Y Soft SAFEQ 6 USB Card Reader User Guide
- June 3, 2024
- Y Soft
Table of Contents
Y Soft SAFEQ 6 USB Card Reader
1 INTRODUCTION
PURPOSE OF THIS DOCUMENT
This document provides essential information on the installation and
configuration of YSoft USB Card Reader version 3.
VALIDITY OF THIS DOCUMENT
This document applies to YSoft USB Card Reader v3.
GOALS AND OBJECTIVES
That YSoft USB Card Reader v3 can be connected simply to a multi-functional
device and serve for user authentication using a card. The card must be
assigned to a user in the YSoft Safe system. After successful authentication,
the user can work the with device and perform their print, copy, or scan jobs
(depending on the device).
YSoft USB Card Reader v3 can also be connected to workstations and used with a
credit charger application or with the YSoft SafeQ client for authentication.
TERMS AND ABBREVIATIONS
- MFD -Multi-functional device
- USB Card Reader v3 -YSoft USB Card Reader version 3
PREREQUISITE KNOWLEDGE
The person installing USB Card Reader v3 must meet the following requirements:
knowledge of the YSoft SafeQ system (installation/administration/attendance)
DISCLAIMER
A user that makes changes or modifications not expressly approved by the party
responsible for compliance (Y Soft Corporation, a.s.) could void the uses
authority to operate the equipment.
Hereby, Y Soft Corporation, a.s. declares that the radio equipment type USB
Card Reader v3 is in compliance with Directive 2014/53/EU. The full text of
the EU declaration of conformity is available at the following internet
address https://www.ysoft.com/en/legal/european-union-declaration-of-
conformity.
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide
reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct
the interference at their own expense. This device complies with industry
Canada,s license-exempt RSSs. Operation is subject to the following two
conditions: (1) This device may not cause interference; and (2) This
device must accept any interference, including interference that may cause
undesired operation of the device.
The product conforms with directive 2002/96/EC of the European parliament and of the Council of 27 January 27, 2003 on waste electrical and electronic equipment (WEEE) and Directive 2003/108/EC of the European Parliament and of the Council of December 8, 2003 amending Directive 2002/96/EC on waste electrical and electronic equipment (WEEE).
OVERVIEW
SYSTEM OVERVIEW
YSoft SafeQ® USB Card Reader has the following characteristics:
- Connection and power supply of the card reader are via the USB host interface
- Exchange of the card reader is possible without turning off the MFD (hot-plug)
- Compatibility with some MFD additions
HARDWARE COMPONENTS
USB CARD READER SPECIFICATIONS
Parameter
| ****
Value
---|---
Identification
| ****
Using a card reader
Voltage
| ****
5 V DC
Maximum current input
| ****
0.5 A
Working temperature
| ****
+5°C to +35°C
Parameter
| ****
Value
---|---
Storage temperature
| ****
0°C to +50°C
Working air humidity
| ****
20% to 85% without condensation
Storage air humidity
| ****
8% to 85% without condensation
Resistance to magnetic field
| ****
no added resistance
Transmitting frequency
| ****
125 kHz, 132 kHz, 134.2 kHz, 13.56 MHz
USAGE
Please use the card by placing it on the edge of the reader as indicated below.
LED INDICATOR
LED color
| ****
meaning
---|---
LED off
| ****
The USB device has not been initialized yet or the device is in sleep mode.
Orange
| ****
Initializing
Green
| ****
Card reader initialized. Ready to read a card.
White
| ****
Card read OK
Red
| ****
Card read error or card refused
Blue
| ****
Programming card processing
Yellow
| ****
Firmware update
MOUNTING INSTRUCTIONS
Please mount the card reader to an MFD using the mounting kit.
Keep unprotected cords out of the path of foot traffic to prevent tripping. Do not leave cords dangling anywhere where they can be pulled down and tripped over.
CONFIGURATION
For configuration, see USB Reader tool for Reader configuration.
Risk Description
|
Control Measures (details of all existing controls)
|
Risk Analysis
|
Additional Measures
(details of all additional checks to be carried out)
---|---|---|---
O
|
P
|
Risk Rating
Falling of object/ component
|
A mounting kit is supplied with the device.
|
Small
|
Possible
|
L (C4)
|
Correct mounting is indicated in the manual.
Tripping over a cable
|
The cable is fitted with a connector at both ends that can be disconnected.
|
Serious
|
Possible
|
M (C3)
|
A recommendation on cable placement is indicated in the manual.
Entry of water into electronic components
|
The device is damaged.
|
Small
|
Possible
|
L (C4)
|
The manual states the user is to prevent water from entering the device.
Risk Description
|
Control Measures (details of all existing controls)
|
Risk Analysis
|
Additional Measures
(details of all additional checks to be carried out)
---|---|---|---
O
|
P
|
Risk Rating
Exposure to non- ionizing radiation (radiofrequency)
|
The device produces radiofrequency radiation below limits indicated by relevant norms.
|
Small
|
Improb.
|
L (D4)
|
The norms the device meets are listed in the manual:
EN 55032:15
EN 55024:10
ETSI EN 301489-3 V1.6.1:13 ETSI EN 301489-1 V1.9.2:11 ETSI EN 301489-1 V2.2.0:17 ETSI EN 301489-3 V2.1.1:17 ETSI EN 300330-2 V1.6.1:15 ETSI EN 300330-1 V1.8.1:15 ETSI EN 300330 V2.1.1:17 EN
60950-1:2006+A11:2009+A1:20
10+A12:2011+A2:2013
EN 62368-1:2014/AC:2015
Y SOFT CORPORATION, a.s.
Technology Park, Technická 2948/13
616 00 Brno
Czech Republic
Phone:+420 533 031 500
info@ysoft.com
FCC statements
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications or changes to this equipment. Such
modifications or changes could void the user s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a ClassB digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment of and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
IC statements
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
Radiation Exposure Statement
The product comply with the Canada portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in
this manual. The further RF exposure reduction can be achieved if the product
can be kept as far as possible from the user body or set the device to lower
output power if such function is available.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>