SEALEY CPS02 Car Port Shelter 3.3 x 7.5 x 2.9m Instructions
- June 3, 2024
- SEALEY
Table of Contents
CAR PORT SHELTER 3.3 X 7.5 X 2.9M
MODEL NO: CPS02
CPS02 Car Port Shelter 3.3 x 7.5 x 2.9m
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY
8 This is a temporary structure and is not recommended as a permanent
structure.
Choose your shelter’s location carefully. Check for overhead utility lines,
branches, etc. DO NOT install near rooves or other structures that may shed
snow, ice or excessive run-off onto your shelter. Keep away from electrical
wires!
Have an overview of all parts before attempting installation. Make sure all
components are available.
× DO NOT use this product in environments for which it is not intended (i.e.
extreme cold, high winds, extreme heat, heavy rainfall, etc).
Always wear safety glasses when assembling this product. Wear gloves when
working with tubing to prevent cuts or abrasions.
‰ WARNING! Anchors must be used with alI shelters. Covers should NOT be
installed untiI it has been properly anchored to the ground.
Proper anchoring and keeping cover tight and free of snow and debris, is the
responsibility of the consumer. Damages caused by improper anchoring are not
covered under warranty.
‰ WARNING! Keep all flame and heat sources away from the shelter fabric. The
fabric will burn if left in continuous contact with a flame source.
× DO NOT use open flames or cooking or heating devices inside or in close
proximity to the product, including all types of stoves, gas heaters, gas
lanterns, citronella torches, mosquito coils, etc.
‰ WARNING! In order to reduce risk of burning and avoid damage, DO NOT:- cook,
smoke, refuel or use any open flame devices in or around the shelter.- store
flammable liquids (gasoline, kerosene, propane, etc.) in the shelter.- operate
gas powered equipment in or around the shelter.
Keep open flames a safe distance away from the shelter.
× DO NOT use hard-edged tools or instruments, such as rakes or shovels, to
remove snow. These can cause punctures to the cover.
× NEVER start the engine of any vehicle or machine inside a closed shelter.
Ensure that there is adequate ventilation for starting engines and for any
work with paints, cleaners, etc.
× DO NOT use bleach, alkaline or harsh detergents for cleaning. Doing so will
damage the polycarbonate material. Soap and warm water are recommended.
This temporary shelter is intended to offer protection from damages caused by
the sun, light rain, light snow, tree sap, bird and animal excrement. DO NOT
use it to shield goods from high winds, heavy snow or ice storms. Only use it
for its intended use.
× DO NOT assemble in high winds.
INTRODUCTION
Allows for extra space quickly, a garage for cars/small commercial vehicles,
storage for boats, materials and machinery.
Constructed of corrosion resistant powder coated high quality steel frame work
and a heavy-duty tarpaulin made of a PE (polyethylene) material which is UV
resistant making for a durable and long lasting shelter. Included stake pegs
secure the shelter, a dirt skirt on both sides further protects against
crosswinds. A wide opening zip door which can be rolled up out of the way,
provides easy-access.
This item is heavy. Extra assistance must be provided at the delivery point to
help its safe delivery.
SPECIFICATION
Model No: ……………………………………………………….CPS02
Overall Size: (W xD x H) ………………………3.3 x 7.5 x 2.9M
ASSEMBLY
4.1. Assembly Preparation.
4.1.1. Place all parts from the packaging box in a cleared area and arrange
them on the ground in front of you.
4.1.2. Remove all packaging materials and place them back in the box. DO NOT
dispose of the packaging materials until assembly is complete. Check for
completeness and transport damages, refer to figs.1 and 2.
‰ WARNING! DO NOT place the product under trees from which hard fruit such
as apples, walnuts or heavy pine cones, etc., may fall.
4.1.3. Keep children away during assembly. This product contains small parts
which can be swallowed by children.
4.1.4. DO NOT attempt to assemble the product if any parts are missing.
4.1.5. At least 3 people are needed to complete the assembly as some of the
steps require heavy lifting.
‰ WARNING! DO NOT leave the shelter unattended during assembly. Otherwise,
personal injury or damage to the shelter may occur!
4.2. Assemble Roof Frame.
4.2.1. Using fig.2 as a guide assemble the roof frame.
4.2.2. Fit the eight roof strainers and tension them.
4.3. Fit Cover (Roof and Sides).
4.3.1. Pull the cover over the roof frame, make sure the cover fits properly
at the eaves and at the edge of the roof.
4.4. Fit Legs and Cross Braces.
4.4.1. Ensure that there are enough people to lift the weight of the roof and
cover.
4.4.2. Lift the roof and cover high enough to insert the legs first down one
side, then repeat for the other.
4.4.3. Pass the cross braces through the sleeves then refer to figs. 4 and 5
for the assembly of the middle leg brackets and figs. 6 and 7 and for the
assembly of the end leg brackets.
4.5. Fix Cover and Fit Ends.
4.5.1. Fix the cover to the frame by closing the velcro strips round the
poles. Then fit the toggles through the eyelets and round the frame, see
fig.8.
4.5.2. Use a ladder to fit the ends using toggles.
4.6. Fix Feet.
4.6.1. Bolt the feet on see fig.9 and use the pegs to secure the shelter to
the ground, see fig.10.
ENVIRONMENT PROTECTION
**** Recycle unwanted materials instead of disposing of them as waste. All
tools, accessories and packaging should be sorted, taken to a recycling centre
and disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we reserve
the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>