thermaltake GF3 ARGB 750w 850W Toughpower Tt Premium Edition User Manual

Thermaltake GF3 ARGB 750w 850W Tough power Tt Premium Edition

Warnings and Caution

1.  Do not unplug the AC power cord when the power supply 1s in use.
2. Doing so may cause damage to your components. 2. Do not place the power supply in high humidity and /or temperature environment.
3. High voltages exist in the power supply. Do not open the power supply case unless you are an authorized service technician or electrician. Doing so will void the warranty.
4.  The power supply should be powered by the source indicated on the rating label.
5.  Make sure all cables are plugged in properly. Loos and improper connections would damage the power supply and your system.
6. Please use only genuine Thermaltake modular cables with Thermaltake power supply models. Third-party cables might not be compatible and could cause serious damage to your system and power supply. The warranty is voided with the use of third-party cables.
7. All warranties and guarantees will be voided if failure to comply with any of the warnings and cautions covered in this label.

Components Check

• AC power TOUGH POWER cord GF3 ARGB power supply unit
•  User Mounting manual screws x4
• Cable straps x 4 Power Connector Introduction

Output Specification

Installation Steps

Note: Make sure that your system is turned off and unplugged. Disconnect the AC power cord from your old power supply.

Step 1

1. Remake Disconnect sure that the excise your ting power system power cord Is supplied from turned off ur and the wall outlet is unplugged.
2. Disconnect ell Iha power cables from your graphic card, PS, and motherboard, and the expand sting ell power other supply. peripherals.
3.  Follow the directions In your chassis manual and uninstall your existing PSU.

Step 2

1.  Make sure the power supply’s AC power cable is not connected.
2.  Follow the directions in your chassis manual and install the power supply with the screws provided.
3.  Connect the 24-pin or 20-pin main power cable to the motherboard.
4.  Connect the eight-pin +12V (EPS12V) cable to the motherboard. If your motherboard has an eight-pin +12V socket, connect the eight-pin cable directly to your motherboard If your motherboard has a four-pin socket, detach the four-pin from the eight-pin cable and then plug this four-pin cable directly into your motherboard.
5.  Connect the peripheral cables, PCI-Express cables, and SATA cables. Connect the SATA power connector to devices with a Serial ATA interface. Connect the 6+2pin or 12+4pin PCl-E power connector to the PCl-E graphic cards if required. Connect the 4-pin peripheral power connector to peripherals devices if needed.
6. Connect the AC power cord to the power supply and turn it on by pushing the switch to the ON position (marked with “I”).

Attention
As this power supply is equipped with Smart Zero Fan, the fan will start running when a certain temperature is reached. It is normal if the fan does not operate when the computer is at a low working load.

RGB Lighting

1. Button-controlled 8 lighting modes
2. The lighting modes/colors can be changed when the Mode/Color button is pressed. You can either choose WNave, Spiral, Flow, Heartbeat, Ripple,
3. Full Lighted, or Spectrum Mode, or you can switch off the LEDs. Long pressing the Mode button can reset settings to default. The fan also has a built-in memory which can automatically recover the previous lighting mode after you restart the PSU.
4.  Synced with all RGB lighting devices on your system The lighting effects can be synced through the motherboards with the ARGB Sync function. After switching off the PSU, connected the ARGB Sync Cable to the ARGB Sync Header on the PSU and to the +5V ARGB header on the motherboard (Caution: This power supply does not support +12V
5. RGB header). Next, install the software provided by your motherboard’s vendor, such as ASUS AURA SYNC, GIGABYTE RGB FUSION, MSI MYSTIC LIGHT SYNC or AsRock Polychrome software. Finally, choose your favorite lighting theme. Every time you turn on the PC, the chosen
   lighting theme will be automatically recovered only when the software boots up.

Caution: Please power off the Pc and check the positive and negative ends on the connector before connecting the ARGB Sync Cable to the motherboard. Connecting the cable to the wrong header or in the wrong direction can damage the LEDs.

Total Protection

EMI & SAFETY
EMI Regulatory & SAFETY Standards CE, UKCA, cTUVus, TOV, FCC, CCC, EAC, S-Markand BSMI certified. CAN ICES-003(8) / NMB-003(8).

Environments

• Operating temperature o cto+,o ·c
• Operating humidity 20% to 90%,non-condensing
• MTBF > 100,000 hours

Trouble-Shooting

If the power supply fails to function properly, please follow the troubleshooting guide before applying for service:

1. Is the power cord plugged properly into the electrical outlet end to the power supply AC inlet?
2.  Please make sure the 1/0 switch on the power supply is switched to the I position.
3.  Please make sure all power connectors are properly connected to all the devices. 4 If connected to a UPS unit is the UPS on and plugged in?

If the power supply Is still unable to function properly after following the above instruction, please contact your local store or Tl bran oh office for after-sales service You may also refer to Thermaltake’s website for more technical support.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>