Beijing Microlight Internet Technology Q340 Embedded QR Code/Card Reader User Manual

Beijing Microlight Internet Technology Q340 Embedded QR Code/Card Reader

Disclaimer

Before using the product, please read all the contents in this Product Manual carefully to ensure the safe and effective use of the product. Do not disassemble the product or tear up the seal on the device by yourself, or Beijing Vguang Internet Technology Co., Ltd. will not be responsible for the warranty or replacement of the product.
The pictures in this manual are for reference only. If any individual pictures do not match the actual product, the actual product shall prevail. For the upgrade and update of this product, Beijing Vguang Internet Technology Co., Ltd. reserves the right to modify the document at any time without notice.
Using the product is at the user’s own risk. To the maximum extent permitted by applicable law, damages and risks arising from the use or inability to use this product, including but not limited to direct or indirect personal damage, loss of commercial profits, Beijing vguang Internet Technology Co., Ltd. will not bear any responsibility for trade interruption, loss of business information or any other economic loss.
All rights of interpretation and modification of this manual belong to Beijing Vguang Internet Technology Co., Ltd.

Edit History

Change date

| Version| Description|

Responsible

---|---|---|---

2021.5.15

| V1.0|

Initial version

|

Preface

Reading this document carefully can help you understand the functions and features of this device, and quickly master the use and installation of the device.

Product Introduction

The Q340 QR code reader was a specially designed embedded type device, which has various output interface, including USB, RS232, RS485, TTL, Wiegand, suitable for vending machines, turnstiles.

Product Feature

1. Scan code& swipe card all in one.
2. Fast recognition speed, high accuracy, 0.1 second the fastest.
3. Easy to operate, humanized configuration tool, more convenient to config the reader.
4. Protection level IP67.

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Product Appearance

OVERALL INTRODUCTION

PRODUCT SIZE

Parameters

General Parameter

General Parameter

Output interface| USB, RS232, RS485, TTL, wiegand
Indicating method| Red, green light indicator
Beeper
Imaging sensor| 300,000 pixel CMOS sensor
Max resolution| 640480
Mounting method| embedded mounting
Size| 75mm65mm28.35mm
Reading window size| 56mm51mm
Certification| EC, FCC

Reading Parameter

QR Code Recognition Parameter

Symbologies| QR, PDF417 ,CODE39 ,CODE93 ,CODE128, ISBN10, ITF, EAN13, DATABAR, aztec, etc.
Supported decoding| Both Mobile QR code and printed QR code
DOF| 0mm~62.4mm(QRCODE 15mil)
Reading accuracy| ≥8mil
Reading speed| 100ms per time(average), support reading continuously
Reading direction| tilt±56.3°
rotation±360°
deflection±55.7° (15milQR)
FOV| Horizontal Field 72.1°
Vertical field 56.6°
Filed angle 84.3° (15milQR)

RFID Reading Parameter

Supported cards| ISO 14443A, ISO 14443B protocol cards
Reading method| Read UID
Working frequency| 13.56MHz
Distance| ＜5cm

Electric Parameter

The power input can be provided only when the device is connected properly. If the device is plugged or unplugged while the cable is live (hot plugging), its electronic components will be damaged. Make sure that the power is turned off when plugging and unplugging the cable. Poor power supply, too short interval power off and on operation may cause the device cannot work in a stable and normal status. It is necessary to keep the power input stable. After turning off the power input, it need to takes more than 2 seconds to turn on the power input again.

Electric Parameter

Working voltage| DC 5V-24V
Working current| 200mA (5V typical value)
Power consumption| 1000mW (5V typical value)

Working Environment

Work Environment Parameter

ESD protection| ±8kV (Air discharge), ±4kV (contact discharge)
Working temp| -20°C-65°C
Storge temp| -40°C-80°C
RH| 5%-95% (No condensation) (environment temperature)
Ambient light| 0-100000Lux (Non direct sunlight)

Device Configuration

Use the Vguang config tool to configure the device.

Config the device as the step shows, the example are showing 485 version reader.

Step 1, select the model number Q300
Step 2, select the output interface, and config the corresponding serial parameters.
Step 3, config as your needs.
Step 4, after config as your needs, click “config code”
Step 5, use the scanner to scan the configurations QR code generated by the tool, then restart the reader to finish the new configurations.
For more details about configurations, please refer to the “Vguang configuration tool user manual”.

Mounting Method

The product using CMOS image sensor, the recognition window should avoid direct sun or other strong light source when install the scanner. The strong light source will cause the contrast in the image too big to decoding, the long term exposure will damage the sensor and cause the device failure.
The recognition window are using tempered glass, which has good transmission of the light, and also a good pressure resistance, but still need to avoid scratching the glass by some hard object, it will affect the QR code recognition performance.
The RFID antenna was in the underside of the recognition window, there should have no metal or magnetic material within 10cm when installing the scanner, or it will affect the card reading performance.

Step 1: open a hole in the mounting plate.

Step 2: assemble the reader with the holder, and tighten the screws.
Screw specification: M2*5 self-tapping screw.

Step 3: Assemble the holder with the mounting plate, then tighten the screws.

Step 4: Installation finished.

Attention

1. The equipment standard is 5-24V power supply, it can get power from the access control power or power it separately. Excessive voltage may cause the device fail to work normally or even damage the device.
2. Do not disassemble the scanner without permission, otherwise the device may be damaged.
3. The installation position of the scanner should avoid direct sunlight. Otherwise, the scanning effect may be affected. The panel of the scanner must be clean, otherwise it may affect the normal image capture of the scanner. The metal around the scanner may interfere with the RFID magnetic field and affect card reading.
4. The wiring connection of the scanner must be firm. In addition, ensure the insulation between the lines to prevent the equipment from being damaged by a short circuit.

Contact Info

Company Name: Beijing Vguang Internet Technology Co., Ltd,
Address: China Meteorological Science and Technology Park, No.2, Zhenxing Road, Changping District, Beijing, China
Hot line: 400-810-2019/ +86 18914995180

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>