HINKLEY 5054XX-CL Flash Mount Instruction Manual

: June 3, 2024
: HINKLEY

Table of Contents

HINKLEY 5054XX-CL Flash Mount
Mounting Instructions
wiring grounding instructions
- wiring instructions
grounding instructions
- Chain Hung Fixtures
HINKLEY
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HINKLEY 5054XX-CL Flash Mount

Mounting Instructions

HINKLEY-5054XX-CL Flash-Mount-FIG-1

Find a clear area in which you can work.
Unpack fixture and glass from carton.
Carefuly review instructions prior to assembly.

The construction of this fixture will be accomplished by first mounting the mounting strap to the junction box, making all necessary electrical connections, mounting the fixture to the wall and then in stalling the fixture glass.

HINKLEY-5054XX-CL Flash-Mount-FIG-2

Prepare mounting strap (A) by threading the two long mounting screws (B) into the back of the gull-wing bracket – see Drawing 1.
Be sure the holes into which the screws are threaded match the spacing of holes (D) in the back plate (E) – see Drawings 1 and 2. (not provided- see Drawing 2.
Attach mounting strap (A) to junction box () using two 1″ screws.

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (1.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEw WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

Make electrical connections from supply wire to fixture lead wires. Refer to the instruction sheet (1L.S. 18) and follow all instructions to make all necessary wiring connections. Then refer back to this sheet to complete installation of this fixture.

To mount fixture, slide backplate (E) over screws (B) and secure with ball knobs () -see Drawing.
To install glass remove the spacer (3) and socket ring (4) from the socket (1)-see Drawing 2.
Place glass (2) over the socket (1
Slip spacer (3) and thread socket ring (4) back on to socket (1) and hand tighten.
Note: Over-tightening could cause damage to the glass.
The fixture can now be lamped accordingly.

wiring grounding instructions

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (IS 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

wiring instructions

Indoor Fixtures

Connect positive supply wire (A ) (typically black or the smooth, unmarked side of the two-conduc tor cord) to positive ﬁxture lead (B) with an appropriately sized twist on the connector – see Drawings 1 or 2.
Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative ﬁxture lead (D).
Please refer to the grounding instructions below to complete all electrical connections.

Outdoor Fixtures

Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conduc tor cord) to positive ﬁxture lead (B) with an appropriately sized twist on the connector — see Drawings 2 or 3.
Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative ﬁxture lead (D).
The cover opens the end of connectors with silicone sealant to form a watertight seal. If installing a wall mount ﬁxture, use caulk to seal gaps between the ﬁxture mounting plate (backpla te) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a ﬁxture mounting platform specially.
Please refer to the grounding instructions below to complete all electrical connections.

grounding instructions

Flush Mount Fixtures

For positive grounding in a 3-wire electrical system, fasten the ﬁxture ground wire (E) (typically copper or green plastic coated) to the ﬁxture mounting strap (M ) with the ground screw (S) – see Draw in 1.

Note: On straps for screw supported ﬁxtures, ﬁrst install the two mounting screws in strap. Any remaining tapped hole may be used for the ground screw.

Chain Hung Fixtures

Loop ﬁxture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (S) on the ﬁxture mounting strap (M) and connect to the loose end of the ﬁxture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Draw in g 2.
Post-Mount Fixtures

Connect ﬁxture ground wire (E) (typically copper or green plastic coated) to power supply ground with an appropriately sized twist-on connector inside the post. The cover open end of the connector with silicone sealant to form a watertight seal – see Drawing 3.