AMD Direct SSRFR-24DK 24 Inch 6.6c Deluxe Outdoor Rated Kegerator User Manual

AMD Direct SSRFR-24DK 24 Inch 6.6c Deluxe Outdoor Rated Kegerator

SAFETY AND INSTALLATION INSTRUCTIONS

WARNING Before the appliance is used, it must be properly positioned and installed as described in this manual, so read the manual carefully. To reduce the risk of fire, electrical shock or injury when using the appliance, follow basic precautions, including the following:

• Plug into a grounded 3-prong outlet, do not remove prong, do not use an adapter and do not use an extension cord.
•  Replace all panels before operating.
• It is recommended that a separate circuit serving only your appliance be provided. Use receptacles that cannot be turned off by a switch or pull chain.
• Never clean appliance parts with flammable fluids. These fumes can create a fire hazard or explosion.
• Do not store or use gasolines or other flammable vapors and liquids in the vicinity of this or any other appliance. The fumes can create a fire hazard or explosion.
• Do not connect or disconnect the electric plug when your hands are wet.
• Unplug the appliance or disconnect power before cleaning or servicing. Failure to do so can result in electrical shock or death.
• Do not attempt to repair or replace any part or your appliance unless it is specifically recommended in this manual. All other servicing should be referred to a qualified technician.

RISK OF CHILD ENTRAPMENT

1.  Child entrapment and suffocation are not problems of the past. Junked or abandoned appliances are still dangerous, even if they will “just sit for a few days.”
2. Before discarding your old refrigerator: Take off kegerator parts. Removing any hoses or fittings.

CAUTION

1. Stainless steel exposed to chlorine gas and moisture – such as areas with spas or swimming pools – may experience discoloration. This discoloration from chlorine gas is normal.
2. NEVER USE CHLORIDE TO CLEAN STAINLESS STEEL.

POWER FAILURE
Most power failures are corrected within a few hours and should not affect temperature of your appliance if you minimize the number of times the drawer is opened. If the power is going to be off for a longer period of time, take proper steps to protect the contents.

VACATION TIME
Short Vacations: Leave the appliance operating during vacations of less than three weeks.
Long Vacations: If the appliance will not be used for several months, remove all items and turn off the appliance. Clean and dry the interior thoroughly. To prevent odor and mold growth, leave the door open slightly, blocking it open if necessary.

MOVING YOUR APPLIANCE

• Remove all items.
• Securely tape down all loose items inside your appliance.
• Turn the adjustable legs up to the base to avoid damage.
• Tape the door shut.
• Be sure the appliance stays secure in the upright position during transportation. Also protect the outside of the appliance with a blanket or similar item.

GENERAL SAFETY REQUIREMENTS

ENERGY SAVING TIPS

• The appliance should be located in the coolest area of the room or outdoor location, away from heat-producing appliances and out of direct sunlight.
• Do not overload the beer dispenser as it forces the compressor to run longer.
• Position items so that air can circulate freely around them.
• Do not leave door open for longer than required.
• Make sure items do not touch the back of the storage compartment.
• Do not set the thermostat to exceedingly cold temperatures.

WARNING
FOLLOW WARNING CALLOUTS BELOW ONLY WHEN APPLICABLE TO YOUR MODEL

• Use two or more people to move and install appliance. Failure to do so can result in back or other injury.
• To ensure proper ventilation for your appliance, the front of the unit must be completely unobstructed.
• Choose a well-ventilated area with temperatures above 50°F (10°C) and below 109.4°F (43°C).
• The appliance should not be located next to ovens, grills, or other sources of high heat.
• The appliance must be installed with all electrical, water, and drain connections in accordance with state and local codes. A standard electrical supply (115 V AC only, 60HZ), properly grounded in accordance with the National Electrical Code and local codes and ordinances is required.
• Do not kink or pinch the power supply cord of the appliance.
• The size of the fuse (or circuit breaker) should be 1.3 amperes.
•  It is important that the appliance be leveled in order to work properly. You may need to make several adjustments to level it.
• All installations must be in accordance with local plumbing code requirements.
•  Never allow children to operate, play with or crawl inside the appliance.
• Do not use solvent-based cleaning agents or abrasives on the interior. These cleaners may damage or discolor the interior.
• Use this appliance only for its intended purposes as described in this instruction manual.
• Keep fingers out of the “pinch point” areas. Clearances between the drawer and cabinet are necessarily small. Be careful closing drawer when children are in the area.

BEFORE OPERATING

Important
BEFORE USING YOUR APPLIANCE
Remove the exterior and interior packing. Before connecting the appliance to the power source, let it stand upright for approximately 24 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation. Clean the interior surface with lukewarm water using a soft cloth.
Shipment Arriving Damaged:

VISIBLE DAMAGE
If your shipment arrives with visible damage to the box/carton, be sure the damage is noted on the bill of freight or express receipt and signed by the person making the delivery. File a claim for damages immediately, regardless of the extent of damage.

CONCEALED DAMAGE
If damages are unnoticed until the kegerator is unpacked, notify the transportation company or carrier immediately and file a concealed damage claim with them. This should be done within (5) days of the delivery date. Be sure to hold on to
the box/carton for inspection. We cannot assume responsibility for damage or loss incurred in transit.
Important Notes:

CONSTRUCTION ZONES
Keep all stainless steel products away from construction zones. Construction debris such as
(but not limited to) stone dust, stucco, and lime dust could damage or permanently discolor stainless steel products. Keep all caustic chemicals including chlorine and pool cleaning products away from stainless steel at all times.

WARNING
ELECTRICAL PARTS & COMPONENTS
Disconnect all power supplies and batteries before servicing.

INTERIOR LIGHT
This unit is equipped with an interior LED light which will be turned ON when the door is open and the interior fan is stopped at the same time. You can press to manually turn on or turn off the light.

DEFROSTING
The unit defrosts automatically in normal operating conditions. The evaporator behind the rear wall of the unit defrosts automatically. The condensation collects in the drainage channel behind the rear wall of the unit and flows through the drainage hole into the drop tray by the compressor where it evaporates. However, frost may accumulate on the evaporator
if the unit is repeatedly opened in a high heat or high humidity location. If this frost pattern does not clear within 24 hours, your unit will require manual defrosting.
Press and hold for 6 seconds to defrost the unit. To stop defrosting, repeat the same interaction.

TEMPERATURE ALARM
An audible alarm sounds if the storage temperature is not cold enough. The temperature display flashes at the same time.
The cause of the temperature being too high may be:

• Too much warm ambient air flow when rearranging and removing stored items.
• Prolonged power failure.
• The appliance is faulty.

The audible alarm is automatically silenced and
the temperature display stops flashing when the temperature is sufficiently cold again.

CLEANING AND MAINTENANCE
Periodic cleaning and proper maintenance will ensure efficiency, top performance and long life.
The maintenance intervals listed are based on normal conditions. You may want to shorten the intervals if you have pets or other special considerations.
Exterior cleaning for your stainless steel model:

• Turn off the power, unplug the appliance, and remove all items – including the dispense kit. Wash the inside surfaces with warm water and baking soda solution. The solution should be approximately 2 tablespoons baking soda by 1 quart water.
  Wring excess water out of sponges or cloths when cleaning controls or electrical parts.

• Wash the outside cabinet with warm water and mild liquid detergent. Rinse and wipe dry with a clean soft cloth.

• Do not use steel wool or a steel brush on the stainless steel. These will contaminate the stainless steel with steel particles and rusting may occur.

• Dust the front grill and back of the unit twice yearly, making sure the power is off before cleaning.

• It is recommended to clean the unit yearly, inside and out, to maximize the longevity of the product.

TROUBLESHOOTING

is turned off. The circuit breaker tripped or a fuse has blown out.
Kegerator is not cold enough| Check the temperature control setting. External environment may require a higher setting. The door is opened too often. The door is not closed completely. The door gasket is not sealing properly.
Kegerator is turning on and off frequently| The room temperature is hotter than normal. The door is opened too often. The door is not closed completely. The temperature control is not set correctly. The door gasket does not seal properly.
The light does not work| Not plugged in. The circuit breaker tripped or a fuse that the kegerator is plugged into has blown. The light bulb has burned out. The light button is “OFF”
Vibrations| Check to assure that the kegerator is on a level surface.
The kegerator seems to make too much noise| A faint humming noise may come from the flow of the refrigerant, which is normal. As each cycle ends, you may hear gurgling sounds caused by the flow of the refrigerant in your kegerator. Contraction and expansion of the inside walls may cause popping and crackling noises. During the defrosting process you may hear a water flowing sound caused by water flowing through the drain trough.The kegerator is not on a level surface.
The door will not close properly| The kegerator is not on a level surface. The gasket is dirty. The shelves are out of position.
Smell/Odor| Check for leaks on inside surface or around the keg coupler.
Outer surface of appliance is wet| Condensation has formed and can be wiped dry.
External surface is warm| Compressor is working to transfer heat from inside the cabinet.

You can solve many common problems easily, saving you the cost of a possible service call.
Reference the troubleshooting table below before calling the servicer.

Before Use:

Before connecting the unit to the power source, let it stand for approximately 24 hours. This will reduce the possibility of malfunction in the cooling system from handling during transportation.

1. Position the unit on a flat, level surface capable of supporting the entire weight of the unit. Remember the unit will be significantly heavier once it is fully loaded.
2. Connect the unit to a Ground Fault Interrupter (GFI).
3.  The unit must be installed according to your local codes and ordinances.
4. ELECTROCUTION HAZARD!
   • Electrical Grounding Required – This appliance is equipped with a three prong (grounding) polarized plug for your protection against possible shock hazards.
   • NEVER remove the round grounding prong from the plug.
   • NEVER use a two prong grounding adapter.
5. Remove the exterior and interior packaging, but do not remove any foam insulation surrounding the pipes at the back.
6. Clean the interior surface with lukewarm water using a soft cloth.
7. Place the unit on a flat, solid floor that is strong enough to support it when it is fully loaded. To level the appliance, adjust the rolling casters at the bottom of the unit.
8. When moving your kegerator, please do not incline it more than 45 degrees.
9. and sources of heat (stove, heater, radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption. Extreme cold ambient temperatures may also cause the unit to perform improperly. The optimal ambient temperature range is 50°F- 109.4°F. Do not mount the draft tower remotely, as the exposed beer line will not be refrigerated, causing foam.
10. Avoid locating the unit in damp areas.
11. Unwind the power cord to its full length and inspect for damage before plugging into the outlet. Plug the kegerator into an exclusive, properly installed and grounded wall outlet.
12. Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or electrical grounding should be directed to a certified electrician or authorized products service center.
13. After plugging the appliance into a wall outlet, allow the unit to cool down for 3 to 4 hours before installing a keg in the appliance.

It is recommended that you install the appliance in a place where the ambient temperature is between 50°F and 109.4°F (10°C-43°C). If the ambient temperature is above or below recommended temperatures, the performance of the unit may be affected. For example, placing your unit in extremely cold or hot conditions may cause interior temperatures to fluctuate. The operating temperature range may not be reached.

OPERATING YOUR APPLIANCE

CONTROL PANEL

ON/OFF POWER
To turn the appliance ON or OFF, press and hold the POWER key for 5 seconds.

UP AND DOWN
SETPress first, then press or button
to increase (warm) or decrease (cool) the set temperature by 1°C/ 1°F. shows the actual temperature. If no other further operation in 6 seconds, display will show actual temperature in the cooler

°F/°C SELECTOR
Selects the temperature display setting in Fahrenheit or Celsius degrees. To change the temperature from Fahrenheit to Celsius or from Celsius to Fahrenheit, SETpress and at the same time, then hold for 6 seconds.

SETTING THE TEMPERATURE CONTROL
The temperature you are setting will increase by one degree each time you press the key and will decrease by one degree each time you press the key.
The range of temperature control is from 32°F to 50°F.
To view the set temperature at any time, press
the kSET ey. The set temperature will flash in the display window for 6 seconds. After 6 seconds, the temperature inside the until will reappear in the display window.
(The temperature preset at the factory is 36°F)

OPERATION INSTRUCTION
The Kegerator is able to maintain the proper dispensing temperature for beer, provided it is installed correctly in the proper environment. For best results, mount the draft tower as close to the top of the kegerator as possible and seal any openings to prevent heat transfer. Avoid opening and closing the door of the kegerator too often to ensure a consistent temperature inside the unit. Factory preset temperature is 36 degrees Fahrenheit.
The Kegerator should be placed in an area where the ambient temperature range is between 50-109.4 degrees Fahrenheit (10-43 degrees Celsius). If the ambient temperature is above or below this range, the performance of the unit may be affected. For example, placing your unit in extreme cold or hot conditions may cause interior temperatures
to fluctuate. Please be aware that the desired temperatures may fluctuate depending on the ambient temperature and the orientation of the keg.

INSTALLATION

• STEP 1
  Unpackage your kegerator and lay out the kegerator parts on a flat surface, ensuring you have the following:
  

  • 1. CO2 Regulator
  • 2. Keg Coupler
  • 3. Keg Tap & Handle
  • 4. CO2 Tank
  • 5. Keg Tower w/Hose
  • 6. Red Hose w/ 2 Fasteners
  • 7. 4 Short Bolts &
  • 4 Metal Washers
  • 8. 4 Long Bolts, 4 Nuts &
  • 2 Rubber Washers
  • 9. Tap Tray
  • 10. Keys

• STEP 2
  Then, guide the translucent hose through the kegerator opening, or if you have an island, as shown, guide it through both openings. If mounting to a counter- top, secure your tower using the four long bolts & nuts, and 2 rubber washers. If mounting directly onto your kegerator, use the 4 short bolts and metal washers.
  

• STEP 3
  Now, screw the tap handle onto the Keg Tap, and fasten the Keg Tap to the tower by rotating counterclockwise.

• STEP 4
  Locate the translucent hose connected to the Keg Tower, and attach it to the Keg Coupler. Then, connect the Keg Coupler to your keg by pushing down and twisting clockwise to lock it in.
  DO NOT PUSH DOWN THE BLACK LEVER ON KEG COUPLER
  

• STEP 5
  Then, attach the regulator to the CO2 tank, using an adjustable wrench to avoid leakage. Place a metal fastener around the neck of the red hose, and attach the hose to the nozzle of the regulator. Tighten the fastener using a flathead screwdriver. Place another metal fastener around the other end of the red hose, and attach to the nozzle on the Keg Coupler. Tighten the metal fastener. Twist counterclockwise to open the CO2 tank. Unscrew the pressure valve until loose, and then re-screw until the pressure gauge reads “12”
  

• STEP 6
  Place your CO2 tank onto the shelf, and then lift the keg into the kegerator. Tap your keg by pulling out the black lever of your Keg Coupler, pushing down, and releasing. Make sure your keg completely cools before use. Place the Tap Tray below the tap.
  POUR AND ENJOY!
  

REPLACE ALL PANELS BEFORE OPERATING
This appliance should be properly grounded for your safety. The power cord of this appliance is equipped with a three-prong plug which mates with a standard three-prong wall outlet to minimize the possibility of electrical shock.
Do not under any circumstance cut or remove the third (ground) prong from the power cord supplied. For personal safety, this appliance must be properly grounded. Any questions concerning power and/or grounding should be directed toward a certified electrician or an authorized service center.
The appliance requires a standard 115/220 Volt AC-60HZ three-prong grounded electrical outlet. Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded. When a standard 2-prong wall outlet is encountered, it is your responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
To prevent accidental injury, the cord should be secured behind the appliance and not left exposed dangling.
The appliance should always be plugged into
its own individual electrical outlet which has a voltage rating that matches the rating label on the appliance. This provides the best performance and also prevents overloading house wiring circuits that could cause a fire hazard from overheating. Never unplug the appliance by pulling on the power cord, always grip the plug firmly and pull straight out from the receptacle. Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks
or abrasion damage along its length or at either end. When moving the appliance, be careful not to damage the power cord.
WARNING Improper use of the grounded plug can result in the risk of electrical shock. If the power record is cord is damaged, have it replaced by a qualified or an authorized service dealer.

EXTENSION CORD
Because of potential safety hazards under certain conditions, it is strongly recommended that you
do not use an extension cord with this appliance. However, if you must use an extension cord it is absolutely necessary that it be a UL/CUL-Listed,
3-wire grounding type appliance extension cord having a ground type plug and outlet and that the electrical rating of the cord be 115 volts and at least 1.3 amperes.

INSTALLING THE STAINLESS STEEL HANDLE

This appliance includes a stainless-steel handle that is not required to operate this unit. To install the handle please follow the below instructions:

1. Pull away the door gasket in the area where the handle is to be installed as shown in illustration. The gasket is easily displaced by hand, no tools are necessary.
2. Locate the screws included in the bag with the user’s guide. Insert the screws into the holes as shown.
3. Align the handle with the screws installed. Tighten the screws using a Phillips head screwdriver until the handle sets both flush and secured tightly against the door frame. (DO NOT overtighten as this will cause damage to the handle assembly).
4. Replace the door gasket to its original Position.

GOLD STANDARD WARRANTY

Your investment in AMD Direct product is backed by the strongest warranty in the industry. In addition to precision engineering and outstanding performance, AMD Direct products include our GOLD STANDARD LIFETIME WARRANTY with all replacement parts 100% non-prorated. Effective with purchases 8/1/21.
AMD Direct Warranty is valid for original purchaser at original site of delivery with proof of purchase and photo documentation only. Registration form must be submitted online within 30 days of the purchase date to validate the warranty. Warranty is void upon transfer of ownership. Warranty does not apply to products installed in any commercial, rental, or nonresidential application (exception of the Resort Grill, Alturi, & TRL). Warranty covers replacement parts only. Manufacturer is not responsible for labor or labor- related costs. Warranty does not cover discoloration, surface rust, corrosion, or oxidation, which may occur due to harsh environments, chemicals, or overheating. Warranty will not apply for damage resulting from improper installations, abuse, extreme environments, grease fires, or misuse. Proof of regular and proper maintenance is required. Coastal, humid, and/or salt environments are subject to manufacturer review. All out-of-box claims must be made within 30 days of purchase and must be made prior to installation. Any product installed damaged will be considered damaged during installation and not covered under warranty. Warranty and registration forms are available at www.amddirect.com/register. Please be advised – all display models are sold “as is” and the warranty covers the following items only: main burners (Gold Standard Lifetime Warranty), grates (Gold Standard Lifetime Warranty), burner covers (Gold Standard Lifetime Warranty). All warranties are subject to the review and approval of the manufacturer.

AMD DIRECT GAS APPLIANCES
GRILLS, SIDE/POWER BURNERS, & OVEN 

• Gold Standard Lifetime Warranty on stainless steel construction
• Gold Standard Lifetime Warranty on cooking grates, burners, burner covers, valves, flame tamers, and heatzone separators, temperature gauges, & hood springs
•  Gold Standard Lifetime Warranty on briquette systems
• 3 YEAR Warranty on all other parts, components, & electrical, including: LED bulbs, wire harness, & switches; power source wire; transformer; interior halogen light wire & bulb

VENT HOODS, REFRIGERATION, COLD STORAGE & SINKS
VENT HOODS

• 5 Year Warranty on all Stainless Steel Construction

• 3 year Warranty on blowers, LED Lighting, wiring harness and switches

• 15″ & 24″ REFRIGERATION MODELS

•  3 year Warranty on all construction including compressors

• 1 year Warranty on transformer, LED bulbs, LED harness, power source wire, LED switches, interior halogen light wire/bulbs
  21″ REFRIGERATION MODELS

• 1 year Warranty on all construction & electrical components including compressor, transformer, LED bulbs, LED harness, power source wire, LED switches, interior halogen light wire/bulbs
  COLD STORAGE & SINKS

• Gold Standard Lifetime Warranty on Ice Chests

• Gold Standard Lifetime Warranty on drains & faucets

DRAWERS, DOORS, GRILL LINERS, & CARTS

• Gold Standard Lifetime Warranty on construction, workmanship and materials for all stainless steel parts, including doors, drawers, grill liners, & carts
• 3 year on electrical (Warming Drawers)

COVERS

• Gold Standard Lifetime Warranty on covers, including grills, carts, side/power burners & oven

MADERA PRODUCTS

• Gold Standard Lifetime Warranty on construction, workmanship and materials for all stainless steel parts, hinges, drawer slides, gasket, & magnets

COMMERCIAL APPLICATIONS
RESORT, ALTURI & TRL GRILLS

• Gold Standard Lifetime Warranty on workmanship, construction, & manufacturer defects for all commercial and/or hospitality applications
• Warranty is void upon misuse, including lack of regular cleaning, vandalism, or theft
• Warranty is valid only if regular maintenance is exercised. Due to the nature of commercial applications (multiple users, lack of control of use, etc.) regular maintenance is mandatory

References

• AMD Direct
• Register — AMD Direct
• Register — AMD Direct

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>