ASPL-3028-X-XX AMP Low Voltage Landscape Lighting Installation Guide
- June 3, 2024
- VOLT
Table of Contents
- Important Safety Instructions: Read Before Installation !
- Important Safety Instructions !
- Package Contents
- Parts Required
- Product Dimensions
- 1 Test Solar Light
- 2 Install Riser
- 3 Install Stake
- 4 Install Riser to Stake
- How to Replace Battery
- 1 Remove Shield
- 2 Remove Luminaire
- 3 Remove Circuit Board
- 4 Remove Circuit Board
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ASPL-3028-X-XX AMP Low Voltage Landscape Lighting Installation Guide
Important Safety Instructions: Read Before Installation !
This luminaire is intended for installation in accordance with local codes and the National Electric Code (NEC). Failure to adhere to these codes and instructions may result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, operation maintenance or mounting situations.
Please note that these solar fixtures are equipped with built-in photocells, so they will not turn on until it is dark enough. These fixtures will also require plenty of sunlight to function properly. It’s best to have the fixture in an area where the sun will get to it at all times throughout the day and where no ambient lighting will affect the photocell at night. If your fixture is not functioning at night, be sure that the on/off button has been engaged. See step one for details.
Important Safety Instructions !
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
- Lamp gets HOT quickly!
- Do not touch the hot lens, guard or enclosure.
- Keep lamp away from materials that may burn.
- Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage lamp.
- Do not operate the luminaire fitting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
Package Contents
A. (1) Fixture Body
Parts Required
A. Riser
B. Mounting Accessory
Product Dimensions
1 Test Solar Light
Slide the ON/OFF switch of the fixture to the “ON” position. Cover solar
panels completely by using black materials. The fixture will
light up when the solar panel is covered and turn back off when it is
uncovered.
Now you can proceed to next steps of installations knowing the fixture is in ON mode.
2 Install Riser
Thread the riser onto the fixture and hand tighten until snug.
3 Install Stake
Determine the desired location for mounting the stake mount. Hammer the stake into the ground until flange of stake is flush to grade. To avoid damage to the stake, place a board on top of the stake while hammering.
Note: If the ground is hard and the stake is difficult to install, make a crosscut in the ground using a flat shovel.
4 Install Riser to Stake
How to Replace Battery
1 Remove Shield
Press the sides of the shield to remove it from the fixture body.
2 Remove Luminaire
Using a screwdriver, remove the 3 screws. Then take the light source out of the hat.
3 Remove Circuit Board
Remove the battery cover from the luminaire by using a screwdriver and removing the screws.
4 Remove Circuit Board
Disconnect the quick connector by pressing the tabs on the side. Remove the old battery by removing the two screws. Replace the battery and secure it with the previously removed screws. Then connect the tabs of the quick connector back together.
Reinstall the solar panel to the fixture body and secure with previously removed screws.
customersupport@amplighting.com
813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
Specifications and product details subject to change without notice.
© Copyright 2021, AMP® Lighting, Lutz FL USA 33549 • All rights reserved.
customersupport@amplighting.com •
813.978.3900
IS-ASPL-3028-ver2.pdf
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>