Hello Kitchen SL620D Smart Bidet Seat Toilet Suite Instruction Manual
- June 3, 2024
- Hello Kitchen
Table of Contents
Hello Kitchen SL620D Smart Bidet Seat Toilet Suite
Installation
- Cautions for safety. Please observe the following rules.
- The following symbols are used to indicate important safety instructions for the use of the product.
Danger
- Indicates an imminently hazardous situation which,if not avoided,will result in death or serious injury.
warning
- Indicates dangerous situations where the user could suffer death or serious injury if this product is used incorrectly.
Do not dismantle
- Indicates not to dismantle this product.
Observe strictly
- Indicates observing the following precaution before using this product.
Accessories
- Tip. When you have multiple smart toilets, set them to different channels for remote control.
Setting channel steps:
- Please plug in the toilet.
- Press the STOP button on the toilet panel, and hold down the button.
- Meanwhile, press the MALE CLEANING button to change the channel.
- There are 8 channels for you to choose from, and you can hear a different beep on different channels. choose one of them.
- Take out the remote control, hold down the two buttons”+” and”-“until hearing the beep, and release the buttons immediately.Channel setting is complete.
Note: Press the”CHOOSE”button for 3 seconds to open or close the motion sensor
-
Install the Battery box
Put the battery in the battery box, then connect the Battery box to the toilets. -
P-trap installation
Adjust the position of the toilet drain oullet,and then connect the toilet to the wall. -
Install shutoff valve
-
Close the main water supply
-
Wind Teflon tape around water shutoff valve
-
Connect the shutoff Valve, tighten up with wrench.
-
Connect the constant perssure valve.
Note: After Installing the shutoff Valve, please turn on the water supply and Valve to flush the dirt for 30s and check whether there is a leakage.
Connect the hose
Fix the hose to the Constant pressure valve
Apply glass glue.
- Flush the toilets and find whether there is a leakage with a paper.
- Water may get into the part between the lower end of the toilet and the floor and leave stain.Apply glass glue(Not Concrete)to prevent water penetration.
Connect Power
- insert the power plug into the outlet
- Tum on the shutoff valve.
- Press the flush button on the remote control to do a test.
- Diameter of Water outlet 112’G Inlet Water Hose Length 60cm
- Length of Power Cord 100cm
- Water Pressure Minimum 150kPa.Maximun 750kPa,nominal fixed flush volume was 5L
- Electrical Standard 10amp power point required
- Installation To be carried out by a licensed plumber. Installation as per local region, council plumbing specifications, and plumbing codes additional backflow devices may be a requirement
- The position of the power outlet and water outlet can also be flexible according to the real situation.
Cautions for safety. Please observe the following rules.
Accessories
- The following symbols are used to indicate important safety instructions for the use of the product.
- Danger: Indicates an imminently hazardous situation that,if not avoided, will result in death or serious injury.
- Warning: Indicates dangerous situations where the user could suffer death or serious injury if this product is used incorrectly.
- Do not: Indicates not to dismantle this product dismantle
- Observe strictly: Indicates to observe the following precaution before using this product
Tip. When you have multiple smart toilets, set them to different channels for remote control
Setting channel steps:
- Please plug in the toilet
- Press the STOP button on the toilet panel,hold down the button.
- Meanwhile, press the MALE CLEANING button to change the channel
- There are 8 channels for you to choose from, and you can hear different beep on different channels.Choose one of them.
- Take out the remote control, hold down the two buttons”+*”until hearing the beep, and release the buttons immediately.Channel setting is complete.
Note: Press the”CHOoSE” button for 3 seconds to open or close the motion sensor
- Install the Battery Box
Put the battery in the battery box, then connect the Battery box to the toilets.
Install the Flange on the floor
- Fix the flange on the bottom
- Connect the toilet with flange to the drain pipe on the floor
- Slightly press the toilets after the toilet is connected to make the connection better.
Note: The expansion pipe-type toilets do not need a flange, just connect the Drain pipe directly.
Install shutoff valve
- Close the main water supply
- Wind Teflon tape around water shutoff valve
- Connect the shutoff Valve, tighten up with wrench.
- Connect the constant perssure valve.
Note: After installing the shutoff Valve, please turn on the water supply and Valve to flush the dirt for the 30s and check whether there is a leakage.
Connect the hose
Fix the hose to the Constant pressure valve
Apply glass glue.
- Flush the toilets and find whether there is a leakage with a paper.
- Water may get into the part between the lower end of the toilet and the floor and leave stain.Apply glass glue (Not Concrete) to prevent water penetration.
Connect Power
- Insert the power plug into the outlet
- Turn on the shutoff valve.
- Press the flush button on the remote control to do a test.
-
Tel:03 9998 0999
Documents / Resources
|
Hello Kitchen SL620D Smart Bidet Seat Toilet
Suite
[pdf] Instruction Manual
SL620D Smart Bidet Seat Toilet Suite, SL620D, Smart Bidet Seat Toilet Suite,
Bidet Seat Toilet Suite, Seat Toilet Suite, Toilet Suite, Suite
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>