thermaltake TPD-1650AH3FSG Toughpower GF3 1650W Graphics Card Instruction Manual
- June 3, 2024
- thermaltake
Table of Contents
TPD-1650AH3FSG Toughpower GF3 1650W Graphics Card
Instruction Manual
Warnings and Caution
- Do not unplug the AC power cord when the power supply is in use. Doing so may cause damage to your components.
- Do not place the power supply in high humidity and /or temperature environment.
- High voltages exist in the power supply. Do not open the power supply case unless you are an authorized service technician or electrician. Doing so will void the warranty.
- The power supply should be powered by the source indicated on the rating label.
- Make sure all cables are plugged in properly. Loos and improper connections would damage the power supply and your system.
- Please use only genuine Thermal take modular cables with Thermal take power supply models. Third-party cables might not be compatible and could cause serious damage to your system and power supply. The warranty is voided with the use of third-party cables.
- All warranties and guarantees will be voided, if failure to comply with any of the warnings and cautions covered in this label.
Components Check
- TOUGH POWER GF3 power supply unit
- AC power cord
- User manual
- Mounting screws x 4
- Cable straps x 4
Power Connector Introduction
CABEL| | | | | | |
---|---|---|---|---|---|---|---
Wattage| Main Power Connector| Connector(8Pin/4=4Pin)| SATA Connector 5 Pin|
PCle Connector (6+2Pin)| PCle Connector
(12+4Pin)| Peripheral
Connector
(4Pin)| .
Floppy Adapter
(4 Pin)
1650W| 2| 16| 9| 2| 8| 1| 1
1350W| 2| 12| 6| 1| 4| 1| 1
Output Specification
Continuous Power| AC INPUT| Input Voltage: 100 – 240V- ; Input
Current: 20 – 16A ; Frequency: 50 – 60Hz
---|---|---
1650W| DC OUTPUT| +3.3V| +5V| +12V| -12V| +5VSB
Max Output Current| 25A| 25A| 137.5A| 0.3A| 3.0A
Max Output Power| 130W| 1650| 3.6W| 15W
Continuous Power| AC INPUT| Input Voltage: 100 -240V-, Input
Current. 16- 8A, Frequency 50- 60Hz
1350W| DC OUTPUT| +3.3V| +5V| +12V| – 12V| +5VSB
Max Output Current| 24A| 24A| 112.5A| 0.5A| 3.0A
Max Output Power| 120W| 1350W| 6.0W| 15 .0W
Installation Steps
Note: Make sure that your system is turned off and unplugged. Disconnect
the AC power cord from your old power supply.
Step 1
Removing Your existing power supply
- Make sure that your system is turned off and unplugged.
- Disconnect the AC power cord from your wall outlet or UPS and the existing power supply.
- Disconnect all the power cables from your graphic card, motherboard, and all other peripherals.
- Follow the directions in your chassis manual and uninstall your existing PSU.
Step 2
-
Make sure the power supply’s AC power cable is not connected.
-
Follow the directions in your chassis manual and install the power supply with the screws provided.
-
Connect the 24-pin or 20-pin main power cable to the motherboard.
-
Connect the eight-pin +12V (EPS12V) cable to the motherboard.
4.1 If your motherboard has an eight-pin +12V socket, connect the eight-pin cable directly to your motherboard.
4.2 If your motherboard has a four-pin socket, detach the four-pin from the eight-pin cable, and then plug this four-pin cable directly to your motherboard. -
Connect the peripheral cables, PCI-Express cables, and SATA cables.
5.1 Connect the SATA power connector to devices with a Serial ATA interface.
5.2 Connect the 6+2pin or 12+4pin PCI-E power connector to the PCI-E graphic cards if required.
5.3 Connect the 4-pin peripheral power connector to peripherals devices if needed. -
Connect the AC power cord to the power supply and turn it on by pushing the switch to the ON position (marked with “I”).
Attention!
When the Smart Zero Fan mode is turned on, the fan will not spin until the
load exceeds 30% of the power supply, minimizing the fan noise; It is normal
if the fan does not operate when the computer is at a low working load.
Total Protection
| Wattage | 1650 | 1350W |
|---|---|---|
| Voltage Source | Voltage Source | |
| Protections | +3.3V | +5V |
4.3V
Over Voltage Protection| 2.0-2.4V| 7.0V ail| 15.6V| 1p 4.3V| 7.0V| 15.6V
Under Voltage Protection| 20-24V| 3.3-3.7V| 10.3-11.0V| 2.0-2.4V| 3.3-3.7V|
10.3-11.0V
Over Current Protection| 27.5-37.5V| 27.5-37.5V| 178.7511 28.8-36V 233.75V|
28.8-36V| 146.25—191.25V
Short Circuit Protection I| Activated| when any DC rails short circuited.
Over Power Protection| The power supply shall be shut down the power supply is
130% – 170%| and latch off, if the wattage of over continuous power.
Over Temperature Protection| Protection temperature is 55°C to 75°C at 115V
and full load.| Protection temperature is 55°C to 65°C at 115V and full load.
EMI& SAFETY
EMI Regulatory & SAFETY Standards
TOUGHPOWER GF3 1650W/1350W| CE, UKCA, cTUVus TUV, FCC, EAC, S-Mark and BSMI
certified
CAN ICES-003(8) /NMB-003(8)
Environments
| Operating temperature | 0 Cto +50·C |
|---|---|
| Operating humidity | 20% to 90% non-condensing |
| MTBF | > 100,000 hours |
Trouble-Shooting
If the power supply fails to function properly, please follow the troubleshooting guide before application for service
- ls the power cord plugged properly into electrical outlet and into the power supply AC inlet?
- Please make sure the I/O switch on the power supply is switched to I position
- Please make sure all power connectors are properly connected to all the devices
- Ifconnected to a UPS unit, is the UPS on and plugged in?
If the power supply is still unable to function properly after following the above instruction, please contact your local store or Tt branch office for after sales service. You may also refer to Thermaltake’s website for more technical support thermaltake.com
Documents / Resources
|
thermaltake TPD-1650AH3FSG Toughpower GF3 1650W Graphics
Card
[pdf] Instruction Manual
TPD-1650AH3FSG, Toughpower GF3 1650W Graphics Card, TPD-1650AH3FSG Toughpower
GF3 1650W Graphics Card
---|---