TOTAL TG1091156 Electric Grinder Instruction Manual

TOTAL TG1091156 Electric Grinder

Security instructions

Caution
Read all safety warnings and all instructions. Failure to follow all warnings and instructions may result in electrical shock, fire, and/or serious injury. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

Note: Save all warnings and instructions for future reference.

1. Work area safety
   • a. Keep the work area clean and well lit to prevent accidents.
   • b. Do not use power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust that can cause fires.
   • c. Keep children and other unauthorized persons away while using a power tool. Distractions can cause you to lose control of the tool.
2. electrical safety
   • a. Power tool plugs must match the outlet. Never modify the plug in any way. Using a suitable plug reduces the risk of electric shock.
   • b. Avoid bodily contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded.
   • c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electrical shock.
   • d. Never use the cord to carry, pull or unplug the power tool. Keep the cable away from heat or oil.
   • e. When using a power tool outdoors, use an extension cord suitable for outdoor use.
   • f. If using the tool in a damp location is unavoidable, use a Residual Current Device (RCD) protected supply to reduce the risk of electric shock.
3. Personal security
   • a. Always stay alert, watch what you are doing and use common sense when using the tool.
   • b. Do not use a power tool if you are tired or under the influence of medication or other substances.
   • c. Wear personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-slip safety shoes, hard hat, or hearing protection used in the proper conditions will reduce personal injury. Also don’t wear loose clothing or jewelry.
   • d. Prevent the tool from turning on unintentionally. Make sure the switch is in the off position before connecting to power source and moving.
   • e. Remove any adjusting wrenches or wrenches before turning on the power tool. An adjustable wrench or wrench placed in a rotating part of the power tool can cause serious injury.
   • f. If devices are used for dust extraction and collection, make sure they are properly connected. Properly use these devices and you will reduce dust-related hazards.
4. Use and care of power tools
   • a. Do not force the tool. Use the correct power tool for each use.
   • b. Do not use the power tool if its power switch does not work. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
   • c. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool to avoid accidental starting.
   • d. Use the power tool, accessories and bits etc. in accordance with these instructions, taking into account the working conditions and the work to be carried out. Using the power tool for operations other than those intended could result in a hazardous situation.
   • e. Store power tools out of the reach of children and do not allow people unfamiliar with the tool to use it.
   • f. Carry out regular maintenance on power tools. Check for misalignment or binding of moving parts, breakage of parts, and any other conditions that may affect the operation of power tools. If it is damaged, have the power tool repaired before using it. Many accidents are caused by poorly maintained power tools.
   • g. Keep accessories clean and sharp, as with proper maintenance they are less likely to bind and are easier to control.
5. Service
   • a. Have your power tool serviced by a qualified person and use replacement parts recommended by the manufacturer. This will ensure that the safety of the power tool is maintained.

Safety rules for correct use

• Double insulation for additional protection
• Please read the instruction manual before use.
• CE conformity.
• Wear safety glasses, hearing protection and a dust mask.
• Waste electrical products must not be disposed of with household waste. Please recycle at the appropriate facilities. Check with your local authority or retailer for recycling advice.
• Security alert. Use only accessories supported by the manufacturer.

Additional security warnings

Grinding, sanding, wire brushing, polishing or abrasive cutting operations
This power tool is designed to function as a grinder, sander, planer, wire brush, polisher, or cutting tool.
Read all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow all instructions may result in electrical shock, fire, and/or serious injury.

• Do not use this tool in operations for which it was not designed. Otherwise, it may create a hazard and cause personal injury.

• Do not use accessories and fixtures or tools that are not specifically designed and recommended by the tool manufacturer. The fact that the accessory can be attached to the power tool does not guarantee safe operation.

• The rated speed of the blade must be at least equal to the maximum speed marked on the power tool. A tool that has a higher speed than the tool can eject it from its clamping.

• The outside diameter and thickness of the disc must be within the rated capacity of your guards. Improperly sized accessories cannot be properly stored or controlled.

• The assembly of threaded tools must coincide with the thread of the spindle of the grinder. For flange mounted fittings, the fitting hole must fit the mounting diameter of the flange.

• Do not use the damaged cutting tool. Before each use, check the cutting discs, make sure they do not have cracks, tears or excessive wear; check wire brush for loose or cracked wires. Dull bits cause the tool to strain too much. If the power tool is dropped, inspect for damage and replace if necessary.
  After inspecting and installing a tool, stand in a safe area and check that no one is in the work area when you run the power tool at full speed with no load for one minute. Damaged accessories will normally break during this testing time.

• Wear personal protective equipment. Wear face shield, safety glasses. If necessary, dust masks, ear protectors, gloves and workshop apron capable of stopping small abrasive or chip fragments. Eye protection must be capable of stopping debris and flying particles generated by various operations. The dust mask or respirator must be capable of filtering the particles generated by your operation. Prolonged exposure to high intensity noise can cause hearing loss.

• Keep people out of the work area. Anyone entering the work area must wear personal protective equipment. Fragments of the workpiece or a broken accessory can break loose and cause injury beyond the immediate area of operation.

• Hold the power tool by insulated gripping surfaces only, when performing an operation where the tool or cutting tool may come into contact with cables and/or pipes (including its own cable). It may cause an accident or electric shock to the operator.

• Position the tool cable away from the rotating tool. If you lose control, the cable may be cut or snagged causing serious accidents.

• Never let go of the power tool until the cutting tool has come to a complete stop.

• Do not operate the power tool while carrying it by your side. Accidental contact with the disk could snag her clothing, pulling it closer to her body.

• Periodically clean the vents on the tool. The motor fan will draw dust into the casing and excessive accumulation of powdered metal can cause electrical hazards.

• Do not use the power tool near flammable materials. Sparks could ignite these materials.

• Do not use tools or cutting tools that require coolant. The use of water or other liquid coolants may result in electrocution or electrical shock.

Rollbacks and Related Warnings
Kickback is a sudden reaction when a blade, backing pad, brush, or other cutting tool binds or snags. Binding or snagging causes a rapid lockup of the disc which, in turn, causes the uncontrolled power tool to be forced in the opposite direction of tool rotation.

Kickback is the result of power tool misuse and/or incorrect procedures or conditions. This can be avoided by taking the proper precautions.

• Keep a firm grip on the power tool to allow it to resist kickback forces. Always use the auxiliary handle, if provided, for maximum control over kickback or torque reaction during start-up. Torque reactions or kickback forces can be controlled by the operator if proper precautions are taken.
• Never put your hand near the running cutting tool. The cutting tool can kick back on your hand.
• Do not position your body in the area where the power tool will move if kickback occurs. Kickback will propel the tool in the opposite direction of wheel motion at the point of contact.

Abrasive grinding and cutting operations

• Use only the types of wheels that are recommended for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately covered and are unsafe.
• The cutting surface of depressed center abrasive wheels should be mounted below the plane of the guard cutting edge. An incorrectly mounted wheel that protrudes beyond the plane of the guard edge cannot be adequately protected.
• The guard must be firmly attached to the power tool.
• Discs should only be used for recommended applications.
• Always use the proper flanges for the correct size and design of discs. Flanges for cutting wheels may be different from flanges for grinding wheels.
• Do not use worn wheels from larger power tools. The blade intended for a larger power tool is not suitable for the higher speed of a smaller tool.

Abrasive cutting operations

• Do not “jam” the disc or apply excessive pressure. Overloading the disc increases susceptibility to binding and the possibility of kickback or breakage.
• Do not place the body near the cutting area of the disc. When the wheel locks up at the point of contact and in the event you stomp, that kickback will direct the tool toward your body.
• When the blade jams for any reason, turn off the tool and hold it still until it comes to a complete stop. Never try to remove the cutting disc by turning the tool on again, otherwise kickback may occur. Investigate and take corrective action to eliminate cause of stall.
• Do not restart the cutting operation on the work piece. Let the blade come up to full speed and carefully recut. The wheel can bind, ride up, or kick back if the power tool is restarted on the work piece.
• Any large work piece should be clamped with the proper clamps to minimize the risk of binding. Supports, clamps, “C” clamps, clamps or “F” clamps must be placed on the edges of the workpiece at a safe and prudent distance from the line of cut or gouging to be made.
• Use extreme caution when making a “pocket cut” in existing walls or other blind areas. It may cut gas or water pipes, electrical wiring, or objects that can cause kickback.

Sanding operations

• Do not use oversized discs. Follow the manufacturer’s recommendations when selecting sandpaper. Sandpaper that extends past the sanding pad presents a hazard and can cause binding and kickback.

Polishing operations

• Do not allow the residue of any polishing flecks to spin freely. Please remove or clip them because otherwise they may harm the work or your own body.

Wire brushing operations

• Please note that the brush sheds wire bristles even during normal operation. Do not overload the cables by applying excessive load to the brush. Wire bristles can easily penetrate light clothing and/or skin.
• The use of a wire brush guard is recommended. The wire wheel or brush may expand in diameter due to work load and centrifugal forces.

Other risks

Even when the power tool is used as prescribed, it is not possible to eliminate all residual risk factors:

• a. Health defects resulting from vibration emission if the power tool is used for a longer period of time or if it is not managed and maintained properly.
• b. Injuries and property damage due to broken fixtures breaking suddenly.

Caution

• This power tool produces an electromagnetic field during operation. This field can, in some circumstances, interfere with active or passive medical implants.
• To reduce the risk of serious injury, we recommend that persons with medical implants consult their physician before using this power tool.

If the cable is damaged or cut during work, do not touch the cable, immediately unplug the tool. Never use the machine with a damaged cable. The machine must not be damp and must not be used in a humid environment.

Attention: Safe operation of this machine is only possible when the operating or safety information is fully read and the instructions contained therein are strictly followed.

Technical data

Product Description

1. Spindle lock button
2. On/off switch
3. Casing
4. Power cord sheath
5. Ventilation openings
6. Auxiliary handle
7. Disc guard
8. Rotation indicator direction
9. Thread lock flange
10. Mounting washer flange

Note 2: Not all accessories illustrated or described need to be included in the standard delivery.

Set up

Mounting

Installation of the auxiliary handle The auxiliary handle can be placed in both positions of the gearbox.
If you are right-handed, adjust the handle as shown in the figure. If you are left-handed, adjust the handle in the opposite direction. When using a cut-off wheel, you can screw the handle to the top of the gearbox.

NOTE: This handle must be used at all times to maintain full control of the tool.

Blade Guard Adjustment
Adjust the guard to protect your hands and to control the orientation of sander debris.

• Loosen the screw.
• Position the protector at the desired angle.
• Tighten the screw.

Attention: Make sure the guard is in place before starting the grinder. Never use it without the blade protector.

Mounting of the discs

• Place the grinding/cutting wheel on top of the inner flange and over the spindle. Make sure it is firmly seated on the raised section of the inner flange.
• Place the outer flange over the disc, making sure that the raised side is facing towards the disc and that it is fully seated in the center hole of the disc.

NOTE: When clamping thin section metal diamond blades, the outer flange must be reversed so that the flat/concave side bolts against the hub of the blade. Press and hold the spindle lock button and tighten the outer flange with the two-prong torque wrench. It may be necessary to rotate the spindle to fully locate the spindle lock button.

When the outer flange washer is tight, release the spindle lock button and remove the key.

switch
The on/off switch is in the “OFF” position. The angle sander is started by pushing the on/off switch forward. To stop the tool, release the ON/OFF switch and it will return to the “OFF” position.

Attention

• The disc will continue to spin for a few seconds after the angle sander has been turned off.
• Always wait until the wheel has come to a complete stop before setting the angle grinder down on a surface. Do not attempt to actuate the spindle lock button while the blade is still spinning.

To use the sander

Attention

• Do not turn sander on while disc is in contact with workpiece. Allow the drive to reach full speed before starting. Hold your angle grinder with one hand on the main handle and the other hand firmly around the auxiliary handle.
• Always position the guard so that as much of the exposed blade as possible is facing away from you. Be prepared for a series of sparks as the blade touches the metal.
• For best tool control, material removal and minimal overloading, maintain an angle between the wheel and the work surface of approximately 15°-30° during grinding and 10°-15° during sanding. Put light pressure on the abrasive discs for efficient operation. Pushing too hard will result in a drop in speed and overloading and motor damage may occur.
• Be careful when working in corners as contact with the intersecting surface can cause the tool to jump or twist. When grinding is complete, allow the workpiece to cool. Do not touch the hot surface.

Overload
Overloading will cause damage to the motor of your tool. This can happen if it is subjected to heavy use for long periods of time. In no case try to put too much pressure on your angle sander to speed up your work.

Abrasive discs work more efficiently when light pressure is exerted, thus avoiding a drop in speed. If your tool gets too hot, run it without load for 2-3 minutes until it has cooled down to normal operating temperature.

Work tips

• Your tool is useful both for cutting metals; for example, to remove screw heads, as well as to clean/prepare surfaces; for example, before and after welding operations.
• Different types of disc/cutter will allow the sander to meet various needs. Typically, grinding wheels/cut-off wheels are available for mild steel, stainless steel, stone, and brick. Diamond impregnated wheels are available for very hard materials.
• If the grinder is used on soft metals, such as aluminum, the disc may bind and will need to be replaced.
• At all times, let the sander do the work, do not force it or apply excessive pressure to the discs.
• If a slot is cut, make sure the cutter stays aligned with the slot, if you twist the cutter, the disc may break. If cutting a thin sheet, only allow the cutter to protrude through the material, excessive penetration can increase the chance of damage.
• In the case of cutting stone or brick, it is recommended to use a dust extractor. The electronic control allows a continuous preselection of the speed according to the material to be worked on. Constant electronic control maintains the preselected impact rate nearly constant between loaded and unloaded conditions.

Maintenance and troubleshooting

Maintenance
Make sure the tool is unplugged from power before performing any maintenance.

• Keep the ventilation slots clean and free of obstructions. If possible, blow compressed air into the vents to remove internal dust (safety glasses should be worn when doing this).
• Keep the outer casing of the tool clean and free of grease. Do not wash with water or use solvents or abrasives. Use only mild soap and a damp cloth to clean the tool. Never let liquid get inside the tool. Never immerse any part of the tool in liquid.
• Your angle grinder does not require additional lubrication.
• Always store your power tool in a safe, dry place.
• If you see some sparks flashing from the ventilation slots, this is normal and will not damage your power tool.

Problem solving
Although your new angle grinder is actually very simple to use, if you experience problems, check the following:

• If it is not working, check the power supply at the mains connection plug.
• If the disc wobbles or vibrates, check that the outer flange is tight; check that the disc is correctly positioned on the flange plate.
• If there are signs that the disc is damaged, do not use it as the damaged disc may disintegrate, remove it and replace it with a new one. Dispose of old discs correctly and responsibly.
• If working with aluminum or the like, the disc will soon clog and will not sand effectively.

Environment

• Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
• Contact your local authority for information on available collection systems.
• If electrical appliances are disposed of in landfills, hazardous substances can seep into the groundwater and enter the food chain, harming your health and well-being.
• Recycle raw materials instead of disposing of them as waste.
• The machine, accessories and packaging must be sorted for environmentally friendly recycling.

Exploded view

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>