VAL-180 Series Low Voltage Landscape Lighting, Top Scotty Spotlight Instruction Manual
- June 3, 2024
- VOLT
Table of Contents
180 Series Low Voltage
Landscape Lighting, Top Scotty Spotlight
Instruction Manual
**** Important: Please Read Before Installation
This luminaire is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
- Make sure the power is turned OFF before installing or servicing this luminaire.
- WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more from pool, spa or fountain.
- This luminaire is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
- Wiring connections must be made with UL Listed wire connectors that are suitable for outdoor use.
- Position the low voltage wire and wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire or fitting.
- The main low voltage cable is intended for shallow burial – less than 6 inches (152 mm).
- If additional lengths of low voltage cable are required, please contact www.voltlighting.com or call 1-813-978-3700.
**** IMPORTANT SAFETY INFORMATION
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS Lighted
lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
- Turn off/unplug and allow to cool before replacing lamp.
- Lamp gets HOT quickly! Contact only switch/plug when turning on.
- Do not touch the hot lens, guard or enclosure.
- Keep lamp away from materials that may burn.
- Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage lamp.
- Do not operate the luminaire fitting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
Package Contents
A. (1) Fixture
B. (1) Stake
Product Dimensions
Install Stake Determine the desired location for
mounting the luminaire. Hammer the stake into the ground until flange of stake
is flush to grade. To avoid damage to the stake, place a board on top of the
stake while hammering.
NOTE: If the ground is hard and the stake is difficult to install, make a
crosscut in the ground using a flat shovel.
Install Luminaire to Stake
Clear away an area in the
ground at the wireway slot on top of the stake. Lay the luminaire pigtail into
the wireway slot and attach the luminaire onto the stake. Tighten until snug.
Wire Connections
Strip both leads from the
luminaire pigtail. Using two wire connectors (sold separately), connect the
leads from the luminaire to the main supply cable leads.
Install Bulb
Insert the bulb with the
correct wattage and type marked on the luminaire label.
CAUTION: Do not exceed maximum wattage marked on luminaire label.
NOTE: DO NOT touch bulb with bare hands. Use soft cloth to handle bulb.
Install Lens
Thread
the lens onto the luminaire and hand tighten until snug.
Install Glare Guard
Install/Replace Bulb
Loosen the lock screw to remove the glare guard. Then remove the lens to
expose the bulb. Replace it with the correct wattage and type marked on the
fixture label. Then reinstall the lens and glare guard.
IMPORTANT: Bulbs must be protected from moisture and dust at all times.
Always reinstall lens when removed.
Help Hotline:
1-813-978-3700
Mon-Fri 8am-8pm
Sat-Sun 10am – 6pm (EST)
www.voltlighting.com
Specifications and product details subject to change without notice.
© Copyright 2022, VOLT®
Lighting, Lutz FL USA 33549 • All rights
reserved.
customersupport@voltlighting.com
813.978.3700
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>