Kahomvis SHU-QPW2-107 2.5 HP Black Stainless Steel Foldable Electric Treadmill User Manual

****

Kahomvis SHU-QPW2-107 2.5 HP Black Stainless Steel Foldable Electric

Treadmill

TIPS:
Thank you so much for purchasing our product.
Please read this manual carefully before use it; keep the manual at proper place.
CAUTION
To avoid any hurts, please read this manual carefully before using.

• For safety purpose, do not stand on running belt while start.
• Please stop immediately if you experience any kind of pain, including but not limited to chest pains, nausea, dizziness, or cramp.
• Please speed up slowly if needed.
• Adjustment of belt is prohibited during using.
• It is suggested to wear sports shoes while using this equipment.
• Children, the elder, the pregnant, and patients are prohibited from using this machine.
• Please clip the safety key on your clothing during using.
• Please firmly hold the handle bars during using.

SAFETY AND NOTIICE

• Please put the machine on flat ground. It is unsuitable to put the machine at following places:

1. Outdoors.(The machine is specially designed for indoor use only)
2. Slant ground or slant places on balcony.
3. Sunlight area or near heater.
4. Noisy places.

• The proper power for the machine is A.C 110V.
• Error may appear on display if the power is not stable. Please do not use the same socket together with computer, air conditioner etc.
• It is suggested to wear sports shoes and gym suit while use the machine.
• Please speed up or speed down slowly.
• Make sure no child or other object is near while folding or unfolding the machine.
• The treadmill should not be located near water or wet object. Error or damage may be caused if water or other liquids drop into the equipment.

CAUTION DURING USE

• If you do not feel well before using, please consult your doctor or coach.
• Merax is not responsible for any injury or damage caused by improper use.
• Please unplug the equipment when not in use.
• Please unplug the treadmill before cleaning, moving or change parts for the machine.
• Children, the elder and the pregnant are prohibited from using the machine. Patients should consult their doctor before starting any exercise routine.
• Please place the machine on a level flat surface. There should be 2M of clearance behind the treadmill.
• Do not start the machine when it is folded.
• Keep all electrical components, especially motor, power cord and plug, away from water or other liquids.
• Do not wear clothes, such as long dress, that might catch on any part of the treadmill while using.
• Do not place the treadmill in area that will block any vent or air openings.
• Do not put any objects on the machine.
• Put away the plug from heated place or fire seat.
• Please switch off all functions and pull out plug after using.
• Do not stand on the belt while you’re preparing to use the treadmill.
• Do not disassemble the machine without consulting professional technicians.
• Please make sure the running belt is fastened before using.

TECHNICAL SPECIFICATION

PRODUCT SPARE PARTS

PRODUCTS MAIN PARTS

ASSEMBLY

1. Open the box and take out the machine and all parts. Pull up the upright tubes on both sides .
2. Use Part 1 + Part 3, Part 2 + Part 3 to assemble upright tubes to base frame , at this step, please do not fix all screws tightly.
3. Connect panel to upright tubes. Please use the preset knobs with nuts at the top of tubes to fix panel to both left and right upright tubes. Then connect wire at right side between right tube and panel. Then pull panel to horizon level, use Part 1 and Part 3 to fix panel.
4. Put fixed knob (part 5)and tension knob (part 4) to machine.
5. Put the red safety key to panel.

End Caps Assembly

CONSOLE INSTRUCTON

1. Connect machine to power, turn on the switch at the front base frame, then press “START” key, the machine will start from 0.5mph after 3 seconds. Please make sure the safety key is on the panel before using.
2. Press”+” key for speed up and “-” key for low down. The fastest speed is 7.5mph and lowest is 0.5 mph.
3. “SHORTCUT” Key：1, 3, 5, 7 to set the speed quickly.
4. Press “MODE” key， the screen will show Speed、 Time、 Calories. And the scan light will light from speed、 time、 calorie every 5 seconds.
5. Display monitor has 12 programs from P1-P12. While on standby, press “PROG” to set the programs then press “START” to start the machine.
6. While the machine is in use and running, during the auto programs, the (-) and (+) keys are not available. If you want to exit the auto programs, select “STOP” or remove the safety key, and turn on the machine again or place safety key back on. And then you can select desired speed.
7. For emergency stop, please pull out the safety key. The machine will stop very slowly. Pull out safety key and the screen will show “Err”, put it back and on it will show “OFF”.
8. Press “STOP” key, the machine will be stopped.

FOLDING UP AND SETTING DOWN

Fold ：
Turn off the fixed knob at the bottom and lift up the running board to upright position. Use the Tension knob on upright tube to secure the running board as shown in picture above and then you can move the machine around.
Unfold ：
Pull out the tension knob and let down the running board, secure it with the knob at the bottom.

USAGE OF SILICONE OIL

Pull up the running belt slightly, apply silicone oil to the backside of the belt and the top surface of the running deck. Start the machine and keep it running for 3 minutes so that the oil spread and even out. It is necessary to maintain your treadmill like this with 1/3 bottle silicone oil every 30 working hours of the machine for optimal performance, which also helps extend the service life of parts.

RUNNING BELT ADJUSTMENT

1. Running belt deviate to left
   Start the machine by speed at 1-2mph without loading, use Allen wrench to screw the bolt 1/4 turn clockwise . Keep the machine running without loading for 1-2 minutes to gauge. Repeat the previous step if more adjustment is needed, until the belt moves to the center.

2. Running belt deviate to right
   Start the machine by speed at 1-2mph without loading, use Allen wrench screw the bolt 1/4 turn clockwise . Keep the machine running without loading for 1-2 minutes to gauge. Repeat the previous step if more adjustment is needed, until the belt moves to the center.

3. Running belt slipping
   If the running surface becomes slipping, tighten bolts on both ends 1/2 turn clockwise

with Allen key. Repeat if necessary until the belt is properly adjusted.
Running belt logjam
If the running belt is in dead condition, loosen bolts Allen wrench to make the screw 1/2 circle both left and right till this logjam solved.

TROUBLE SHOOTING

1. Put safety key in the yellow area of panel
2. Err(or E00) still shows or there is no function, change the computer screen/display monitor.

E2| Control Board Error| Control board is broken or pseudo soldering on control board| Replace control board
E4| Control Board Error| Control board is broken| Replace control board
E5| Overcurrent Protection| Control board short circuit or motor blocked|

1.  Open the motor cover and check whether the motor is blocked. Remove the block if yes.
2. Replace the control board if it’s not blocked, or the error still shows.

E6| Motor Error| Motor broken or motor line fall off|

1.  Open the motor cover and check whether the motor is broken or whether the motor wire is connected to control board properly. Reconnect the wire is recommended.
2.  Replace the control board if the error still shows.

E7| **** Communication Failures| Wires from the control board to panel board are broken or not properly connected|

1. Make sure the wires from the control board and panel board are connected securely and not damaged.
2.  Replace the control board if the error still shows.

E8| Overload Protection| Excess of electricity or user exceeded max load weight|

1. Make sure the user does not exceed max weight capacity.
2. Reconnect power and re-start the machine.
3. Replace the control board if the error code still show.

FCC COMPI.IANCE STATEMENT

This device complies with part I5 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>