing the trolling motor for storage is to protect it from corrosion and damage caused by freezing of trapped water.
Complete the appropriate care instructions to prepare the trolling motor for storage. Store the trolling motor in a dry location where it will not be affected by temperatures below ‑29 °C (‑20 °F).

IMPORTANT: Trolling motors stored in temperatures below 0 °C (32 °F) should be operated slowly for a minimum of 15 minutes before going above 30% operation.

Lubricating the Pivot Points
To reduce friction, lubricate the following pivot points periodically:

•  Pivot pin
•  Latch pin
•  Tilt positioning pin/lever
•  Tilt positioning pin/lever spring

IMPORTANT: Never use an aerosol lubricant to grease or oil any part of the unit. Many aerosol lubricants contain harmful propellants that can cause damage to various parts of the trolling motor.

Battery Inspection

The battery should be inspected at periodic intervals to ensure proper trolling motor operation.
IMPORTANT: Read the safety and maintenance instructions that accompany your battery.

1. Ensure that the battery is secured to the vessel.
2. Ensure that the battery cable terminals are clean, tight, and correctly installed. For installation instructions, refer to Battery Connection.
3. Ensure that the battery is equipped with a battery box to prevent accidental shorting of the battery terminals.

IMPORTANT: Remove the propeller nut with a prop wrench. Using another tool may damage the propeller nut or shaft. If the propeller cannot be removed easily, use a rubber mallet to lightly tap the back side of the opposite blade. If the propeller cannot be removed, have the propeller removed by an authorized dealer.
NOTE: If the propeller pin is bent, replace the propeller pin.

•  Propeller pin
•  Propeller
•  Propeller nut
•  Prop wrench

INSTALLING THE PROPELLER

1.  Rotate the motor shaft to insert the propeller pin horizontally.
2.  Install the propeller onto the motor shaft by engaging the propeller onto the propeller pin.
3.  Install the propeller nut. Tighten the propeller nut securely.
4.  Use the prop wrench to tighten the propeller nut another ¼ turn.

MotorGuide Accessories Inquiries
Refer to www.motorguide.com for factory- authorized accessories for all MotorGuide trolling motors.

TROUBLESHOOTING

Trolling Motor Performance

Loss of power

| Weak battery| Refer to Wiring and Battery Information.
Loose or corroded battery connections
Propeller is loose, damaged, or off‑balance| Refer to Maintenance.

Wiring or electrical connection faulty

| Wire gauge from the battery to the trolling motor is insufficient. Six‑gauge wire is recommended.
Weeds, fishing line, or debris wrapped around propeller| Remove weeds, fishing line, or debris from propeller.

Excessive noise, vibration

| Motor shaft is bent| Refer to Warranty Information.
Propeller is loose, damaged, or off‑balance| Refer to Maintenance.

Motor failure (all speeds)

| Weak battery| Refer to Wiring and Battery Information.
Loose or corroded battery connections

Electrical

| Check the connector for a loose or damaged connection. Refer to Wiring and Battery Information.

Fuse on circuit breaker is open

| Replace the fuse or reset the circuit breaker only after determining the root cause of the problem.

Motor failure (one or more speeds)

| Propeller is loose, damaged, or off‑balance| Refer to Maintenance.
Wiring or electrical connection faulty.| Refer to Warranty Information.
Symptom| Possible Cause| Resolution
---|---|---

Difficulty removing propeller

|

Bent propeller pin

| Hold one blade and lightly tap the opposite blade with a rubber mallet.
Use a putty knife on both sides of the propeller to apply equal pressure.
Bent armature shaft| Refer to service center.

OWNER SERVICE ASSISTANCE

Mercury Marine Service Offices
For assistance, call, fax, or write. Please include your daytime telephone number with mail and fax correspondence.

United States, Canada|
---|---
Telephone| English +1 920 929 5040

Français + 905 636 4751

| Mercury Marine W6250 Pioneer Road|
P.O. Box 1939

Fond du Lac, WI 54936-1939

|
Fax| English +1 920 929 5893

Français +1 905 636 1704

|
Website| www.mercurymarine.com|
Australia, Pacific|
---|---
Telephone| +61 3 9791 5822| Brunswick Asia Pacific Group|
41–71 Bessemer Drive|
Fax| +61 3 9706 7228|
Dandenong South, Victoria 3175|
Australia|
Europe, Middle East, Africa|
---|---
Telephone| +32 87 32 32 11| Brunswick Marine Europe|
Parc Industriel de Petit-Rechain|
Fax| +32 87 31 19 65|
B-4800 Verviers,|
Belgium|
Asia, Singapore, Japan|
---|---
Telephone| +65 65466160| Brunswick Asia Pacific Group|
T/A Mercury Marine Singapore Pte Ltd|
Fax| +65 65467789|
29 Loyang Drive|
Singapore, 508944|

References

• Home
• MotorGuide - Home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>