SAN HIMA SH-TMY61-9716-SLI Towing Mirrors User Manual

TOWING MIRRORS
USER MANUAL
SKU: SH-TMY61-9716-SLI
SH-TMY61-9716-BLK

ABOUT US

Founded in 2018, the San Hima brand stands for passion and enthusiasm for exploring the spectacular nature of the great outdoors. Since its inception, the trusted solutions and proven designs that San Hima offers to the market have made adventure and travelling flexible and enjoyable!
Based in Australia, San Hima has under its umbrella a wide selection of outdoor solutions, including cargo systems, vehicle protection accessories and tow & trailer parts, that are designed to help you carry your gear wherever your passion takes you and boost your performance when conquering the peaks!
At San Hima, we have wild souls and we are committed to designing products that are tough enough to take on any adventures and at the same time, making them safe and easy to use. These values in our conviction are what drive us to make innovations. Since pursuit your passion shouldn’t be complicated.
Live the Peak, Conquer the Everest, San Hima is your brand of choice!

SAFETY INSTRUCTIONS

• These mirrors are designed ONLY for NISSAN PATROL GU/Y61 1997-2016.
• DO NOT use the mirror for any purpose other than for which it is designed.
• Only have your mirrors extended when towing.
• Always check the condition of the mirror before every journey, if any part is damaged or missing,DO NOT use.
• Please use a glass cleaner to maintain the clarity of the mirror’s glass. When cleaning the surface,make sure to use a microfiber cloth to avoid scratches.

CONTENTS

1 x Left hand side mirror
1 x Right hand side mirror
6 x Nuts

TOOLS REQUIRED (NOT INCLUDED)
Flat screw driver
Phillips screw driver
Wrench

SPECIFICATION

Product Weight (Single): 3.82kg
Vehicle: NISSAN PATROL GU/Y61 1997-2016
Color: Black & Silver
Flat Mirror Adjusting Type: Electrical
Convex Mirror Adjusting Type: Manual
Extension Type: Manual
Folding Type: Manual
Housing Material: ABS
Base Material: Aluminum

INSTALLATION

Note: Installation procedures are for reference only, and may vary depending on your vehicle model.
The first procedure is to remove the internal door panel. Instructions below may refer to the “latch end” or the “hinge end”. This means that as you look at the driver’s door from the inside, the right side is the “latch end”, and the left side is the “hinge end”.

1. Lower door window all the way.

2. Remove door lever cover using small flat screw driver. Wedge the screw driver between the door lever cover and the lock button to gently loosen the cover. Repeat at the bottom if necessary.

3. Remove arm rest cover. You should be able to do this by hand. Grip the “latch end” of the cover and lift. Use a flat screw driver if it doesn’t come away easily.

4. Remove 2 screws behind the arm rest cover.

5. Remove the screw at the bottom of the handle section of the electrical control panel. Electrical control panel (handle section)

6. Lift out the electrical control panel from the “hinge end” first. This can be done by hand, although a flat screw driver may help unclip that end.

7. Remove electrical plug behind the electrical controls. There may be 2 electrical plugs on the driver’s side. The small plug can be removed by pressing the small tag. The other plug may need to be wedged out with a small flat screw driver.

8.  Remove screw located behind the electrical cover.

9. Remove triangular plastic cover at “hinge end” (covering the mirror bolts). You may need to wedge a flat screw driver between the cover and the door frame to unclip the small plug which keeps the cover in place.

10. The door panel connects to the door with several hidden plastic plugs that run along the base and up each sides. The plugs at the base of the door are located beside indents in the metal frame. Locate these indents and gently lever the panel away from the frame with a long flat screw driver. Continue pulling the panel up the sides of the door until all plugs have unclipped.

11. Once all the plugs have been detached, gently tap the base of the panel until the whole panel separates from the door frame. The next procedure is to remove the existing mirrors and to install the towing mirrors. It may be helpful to have another person assist in holding the mirrors whilst the existing mirrors are being detached and the towing mirrors are being installed.

12. Remove the electrical plug that connects the mirror to the mirror controls. You may need to peel back the clear plastic dust cover to access this plug. Remove the plug by pressing the tab and gently pulling the plug out.

13. Loosen the bolts, beginning with the bottom bolts. Hold the mirror or have someone hold it for you as the final top bolt is removed. Then carefully remove the mirror.

14. Thread through the towing mirror electrical cable. Then position the new mirror in place ensuring that the rubber seal is flush and in position.

15. Tighten all nuts.

16. Connect electrical plug ends. Then check that the electrical mirror buttons work. Place the clear plastic dust cover back.

17. Place the door panel back. Start with the window cavity at the top, pop it into place with strength.
    The plugs at the base and sides should line up and click into place.

18. Install screws: One behind the electrical control panel, two behind the arm rest.

19. Place the control panel electrical plug back. Then put the electrical control panel back in position.

20. Place the vertical screw back, which holds the electrical control panel in position.

21. Place the arm rest back, “hinge end” first.

22. Place the door handle cover back.

23. Place the triangular plastic cover back.

Repeat the above steps with the other towing mirror.Your new towing mirrors are now ready for use.

WARRANTY

WARRANTY PERIOD: San Hima warrants that each pair of our towing mirrors that is purchased while this Warranty is in effect will be free from defective workmanship and materials for a period of 3 years.
WHAT DOES THE WARRANTY COVER?
Under normal usage conditions, this warranty covers:

1. Any defect in design or manufacture which results in its failure to perform correctly as described.
2. Damage or loss incurred in transit.
3. We will either replace the product or provide you with a refund at our discretion provided that the fault is found to have been caused by a design or manufacturing defect and not misuse or tampering.
4. Shipping costs of returning the product for a proven defect.
5. The limited warranty is the only one that applies to this unit, and it sets forth all the responsibilities of San Hima.

THE WARRANTY DOES NOT COVER:

1. Travel and /or other expenses due to customer’s location.
2. Damage caused by adverse weather, extreme temperature, accidents, negligence, daily wear and tear, alteration, incorrect installation, improper use such as having your mirrors extended when not towing, or failure to check the condition of your mirrors before every journey.
3. This unit is not intended for commercial use.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>