Smart Home I004560 Mirabella Genio Wi-Fi Pixel Oval Floor Lamp User Manual
- June 3, 2024
- Smart Home
Table of Contents
Smart Home I004560 Mirabella Genio Wi-Fi Pixel Oval Floor Lamp
TO ENSURE THE SAFE AND SATISFACTORY OPERATION OF THIS SET PLEASE READ THESE INSTRUCTIONS CAREFULLY AND RETAIN FOR FUTURE REFERENCE
SAFETY INFORMATION
- Remove the set from the packaging before connecting to a power supply.
- only use the adaptor that is supplied.
- Ensure that the cable is completely uncoiled whilst the set is in use.
- LED bulbs are non-replaceable.
PRODUCT INSTALLATION
When connecting the Floor lamp to the Wi-Fi controller, make sure the arrows
are aligned with each other. 
Wi-Fi pairing information (BK, EZ, and AP methods)
- Download “Mirabella Genio” App from the APP store or Google Play and register an account.
- Connect your mobile phone to a 2.4GHz Wi-Fi network. (Please note, that this unit does not support 5GHz Wi-Fi)
- Connect the Wi-Fi controller to the light, and the adaptor to the Wi-Fi controller
- Wait for the light to commence to blink.
If the Floor light does not start to blink when first powered on, Press and hold the ON/OFF button on the Wi-Fi controller until it starts to blink.
If you having difficulty connecting this lamp to the Genio APP, wait for 3 minutes and the lamp stopped working, you can control this lamp manually using the 3-button Wi-Fi controller.
Bluetooth BK method
Our latest genio smart Wi-Fi lighting range has a Bluetooth pairing assist
function, to take advantage of this function, please ensure that the Bluetooth
on your phone is turned on. Make sure the light is blinking fast (2 blinks per
second), Open the Mirabella Genio app, and tap on the plus symbol, The APP
will now automatically find the lights, once the app identifies the lights,
follow the instructions below finalize the pairing of the lights to the App
.
Fasting blinking EZ method (when the Bluetooth on the phone is turned off)
- Open the Mirabella Genio app, tap on the plus symbol.
- Select the Genio Tube light under the smart lighting, then follow the in-app prompts to connect the tube light to your app.
Slow blinking AP method (1 blinking per 2 seconds)
If the fasting blinking method didn’t work for you, please try the slow blinking AP method. While the light is fast blinking, press and hold the ON/OFF again and wait for the light to start blinking slowly (1 blink per second).
- Open the APP this time the reset the device’s first screen.
- Tap on EZ mode located in the top right-hand corner of the screen, and select AP Mode.
- Now Confirm indicator slowly blinking, tap Next, then Go to connect. The app should automatically take you to your Wi-Fi screen if it does not get out of the Genio app and go to your phone’s Wi-Fi screen page.
- Search for a Wi-Fi signal commencing with SmartLife_XXX, once found select it to complete the pairing process.
- If you cannot see the SmartLife-XXXX on the list, it means the light was not blinking slowly, please reset it and try again.
After you have connected to SmartLife_XXXX, return back to the Mirabella Genio app and it will commence the 0-100% countdown and connection process, once complete, your lights are now paired to the app.
Please pay attention to this screen to determent the cause of the time-out
error
If the light never stops blinking, there could be an issue with the Wi-Fi
controller, please check our online FAQ page before returning it if the light
stopped blinking, but is unable to progress to “register on the cloud” it
indicates a communication error with your router to our cloud service.
Please check our online FAQ page and ensure
- You enter the correct 2.4GHz Wi-Fi name and password
- The Wi-Fi controller is in a location with good Wi-Fi coverage, try moving it closer to the router
- 5Ghz Wi-Fi signal is turned off on the router (can be turned on after the device is connected)
- If you are using IOS 14, please ensure “local network” permission is turned on for Genio APP
FAQ
Q. I have an internet/power outage and the device went offline and does not
reconnect back online by itself.
A. Go to the device’s settings page (pencil or … icon), look for “remove
device” Remove it and reset the device, and pair it again through the app.
Q. the light doesn’t light up?
A. please make sure when connecting the Wi-Fi controller, the arrows are
pointed at each other
Also, try using a known working 12V DC 2A adaptor
If you still having issues with pairing after using the AP method, please check our online FAQ pages at www.mirabellagenio.com.au/faqs.
Mirabella International Pty Ltd
1 Mirabella Drive Tullamarine VIC. 3043 Australia t: 1800 636 528
e: genio@mirabella.com.au.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>