LDT 700012 Permanent PowerSwitch Unit Instruction Manual
- June 3, 2024
- LDT
Table of Contents
LDT 700012 Permanent PowerSwitch Unit
Introduction/Safety instruction:
You have purchased the Permanent-Power-Switch-Unit DSU for your model railway.
The Permanent-Power-Switch-Unit DSU is a high quality product that is supplied
within the Digital-Professional-Series of Littfinski DatenTechnik (LDT).
We wish you having a good time using this product.The Permanent-Power-Switch-
Unit DSU comes with a 24 month warranty.
- Please read the following instructions carefully. Warranty will expire due to damages caused by disregarding the operating instructions. LDT will also not be liable for any consequential damages caused by improper use or installation.
- We designed our devices for indoor use only.
Function
Information for switching the digital systems are active as long as the
respective key of the keyboard will be pressed. On this way is it possible to
operate turnouts, signals or uncoupling devices by repeated pressing the key.
If a standard mono-stable relay has been connected to the decoder output this
relay will be activated for the duration of pressing the key only. Such a
relay can not be used for street-, building- or turnout illumination.
For such applications is it suitable to use the Permanent-Power- Switch-Unit
DSU because this unit includes a bistable relay. A short impulse will switch-
over this relay into the secondary switch position and remains there even
without voltage at the switch contacts.
If the permanent power switch DSU will be combined with the TurnTable-Decoder
TT-DEC the polarity of a 2-conductor turntable bridge will be automatically
changed on every 180 degree turning.
Connecting the Permanent-Power-Switch DSU to the Turnout-Decoder:
Attention: Before starting the installation switch off the voltage of the layout (switch-off the transformers or disconnect the mains supply).
Connect the Permanent-Power-Switch Unit DSU to an output of a Turnout-Decoder S-DEC-4 or to the Turntable-Decoder TT-DEC as per advice on the backside of this instruction.
The clamp KL1 on the left side of the DSU marked “G”, “COM” and “R” shall be used for this connection. The output clamps of the Turnout-Decoder S-DEC-4 are as well identified by the letters “G” and “R”. The connection at the DSU marked with ”COM” shall be connected to the middle connection of the decoder output. The clamps of the Turntable-Decoder TT-DEC are corresponding marked with “G”, “Com” and “R”. The bistable relay of the Permanent-Power-Switch-Unit DSU contains two switches over contacts at the clamps KL2 and KL3 (upper and lower position). Each switch contact can cover a maximum load of 1 Ampere. The common contact of the switch (block pole) is always the middle contact of the DSU output clamps. With respect to the required power load of the consumers the output can be connected to one or to both clamps.
Further products within the Digital Professional Series:
-
M-DEC
4-fold decoder for motor driven turnouts (Conrad, Hoffmann, Fulgurex etc.) With free programmable decoder addresses and possible external power supply. -
SA-DEC-4
4-fold switch decoder with 4 bistable relays of 2 Ampere switching load each. With free programmable decoder addresses. -
RM-88-N / RM-88-N-O
16-fold feedback module (also with integrated opto coupling) for the s88-feedback bus for the connection to Memory und Interface (Märklin-Digital), Intellibox, TWIN-CENTER, Märklin Central Station 1 and 2, EasyControl, ECoS, High Speed Interface HSI-88(-USB) and DiCoStation. -
RM-GB-8-N
8-fold feedback module with integrated track occupancy detectors for the s88-feedback bus. All components are available as kits (-B), as finished modules (-F) or as finished modules in a case (-G).
Picture 1: Permanent-Power-Switch-Unit DSU at output 2 of the Turnout- Decoder S-DEC-4 for the switching the turnout illumination.
Picture 2: Permanent-Power-Switch-Unit DSU in interaction with the Turntable-Decoder TT-DEC for the polarity switching of the turntable bridge.
Made in Europe by
Littfinski DatenTechnik (LDT)
Bühler electronic GmbH
Ulmenstraße 43
15370 Fredersdorf / Germany
Phone: +49 (0) 33439 / 867-0
Internet: www.ldt-infocenter.com
Subject to technical changes and errors. Ó 09/2022 by LDT
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>