ion4x Wi-Fi 6 2×2 Outdoor Access Point User Guide
- June 3, 2024
- iO
Table of Contents
ion4x Wi-Fi 6 2×2 Outdoor Access Point User Guide
Introduction
Thank you for purchasing our ion4x Access Point. ion4x is a cloud-managed 2×2:2 MU-MIMO Wi-Fi 6 certified Access Point that raises the bar for wireless performance and efficiency.
Packaging Content
ion 4x Specifications
Peak Throughput(aggregate)| Up to 1.78 Gbps (1202 Mbps for 5 Gliz and 574 Mbps
for 2.4 GHz)
---|---
VA-F1Standard Support| 802.11a/b/g/n/actec Wave 2/ax
Interface| 1 X 10/100/1000 BASET Ethernet
1 X 2500 Base X Optical Ethernet SFP
Radio Mode| 2×2 MU-MIMO wtth 2 spatial streams
Mesh Support| Self-creating. Self-heeling EasyMesh
Maximum number of SSID (per radio)| 16
Maximum User Support
1024 clients per Access Pant (512 clients per radio)
Power Supply| IEEE 802.3at PoE/PoE.
Power Consumption (Max)| 17 W (approx.)
Max Transmit Power| 30 d8m for 2.4 GHz .30 dam for 5614z (will depend on
countrpspeafic guidelines)
Antenna Type| Integrated directional antennas with 90′ beamwidth
Antenna Gain| 8 OBI for 5 GH2.8 del for 2.4 Gitz
Management| Standalone (via GUI) or through on premise based solution or
cloud-based
Enclosure Dimensions| 182 x 102 x 89 minor 7.17 x 7.17 x3.5 inches
Weight| 0.9 kg
Operating Temperature| -15’C to FOC
Certifications| FCC Class A, CE, Passpoir4 2.0, EasyMesh. WPM. IP67. MSS 3.0
Product Overview
Mounting of ion4x Access Point
The ion4x can be mounted on a pole or to a wall. Perform the following steps for appropriate installation.
- Align L Plate with the holes at the back of Access Point
- Use the provided screws to fix the plate onto the Access Point. The mounting bracket is fixed onto the mounting holes on the Access Point
Pole Mount
-
Align the L Plate mounted Access Point with pole clamp & U-Bolt
-
Pass the U-Bolt through the cuts of pole clamp & L Plate.
Secure it in place with Hex Nuts. -
Access Point has the freedom of movement along won the vertical horizontal axis
-
The final alignment of Access Point on a pole mounting as shown below
Note: The pole mounting is designed for Kies of diameter 40 mm to 60 nvn. For mountings on larger size poles WO 140 mm. contact at iosales@hfcl.com
Wall Mount
To mount the ion4x on a wall, use the wall mounting bracket, drywall screws, and screw anchors (* The entire wall mounting assembly is sold seperately).
- Take the reference from the wall mounting bracket and mark the position of the holes on the wall.
- Use the drill machine to drill 2 holes on respective marked positions.
- Push the screw anchors into the holes with a hammer.
- Align the drilled holes with the holes of wall mounting bracket.
- Insert the drywall screws through the holes of mounting bracket into the wall.
- Wall mounting bracket is fixed to the wall.
- Mount the device on to the wall mounting bracket as discussed in pole mounting process.
WARNING: HFCL is not held liable for any damages incurred during the process.
Getting the ion4x Online
Step 1:Power up
The Access Point can be powered up u as shown below:
Note: Plug and Adaptor will vary by country/ region.
Power up using PoE Adaptor
Step 2: Connect to the network
Section 1: Standalone
| AP Follow the steps mentioned below and connect the Access Point to a network |
|---|
-
Connect an ethernet cable to the computer.
-
Connect the other end of ethernet cable to the data port on PoE adapter (48V)
-
Connect ion4x PoE supported ethernet port to PoE adapter power port. Device will be powered on
-
Configure the computer with a same domain static IP 192.168.1.X and a subnet mask of 255.255.255.0 (X is from 2 to 255)
-
Open the web browser and enter the Access Point static IP address in the address bar: 192.168.1.1
-
A login screen will appear.
-
Enter the default login credential details: User- root, Password- hfd!@ion
**Section 2: Controller Managed AP
**
Follow the steps mentioned below and connect the Access Point to a network:
- Power-up the AP through PoE adapter or PoE switch
- Connect the AP to DHCP network and Internet
- Login to HFCL 10 cloud controller (cNMS) cnms.ionetworksin with credentials provided
- Refer our website io.hfd.com for detailed information to configure AP through cNMS
Step 3: Check the LED status
| LED Color | Status |
|---|---|
| Power LED Green | Green color notifies the user that the device is powered ON |
| 2.4 GHz Status LED | Solid blue color notifies the user that the 2.4 GHz radio |
is active and blinks while data is being transmitted on 2.4 GHz radio
5 GHz Status LED| Solid blue color notifies the user that the 5 GHz radio is
active and blinks while data is being transmitted on 5 GHz radio
Safety Precautions
Observe the Idlowing safety precautions to avoid damage to the Jones Access Point:
Do not power the device during In:Potation
Keep away from high voltage cables
Do not power off the unit in the middle of an upgrade process
The gland should be ground lacing al the time
Do not open the enclosure
Fasten the device tightly
Make sure the earthing wire is connected properly to the earthing points.
Contact Us:
Email: iosupport@hfcl.com
Website: www.hfcl.com
www.io.hfcl.com
8, Commercial Complex, Masjid Moth,
Greater Kailash-ll, New Delhi- 110048
HFCL Limited All Rights Reserved. 10 Networks and the IO logo are registered
trademarks of HFCL Limited.
Specifications are subject to change without notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>