HAMPTON BAY 93400 LED CCT Low Voltage Spot Light User Manual
- June 3, 2024
- HAMPTON BAY
Table of Contents
HAMPTON BAY 93400 LED CCT Low Voltage Spot Light User Manual
PACKAGE CONTENTS
Assembly and Installation
WARNING: Risk of electric shock. Do
not install the light within 10 ft. (3.05 m) of a pool, spa or fountain
NOTE: Never push the fixture into the
ground by the lamp body. Do not use a hammer. If the ground is hard, use water
to soften it or a trowel to loosen the soil.
- Insert the fixture wire on the wire connector (C) into the groove located on the top of the ground stake (B).
- Attach the lamp body (A) onto the top of the ground stake (B). Ensure the fixture wire on the wire connector (C) stays centered on the groove of the ground stake (B) to avoid damage to the fixture wire.
- Prepare a hole where installation will be located. Make sure hole is not larger than the stake (B).
- Install the fixture in the ground by pushing on the foot step (1) on the stake (B). Do not push down on the lamp body (A).
- Rotate the knob on the side of the lamp body (A) to adjust your light up or down.
- Choose your desired Correlated Color Temperature (CCT) by rotating the knob behind the lamp body (aa) clockwise or counter-clockwise to choose one of the three options available; 2700K warm white, 3000K warmest white, or 4000K bright white.
Connecting the wires
WARNING: The wire connector contacts (C) have sharp edges for piercing the
main low voltage cable. To avoid injury, do not touch the metal contacts
CAUTION: The wire from the low voltage power unit shall be 12-16 AWG type
underground Low Energy Circuit Cable.
IMPORTANT : Protect the wiring by routing it in close proximity to the
light or next to a building structure such as a house or deck.
Do not bury the wiring by more than 6 in. (15.24 cm) in order to connect to
the main secondary wire.
Do not submerge fixtures in water.
- Detach and place the wire connector (C) on opposite sides of the low voltage cable (not included) where the fixture will be
- Align and fit the main low voltage cable vertically in the slot of the wire connector as
- Press the wire connector (C) together until it is fully seated and locked around the Pre-set prongs will pierce the cable insulation and establish contact. Turn on the power unit. If the light fixture does not turn on, repeat operations 2 and 3.
Once the clip-on connector is in place, we recommend wrapping it in electrical tape (not included) for additional protection
Cable Selection
| 12 VOLT TAP | Cable Length |
|---|---|
| Total Fixture Wattage | 0-50 feet |
feet**
0-60 Watts| 16 AWG| 16 AWG| 14 AWG
61-120 Watts| 16 AWG| 14 AWG| 12 AWG
121-180 Watts| 14 AWG| 12 AWG| NOT RECOMMENDED
181-240 Watts| 14 AWG| 12 AWG| NOT RECOMMENDED
241-300 Watts| 12 AWG| NOT RECOMMENDED| NOT RECOMMENDED
600W Transformer = (2×300 Watts)| 12 AWG| NOT RECOMMENDED| NOT RECOMMENDED
900W Transformer = (3×300 Watts)| 12 AWG| NOT RECOMMENDED| NOT RECOMMENDED
NOTE : Most LED landscape fixtures can operate with full illumination from 9V all the way to as little as 6V. It is possible to have extended length runs with LED fixtures that go beyond the specifications shown on the charts above.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| The lights do not turn on. | □ There is no power. |
□ There is a disconnection or break in the wire.
□ The transformer setting is incorrect.
| □ Check the outlet and ensure that a breaker or GFCI circuit has not been tripped.
□ Follow the wires from the fixture and ensure a continuous connected path back to the transformer.
□ Check the settings on the transformer.
The lights flicker.| □ There is a loose wire connector to the fixture.| □
Tighten the wire connector and ensure the metal contacts pierce the insulation
on the low voltage cable from the transformer.
The lights flicker (all fixtures).| □ There is a loose connection at the
transformer.| □ Unplug the transformer from the outlet and visually inspect
the positive and negative connecting posts. Each wire should be securely
screwed in and not in contact with any other.
Care & Cleaning
- Before attempting to clean the fixture, disconnect the power to the fixture by turning the breaker off or removing the fuse from the fuse
- To clean the fixture, use a dry or slightly dampened clean
- Do not use cleaners with chemicals, solvents, or harsh abrasives, as damage to the fixture may
Warranty
WHAT IS COVERED
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of five (5) years from date of purchase. This warranty applies only to the original consumer and only to products used in normal use and service. If this product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect, or mishandling.
WHAT IS NOT COVERED
This warranty shall not apply to any product that is found to have been
improperly installed, set-up, or used in any way not in accordance with the
instructions supplied with the product. This warranty shall not apply to a
failure of the product as a result of an accident, misuse, abuse, negligence,
alteration or faulty installation, or any failure not relating to faulty
material or workmanship. The warranty shall not apply to the finish on any
portion of the product, such as surface and/or weathering, as this is
considered normal wear and tear.
The manufacturer does not warrant and specially disclaims any warranty,
whether express or implied, of fitness for a particular purpose, other than
the warranty contained herein. The manufacturer specifically disclaims any
liability and shall not be liable for any consequential or incidental loss or
damage, including but not limited to any labor/expense cost involved in the
replacement or repair of said product.
Contact the Customer Service team at 1-855-HD-HAMPTON or visit www.HamptonBay.com