BOLY SG2060 Trail Camera User Manual

Trail Camera
SG2060 Series

Getting Started

night option
Sharp Technology

Camera Operation

2.1 Batteries/ Power Supply
The camera is powered by eight AA batteries. High-density, high-performance, rechargeable alkaline or NiMH batteries are recommended, all batteries must be 1.5V. When the batteries are low, the camera will automatically shut down.
A DC 6V/2A external power supply adapter (not included) can also, be used to power the camera.
2.2 SD Card Information
Insert the SDcard into the camera before turning on the camera.
This camera supports up to a 64GB capacity SD card and has no built-in internal memory. The camera will not function without the SD card properly inserted into the camera.
Make sure the SD card is unlocked before inserting it into the camera.
The camera will operate properly with a locked SD card inserted, but the card will not be able to store captured images or videos taken by the camera.
Do not remove the SD card while the camera is on.
Removing the SD card while the camera is on risks damaging the internal components of the camera.
If you experience any problems with an inserted SD card, try reformatting the SD card using the camera’s main settings option.

2.3 Camera Mode
ON Mode
The camera will capture pictures or videos when motion is detected and/or at specific time intervals, according to the programmed settings. After switching the camera to the ON position, the motion indicator LED(red) will blink for about 10 seconds and then turn off. This delay time allows you to adjust the camera position if needed before the camera becomes active.
SETUP Mode
Customize the camera settings, or playback pictures and videos the camera has taken on the LCD display.
OFF Mode
Turns off the camera. The camera will still consume a small amount of battery power while in the OFF mode. It is recommended to remove the batteries if the camera will not be used for a long period of time.
2.4 Trigger Mode
PIR Triggering: The default setting is on. If PIR Triggering is on, the camera is only active when motion is detected. If PIR sensitivity is set to OFF, the camera stops responding to the motion.
Timer Triggering: The default setting is OFF, which means timer triggering is disabled. When the timer triggering interval is set to a non-zero value, the camera starts to work at a preset interval. Users need to set the PIR sensitivity to OFF if they want the camera to work only at preset intervals.
PIR and Timer Triggering: For both PIR triggering and Timer triggering, users need to set PIR sensitivity to low, normal, or high according to the external environment, and set the Timer interval to a desired non-zero value. The camera will capture pictures or videos in a preset time interval even if there is no motion detected. The camera will also capture pictures and videos if motion is detected.

Camera Setup Settings and Display

3.1 Settings Interface & Display
To update the camera settings, move the power switch to the SETUP position.
Menu: Enter the program menu in preview mode
: Exchange between playback and preview mode
DEL: Delete a photo or video
: Capture a photo or record a video manually
▼▲►◄: Navigate parameter settings
OK: Save parameter settings and play videos
When the camera is in SETUP mode, the screen will activate and display the following:
3.2 Manual Image / Video Capturing
Place the camera in SETUP mode and press  to manually capture photos or record video. Press  again to stop capturing.
3.3 Manage Images and/or Videos
Place the camera in the TEST/SETUP mode and press the button to view images or videos. The latest image or video will be shown on the LCD screen.
To view:
Press ▲ or ▼ to view the previous or next image/video, press to play a video.
To delete:
Press DEL to delete images or videos in the playback state. If you are in the preview state, press to enter into playback state first.
3.4 Camera Setup Operation
To view the camera settings menu, slide the power switch to the setup position. Use the ▼or ▲ buttons to select sub-menus; use ◄ or ► to select different options. Press OK to save the settings. After changing EACH setting in the Setup menu, press OK or the camera will not keep new settings.
Depending on the different models, not all menu options may be available on your specific camera.

Photo: to take photos.
Video: to capture video.
Pic+Video: to take a picture with a video
| clip. This mode disables the photo burst function. Default: Photo
---|---
Set Clock| To set the camera’s clock. The clock format is YY/MM/DD hour minute: second. Press ♦ ♦ to change the value. Press ► Ito select date or time field.
Photo Size| Choose the image size,e.g.48MP,36MP,16MP. Default:36MP
Photo Burst| Choose the number of continuous photos taken after each trigger. When the Camera Mode is set to Pic+Video, the Photo Burst option is automatically disabled, resulting in only one picture captured with the video. When the Camera Mode is set to Photo, the Photo burst option will operate normally as specified. Default:1
Video Size| Choose the video size: 1920×1080,1280×720 or 640×480)
| Default:1920×1080
---|---
Video Length| Choose the duration of video recordings. This parameter is only active and adjustable when the device is in video mode and ON. Press▼▲ to decrease or increase the value. Its value extends from 5 to 90 seconds(for SG2060 Series). Default:10Sec
Time Lapse| If time-lapse is on, the camera can capture images or videos at a preset time interval regardless of whether a motion is detected. The default setting is off, which means the timer function is disabled. Changing this parameter to a non-zero value turns on the Time Lapse mode, and the camera will take photos at the given time interval.NOTE: If the PIR Trigger is set to off, then Time Lapse can’t be set to off. Default: OFF
PIR Trigger / PIR Sensitivity| This parameter defines the sensitivity of the PIR High: and indicates that the camera is more responsive to motion. It is recommended to use high sensitivity in a room or environment with little interference. Normal: The default value is normal. Low: means the camera is not very responsive to motion. It is recommended to use this setting in outdoor environments or environments with a lot of interference like wind, smoke, near a window, etc. OFF: the camera is not triggered by motion to capture pictures or videos. NOTE: The sensitivity of the PIR is strongly related to the temperature. A higher temperature leads to a lower sensitivity. Therefore, it is suggested to use higher sensitivities for high-temperature
---|---
| environments. Default: Normal
PIR Interval| This setting indicates how long the PIR sensor will be disabled after it is triggered. During this time the PIR sensor will not react to any detected motion or scheduled timer functions. The PIR Interval can be set between zero seconds to a maximum of 1 hour. Press LEFT or RIGHT to decrease or increase the desired PIR Interval time. Default:5Sec
Picture Type| Choose the type of flash for night photography: Black&White means select 940nm led, Colour is selected whtie led or Xenon, (Available for SG2060-T) Default: Black&White
Work Day| Choose the days of the week the camera works on. Not available for SG2060 Series.
Default: All
Work Hour| This setting controls when the camera is active each day. If activated, the camera will NOT take pictures or videos outside of the specified working hour, regardless of any other setup option settings. The values are set to military time which ranges from 00:00 to 23:59. Default: OFF
Camera Position| You can set an A-Z indicator for each of your cameras in order to distinguish which photos are from a specific camera.
Default: OFF
Time Stamp| It defines whether the date and time should be stamped on the video or not.
Default: On
Language| Choose the language for the menu.
Beep Sound| Enable or disable the beep sound. Available for SG2060series
Default: On
Recycle Storage| In hunting mode, when the SD card is full, the first images or videos will be replaced by new pictures or videos. This allows you to capture more without the need to retrieve your memory card manually. In SETUP mode, the SD card can’t recycle storage.
Default: Off
Format SD| Deletes all images and videos on the SD card. Make sure to make a backup of important data before selecting this option.
Default Settings| Restore all camera settings to default values.
Version| It contains version information.

Troubleshooting

PIR Detection Zone

This camera has a new PIR, which is patented. The new PIR’s detection range can reach 100ft. in good environments. The following picture compares the detection zone between the normal and new PIR. The PIR detection angle (α) is smaller than the field of view (FOV) angle (β). The advantage of this design is to reduce the empty picture rate and capture most, if not all, motions.

Technical Specifications

Parts List

Version 4.2

Documents / Resources

| BOLY SG2060 Trail Camera [pdf] User Manual
SG2060, Trail Camera, SG2060 Trail Camera, Camera
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>