ldt-infocenter 000123 12 Pin IBP Connection Cable Instruction Manual
- October 27, 2023
- ldt-infocenter
Table of Contents
Connection Cable (1m)
for the 5-poles Boosterbus
from the Digital-Professional-Series !
Kabel Booster 1m Part No.: 000123
Instruction Manual
Pin IBP Connection Cable
Twisted and interference protected for the connection of Digital Command Stations (e.g. Märklin Control Unit, Central Station 1 and 2, DiCoStation and KeyCom as well as Intellibox, TWIN-CENTER, EasyControl, ECoS 1 and 2, Commander) with Boosters (e.g. 6015 / 6017, Power 3, TWIN-BOOSTER, DB-2 and DB-4) and for the connection of Boosters to each other.
This product is not a toy! Not suitable for children under 14 years of age!
The kit contains small parts, which should be kept away from children under 3
years of age!
Improper use will imply danger of injuring due to sharp edges and tips! Please
store this instruction carefully.
Introduction / Safety Information:
You have purchased the connection cable Kabel Booster 1m for the 5-poles
Boosterbus for your digital model railway.
The connection cable is a high quality product which is supplied within the
assortment of Littfinski DatenTechnik (LDT).
We are wishing you having a good time using this product.
The connection cable comes with 24 month warranty.
- Please read the following instructions carefully. Warranty will expire due to damages caused by disregarding the operating instructions. LDT will also not be liable for any consequential damage caused by improper use or installation.
- We designed our devices for indoor use only.
- Attention : Please switch off your model railway by disconnecting the transformers from AC-current before starting any installation.
Connecting the Kabel Booster 1m:
The connection cable Kabel Booster 1m consists of a 1 meter twisted bus cable with two original connectors such as used on several digital components supporting the 5-poles boosterbus (e.g. Digital Command Stations Märklin Control Unit, Central Station 1 and 2, DiCoStation and KeyCom as well as Intellibox, TWIN-CENTER, EasyControl, ECoS 1 and 2, Commander and Booster 6015 / 6017, Power 3, TWINBOOSTER, DB-2 and DB-4).
The first Booster has to be always directly connected with the 5-poles
booster-bus cable Kabel Booster 1m to the Digital Command Station.
The second Booster shall be connected to the first etc.
If you want to create a connection to the DigitalBooster DB-2 or DB-4 you have
to plug one connector of the Kabel Booster 1m to the digital command station
or to the previous booster.
The position of the inserted plug at the Control Unit, Intellibox, TWIN-
CENTER, EasyControl, Commander, Märklin Booster 6017, Power 2 and Power 3 is
correct if the cable shows to the bottom. At the Märklin Booster 6015 the
Kabel Booster 1m has to show to the top.
The booster-bus socket of the Central Station 2 is located at the underside of
the Digital Command Station.
The Digital Command Stations Central Station 1 and ECoS 1 and 2 contain a
plug-in connection clamp for the 5-poles booster-bus connection.
For those and other digital command stations you can find colored samples at
the Internet on our Web-Site
(www.ldtinfocenter.com) within the section
“Sample connections” to show you the correct connection of the Kabel Booster
1m.
At the DigitalBooster DB-2 and DB-4 connect the second plug of the Kabel
Booster 1m onto the pinbar ST1 which is marked with “IN”.
Please take care that the white single wire of the Kabel Booster 1m
corresponds to the white marking at the pinbar ST1.
The plug of the 5-poles booster bus cable has been correct attached onto the
DigitalBooster DB-2 or DB-4 if the twisted cable shows away from the booster.
If a following Booster shall be connected to a DigitalBooster DB2 or DB-4 by
use of the 5-polige Boosterbus-Cable this has to be done via the pin-bar ST2
(“OUT”).
Using the Kabel Booster 1m on Märklin Control Unit and Booster 6017 /
6015:
The opposite sketch shows the correct connection of the Kabel Booster 1m on the Märklin Control Unit and Märklin Booster 6017.
The opposite sketch shows the correct connection of the Kabel Booster 1m on
the Märklin Control Unit and Märklin Booster 6015.
Further products from the Digital-Professional-Series:
S-DEC-4
4-fold turnout decoder for four magnet accessories with free programmable
decoder addresses and possible external power supply.
SA-DEC-4
4-fold switch-decoder with four bistable relays and free programmable decoder
addresses and possible external power supply.
LS-DEC-DB, -DR, -KS, -ÖBB, -SBB, -NS, -NMBS, -BR, -FS, -SNCF, -SJ, -CFL,
-USA, -CSD, -8×2
4-fold light signal decoder. Light signals switched directly via decoder
addresses.
RM-88-N / RM-88-N-O
16-fold feedback modules for the s88-feedback bus. RM-88-N-O with integrated
opto coupling.
RM-GB-8-N
8-fold feedback modules with integrated track occupancy detectors for the
s88-feedback bus.
HSI-88-(USB)
High Speed Interface for the s88-feedback bus. Offers the possibility to
create three feedback lines. The feedback reports will be transmitted directly
via the command station via the COM- (HSI-88) or the USB-Interface
(HSI-88-USB) to the PC.
Made in Europe by
Littfinski DatenTechnik (LDT)
Bühler electronic GmbH
Ulmenstraße 43
15370 Fredersdorf / Germany
Phone: +49 (0) 33439 / 867-0
Internet:www.ldt-infocenter.com
Subject to technical changes and errors. © 09/2022 by LDT
Märklin is a registered trademark
Documents / Resources
| ldt-
infocenter 000123 12 Pin IBP Connection
Cable
[pdf] Instruction Manual
000123, 12 Pin IBP Connection Cable, Connection Cable, 12 Pin IBP Cable, Cable
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>