EnGenius EnStationAC Kit User Manual

June 7, 2024
EnGenius

EnGenius EnStationAC Kit - LOGO

Quick Installation Guide
EnStation5-AC Kit
EnStationAC Kit
ENH500 Kit
Version3.0
Outdoor Access Point/Client Bridge

Package Contents

EnGenius EnStationAC Kit - PACKAGE

EnGenius EnStationAC Kit - PACKAGE 2

Minimum Requirements
Broadband Internet Service
(Cable or DSL Modem)
Internet Browser
(Internet Explorer, Safari, Firefox, Chrome, Edge)

Connecting the Device

You must know :
This kit is pre-configured in AP (Master, 192.168.1.1) and CB (Remote, 192.168.1.2) mode. Wireless connection will be built automatically once the devices are powered up.
A) Remove the rear bottom panel.
B) Connect one end of the Ethernet cable into the LAN(PoE) port of the device and the other end to the PoE Port on the PoE Adapter.
C) Connect the Power cord to the PoE Adapter and plug the other end into an electrical outlet.
D) Connect the second Ethernet cable into the LAN port of the PoE Adapter and the other end to the Ethernet port into the computer.
E) Place the panel removed from step A back onto the device.
Note :
+ The device should ONLY be powered via Ethernet cable connected to included PoE Adapter. EnStation5-AC/ENH500: Support proprietary 24V PoE input. EnStationAC: Support proprietary 54V PoE input
+ For EnStationAC: The 2nd Ethernet port of the device can supply the 802.3af power source when used with the, included PoE Adapter.

EnGenius EnStationAC Kit - Connecting the Device

IP Address Configuration

A) Once your computer is on, ensure that your TCP/IP is set to On or Enabled. Open Network Connections and then click Local Area Connection. Select Internet Protocol Version 4 (TCP/IPv4).

EnGenius EnStationAC Kit - Address Configuration

B) If your computer is already on a network, ensure that you have set it to a Static IP Address on the interface. (Example: 192.168.1.10 and the Subnet Mask address as 255.255.255.0.)

EnGenius EnStationAC Kit - Address Configuration 2

Device Setup

A) To configure, the device, open a web browser and enter IP address as below.
EnGenius EnStationAC Kit - Device Setup– IP: 192.168.1.1 If the last two digits of the serial number on the device label is -1.
– IP: 192.168.1.2 If the last two digits of the serial number on the device label is -2.
B) A login screen will appear. By default, the username of the device is admin and the password is admin. Enter the current username and password of the device and then click Login.

EnGenius EnStationAC Kit - Device Setup 2

Note : The model name on login screen depends on the product you are using.
C) You can also use the EnWiFi App and connect to the management SSID which is on the device label and GUI to configure the device.  The default Wi-Fi password is 12345678.

Switching Modes

Configure on GUI
A) The device can operate in the following modes.
EnJet enabled: Access Point, Client Bridge, WDS AP, WDS Station.
EnJet disabled: Access Point, Client Bridge, WDS AP, WDS Bridge, WDS Station.

EnGenius EnStationAC Kit - Switching Modes

Note : The model name on the login screen depends on the product you are using.

B) Click on the Wireless link under the Network and set up the Operation Mode.

EnGenius EnStationAC Kit - Wireless

  • It may take up to 90 seconds for device to initially power up.
    Configure on EnWiFi App
    C) Use EnWiFi App, open configure → Wireless to setup the Operation Mode.

EnGenius EnStationAC Kit - App

Mounting the Device

Wall Mounting
EnStation5-AC / EnStationAC
A) Plug the dynamic stick into the bracket.
B) Screw the sealing nut and assembled parts, tighten it with 80kgf.cm.
C) Put the nock washer on the dynamic stick.
D) Assemble the mounting parts to the device.
EnGenius EnStationAC Kit - Mounting the DeviceE) Determine the mounting location. Mark and drill two pilot holes aligning to the screw holes of the bracket.
F) Put wall anchors into the holes and insert a screw into the wall anchor.
G) Screw and secure the bracket in place.
EnGenius EnStationAC Kit - Mounting the Device 2A) Determone where the Access Point to placed and stick the Adhesive label on the surface.
B) Use the appropriate drill bit drill to 8.1 mm diagram and 26 mm depth holes on the markings of the label.
C) Remove the label and Screw the anchors unto the holes until they are flush with the wall.
D) Screw the includes screws into the anchors. place the Access Point against the wall with the mounting screw heads.
EnGenius EnStationAC Kit - Mounting the Device 3

Pole Mounting

EnStation5-AC / EnStationAC
A) Plug the dynamic stick into the bracket.
B) Screw the sealing nut and assembled parts, tighten it with 80kgf.cm.
C) Put the nock washer on the dynamic stick.
D) Assemble the mounting parts to the device.

EnGenius EnStationAC Kit - Mounting the DeviceE) Thread the open end of the pole strap through the two tabs on the bracket.
F) Lock and tighten pole strap to secure bracket to the pole.
EnGenius EnStationAC Kit - Pole MountingA) Thread the open end of the Pole Strap through the two tabs on the Pole Mount Bracket.
B) Lock and tighten Pole Strap to secure Pole Mount Bracket to the pole.

EnGenius EnStationAC Kit - Pole Mounting 2

Technical Support

Country of Purchase| Service Center|

Service Information

---|---|---
North America www.engeniustech.com| Los Angeles, USA| support@engeniustech.com Local: (+1) 714 432 8668
www.engeniuscanada.com| Canada| rma@engeniuscanada.com Toll Free: 888 397 2788 Local: (+1) 905 940 8181
Europe
www.engeniusnetworks.eu| Netherlands| support@engeniusnetworks.eu
Local: (+31)40 8200 887
Africa / CIS / Middle East www.engenius-me.com| Dubai, UAE| support@engenius-me.com Local: (+971)4 339 1227
Asia / Oceania www.engeniustech.com.sg| Singapore| techsupport@engeniustech.com.sg Local: (+65) 6227 1088
Taiwan
www.nengeniustech.com.tw| Taiwan, R.O.C.| twsupport@engeniusnetworks.com Toll Free: 0800 (113 885 Local:(+886) 2 2652 1808

Notes —————–

EnGenius EnStationAC Kit - LOGO

Maximum data rates are based on IEEE 802.11 standards. Actual throughput and range may vary depending on many factors including environmental conditions, the distance between devices, radio interference in the operating environment, and mix of devices in the network.  Features and specif cations subject to change without notice. Trademarks and registered trademarks are the property of their respective owners. For the United States of America: Copyright © 2020 EnGenius Technologies, Inc. All rights reserved.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals