HINKLEY 83527 Pendant Light Instruction Manual

: June 3, 2024
: HINKLEY

Table of Contents

HINKLEY 83527 Pendant Light
Mounting Instructions
wiring grounding instructions
- wiring instructions
grounding instructions
- Chain Hung Fixtures
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HINKLEY 83527 Pendant Light

HINKLEY-83527-Pendant-Light-product

Mounting Instructions

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

Shut off electrical current before starting. If the fixture you are replacing is turned on and off by a wall switch, simply turn the switch off. If not, remove the appropriate fuse ( or open the circuit breakers) until the fixture is dead.
- DO NOT restore current – either by fuse, breaker or switch – until the new fixture is completely wired and in place.
Fasten mounting strap (1) to outlet box (A) with two 8-32 screws (2) NOT PROVIDED – see Drawing 1.
Next thread 2 – hex nuts (3a) and (3b) onto threaded tubing (4).
Thread one end of threaded tubing (4) into loop (5) a minimum of 1/2’’ to 3/4’’. Tighten hex nut (3a) against loop (5) to lock loop in position.
Thread other end of threaded tube (4) into mounting strap approximately 1/2’’.
Slip canopy (B) over loop (5) and adjust height of loop so half of the threaded area on the loop is exposed – see Drawing 2 below. After loop height is adjusted, tighten hex nut (3b) up against mounting strap, tighten against mounting strap to lock loop and threaded tube in position.
Remove mounting strap (1) from junction box (A), and thread third hex nut (3c) onto end of threaded tube (4) above the mounting strap, tighten against mounting strap to lock assembly in position.
Taking the chain, determine the length you require to hang the fixture.
Attach one end of the chain to the top loop of the fixture.
Now slip loop screw collar (6) and canopy (B) onto chain – see Drawing 2.
Attach other end of chain to loop (5). Get assistance for the step since fixture may be heavy and difficult to hold while attaching the chain.
Unwarp the fixture lead wire and ground wire and weave them up through the chain.
Slip fixture lead wire and ground wire through center hole in loop (5).
Connect ground wire to mounting strap (1) using the green ground screw (GS).
Make electrical connections from supply wire to fixture lead wires. Refer to instruction sheet (I.S.18) and follow all instructions to make all necessary wiring connections.
Slilp canopy up to the ceiling and secure by turning the threaded screw collar (6) onto loop (5) and tighten to secure canopy to ceiling.

Note: quick connectors are used to secure chain to canopy. No chain pliers are required for assembly

wiring grounding instructions

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (IS 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

wiring instructions

Indoor Fixtures

Connect positive supply wire (A ) (typically black or the smooth, unmarked side of the two-conduc tor cord) to positive ﬁxture lead (B) with an appropriately sized twist on the connector – see Drawings 1 or 2.
Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative ﬁxture lead (D).
Please refer to the grounding instructions below to complete all electrical connections.

Outdoor Fixtures

Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conduc tor cord) to positive ﬁxture lead (B) with an appropriately sized twist on the connector — see Drawings 2 or 3.
Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative ﬁxture lead (D).
The cover opens the end of connectors with silicone sealant to form a watertight seal. If installing a wall mount ﬁxture, use caulk to seal gaps between the ﬁxture mounting plate (backpla te) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a ﬁxture mounting platform specially.
Please refer to the grounding instructions below to complete all electrical connections.

grounding instructions

Flush Mount Fixtures

For positive grounding in a 3-wire electrical system, fasten the ﬁxture ground wire (E) (typically copper or green plastic coated) to the ﬁxture mounting strap (M ) with the ground screw (S) – see Draw in 1.

Note: On straps for screw supported ﬁxtures, ﬁrst install the two mounting screws in strap. Any remaining tapped hole may be used for the ground screw.

Chain Hung Fixtures

Loop ﬁxture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (S) on the ﬁxture mounting strap (M) and connect to the loose end of the ﬁxture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Draw in g 2.
Post-Mount Fixtures

Connect ﬁxture ground wire (E) (typically copper or green plastic coated) to power supply ground with an appropriately sized twist-on connector inside the post. The cover open end of the connector with silicone sealant to form a watertight seal – see Drawing 3.

LARK