VAL-1183 Low Voltage Landscape Lighting Instruction Manual
- May 15, 2024
- VOLT
Table of Contents
INSTALLATION INSTRUCTIONS
VOLT® LOW VOLTAGE LANDSCAPE LIGHTING
VO LT ® Top Dog Scotty Mini Brass Spotlight
ITEM: VAL-1183
1-813-978-3700 • Mon-Fri 8am-8pm
Sat-Sun 10am – 6pm (EST)
VAL-1183 Low Voltage Landscape Lighting
IMPORTANT: PLEASE READ BEFORE INSTALLATION
This luminaire is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situation.
- Make sure that the power is turned OFF before installing or servicing this luminaire.
- WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more from pool, spa or fountain.
- This luminaire is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
- Wiring connections must be made with wire connectors that is suitable for outdoor use.
- Position the low voltage wire and wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire or fitting.
- The main low voltage cable is intended for shallow burial – less than 6 inches (152 mm)
**** IMPORTANT SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
- Turn off/unplug and allow to cool before replacing lamp.
- Lamp gets HOT quickly! Contact only switch/plug when turning on.
- Do not touch the hot lens, guard or enclosure.
- Keep lamp away from materials that may burn.
- Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage lamp.
- Do not operate the luminaire fitting with a missing or damage shield.
SAVE THESE INSTRUCTIONS
PACKAGE CONTENTS
A. Fixture
PRODUCT DIMENSIONS
1. INSTALL STAKE
Determine the desired location for mounting the stake mount. Hammer the stake
into the ground until flange of stake is flush to grade. To avoid damage to
the stake, place a board on top of the stake while hammering.
Note: If the ground is hard and the stake is difficult to install, make a
crosscut in the ground using a flat shovel.
2. INSTALL FIXTURE BODY TO STAKE Clear away area in the ground at the
wireway slot on top of the stake. Lay the luminaire pigtail into the wireway
slot and tighten fixture on to stake.
3.Wire Connections Strip both leads from the luminaire pigtail. Using two
wire connectors (sold separately), connect the leads from the luminaire to the
main supply cable leads.
4 .Install Lamp
Insert the lamp (sold separately), with the correct wattage and type marked on
the luminaire label.
CAUTION: Do not exceed maximum wattage marked on luminaire label.
NOTE: DO NOT touch lamp with bare hands. Use soft cloth to handle lamp.
5. INSTALL LENS Thread the lens onto the luminaire and hand tighten
until snug.
6. Install Glare Guard Place the glare guard over the lens and secure
with the set screw.
Adjust the luminaire to the desired angle by using the knuckle.
Install/ Replace Lamp
Loosen the set screw and remove the lens and glare guard to expose the lamp.
Replace it with the correct wattage and type marked on the luminaire label.
Then reinstall the lens and the glare guard.
IMPORTANT: Halogen lamps must be protected from moisture and dust at all
times. Always reinstall lens when removed.
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-
Sun 10am – 6pm (EST)
Specifications and product details subject to change without notice.
© Copyright 2023, VOLT
Lighting, Lutz FL USA 33549 • All rights reserved.
customersupport@voltlighting.com
www.voltlighting.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>