Altronix T1M1LCK1 Mercury Access and Power Installation Guide

June 3, 2024
Altronix

Altronix T1M1LCK1 Mercury Access and Power

Altronix T1M1LCK1 Mercury Access and Power-fig1

Models Include

  • 4 Door Kits with Fused Outputs: T1M1LCK1
    Accommodates one (1) Intelligent Dual Reader Controller and one (1) Dual Reader Interface Modules.

  • 2 Door Kits with Fused Outputs: T1M1LCK2
    Accommodates one (1) Intelligent Controller and one (1) Dual Reader Interface Module.

  • 4 Door Kits with Fused Outputs: T1M1LCK3
    Accommodates up to two (2) Dual Reader Interface Modules.

  • Each fully assembled kit includes:

    • Trove1 enclosure with TM1 Altronix/Mercury backplane
    • One (1) AL400ULXB2 – Power Supply/Charger
    • One (1) ACM4 – Fused Access Power Controller
    • One (1) PDS8 – Dual Input Fused Power Distribution Module
    • One (1) VR6 – Voltage Regulator
    • One (1) Rocker Switch Bracket with One (1) Rocker Switch

Installation Guide
All registered trademarks are property of their respective owners.

  • nstalling Company: _____
  • Service Rep. Name: ____
  • Address: _____
  • Phone #: ___

Overview

Altronix Trove Plus kits are pre-wired, pre-assembled and consist of Trove1M1 enclosure/backplane with factory installed Altronix power supply/charger and sub-assemblies, wire harnesses and finger duct.

Configuration Chart






Altronix Model Number

| ****




115VAC

60Hz

Input Current (A)

| ****



Power Supply Board Input Fuse Rating

| ****



Power Supply Board Battery Fuse Rating

| Nominal DC Output Voltage| ****


Maximum Supply Current for Main Outputs on Power Supply board and ACM4(CB) Access Power Controller’s outputs

| Fail-Safe/Fail-Secure or Dry Form “C” Outputs| ACM4(CB) Board

Input Fuse (PTC) Rating

| ACM4(CB) Board

Output Fuse (PTC) Rating

| PDS8(CB) Board

Input Fuse (PTC) Rating

| PDS8(CB) Board

Output Fuse (PTC) Rating

---|---|---|---|---|---|---|---|---|---|---
Power Supply 1| Power Supply 2



Output Range (VDC)

| ****


Output Range (VDC)

T1M71LCK1| ****





3.0

| ****





5A/

250V

| ****





15A/

32V

| ****





20.17-

26.4

| ****





20.17-

26.4

| ****





24VDC @ 3.8A

| ****





4

| ****


10A/

250V

| ****


3A/

250V

| ****


10A/

250V

| ****


3A/

250V

T1M71LCK2
T1M71LCK3
T1M71LCK1D| ****


10A/

250V

| ****


2.5A

| ****


9A

| ****


2.5A

T1M71LCK2D
T1M71LCK3D

Installation Instructions

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Product is intended for indoor use only.

  1. Remove backplane from enclosure. Do not discard hardware.

  2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws; level and secure.
    Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and install the three fasteners.
    Place the enclosure’s upper keyholes over the three upper screws. Install the three lower screws and make sure to tighten all screws.

  3. Mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) in desired location, opposite hinge. Slide the tamper switch bracket onto the edge of the enclosure approximately 2” from the right side (Fig. 1, pg. 2). Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device. To activate alarm signal open the door of the enclosure.

  4. Mount Mercury modules to backplane(s), refer to page 3.

  5. Refer to the ULXB Power Supply/Charger Installation Guide for AL400ULXB2 and corresponding Installation Guides for PDS8(CB), VR6, and ACM4(CB) for further installation instructions.Altronix T1M1LCK1 Mercury Access and Power-fig2

T1M1LCK1(D): Configuration of Mercury Boards

  1. Position access controller module over corresponding spacers and depress onto snap on spacers (Fig. 3, pg. 4).
  2. Mount backplane to enclosure with hardware.

Access Controller Position Chart for the Following Models

Mercury Access Controller Pem Mounting
LNL-2220 / LP1502 / LP4502 A
LNL-1320 / MR52 B

Altronix T1M1LCK1 Mercury Access and Power-fig3 Altronix T1M1LCK1 Mercury Access and Power-fig4

T1M1LCK2(D): Configuration of Mercury Boards

  1. Position access controller module over corresponding spacers and depress onto snap on spacers (Fig. 3, pg. 4).
  2. Mount backplane to enclosure with hardware.

Access Controller Position Chart for the Following Models

Mercury Access Controller Pem Mounting
LNL-3300 / LP2500 A
LNL-1320 / MR52 B

Altronix T1M1LCK1 Mercury Access and Power-fig6 Altronix T1M1LCK1 Mercury Access and Power-fig7

T1M1LCK3(D): Configuration of Mercury Boards

  1. Position access controller module over corresponding spacers and depress onto snap on spacers (Fig. 3, pg. 4).
  2. Mount backplane to enclosure with hardware.

Access Controller Position Chart for the Following Models

Mercury Access Controller Pem Mounting
LNL-1320 / MR52 A
LNL-1320 / MR52 B

Altronix T1M1LCK1 Mercury Access and Power-fig9 Altronix T1M1LCK1 Mercury Access and Power-fig10

Trove1 Enclosure Dimensions

(H x W x D approximate): 18” x 14.5” x 4.625” (457mm x 368mm x 118mm)

Altronix T1M1LCK1 Mercury Access and Power-fig12 Altronix T1M1LCK1 Mercury Access and Power-fig13

140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
web site: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Altronix User Manuals

Related Manuals