SPRT SP-L36 Portable Thermal Printer User Manual
- June 3, 2024
- sprt
Table of Contents
SP-RMT9 BT Portable Thermal Printer
User Manual
Beijing Spirit Technology Development Co., Ltd
www.sprt-printer.com
NOTICE
Please read this manual carefully before using the printer!
Notice of Safety
Be sure to use the specified battery and power supply provided by our company.
Otherwise it may cause fire, explosion or damage printer, meanwhile, the
battery also may be damaged.
Don’t put battery into the fire, don’t disassemble or heat the battery, don’t
be short circuit, it may cause fire, explosion or damage printer, meanwhile,
the battery also may be damaged.
If the printer would not be used for a long time, be sure to take off the
battery, otherwise the battery may leak liquid which is corrosive liquid, if
improper operation causes battery leak liquid, and it paste in the skin or
clothes, please rinse it by clean water, if paste in the eyes, please rinse
them thoroughly by clean water and see a doctor. Please do not open the paper
case cover when it is printing or just when printing is finished, do not touch
the printer head with hand or body, overheat may cause scald.
Notice of Using
Water or other liquid should not be spilled into the printer, also the printer
should not be appeared in the rain, or else may cause printer damage. Please
do not open the paper case cover when it is printing, otherwise the printer
may work improperly. If printer is using USB connection to work, should not
unplug the USB cable, or else some printing data may be lost. When printer is
using USB connection to work, the distance of communication should be within
10 meters, otherwise the printer doesn’t print or prints rubbish codes. Too
high(45℃)or too low(5℃) environment temperature and too high (85 %) or too low
(20 %) environment humidity both effect the printing quality. The printer
paper roll with poor quality or stored for too long time also may reduce the
printing quality even damage the printer. Under the black mark detecting
mode, the printer requires that the pre-printed black mark is accordant with
the printing rule of black mark (please refer to details in Chapter 4.2),
otherwise the black mark can not be detected correctly. Be sure to use up the
power of the battery before charge up it,as it can ensure the using life of
the battery.
Notice of Storing
The printer should be placed in such an environment that the temperature is
between-20℃ and 60℃, and the relative humidity is between 10% and 90%. If the
printer will be stored for a long time, please be sure to take out the
battery, otherwise may damage the battery and printer.
Normal thermal paper receipt can’t be kept too long, if you need to keep the
receipt for a long period, please choose long-term effective thermal paper.
The thermal paper should be keep away from high temperature environment and
point-blank sunshine, please store it where is away from light if it have been
open.
Declaration
This product is “A” grade. In a domestic environment this product may cause
radio interference in which case the user may need to perform practical
actions.
Chapter 1 Outer Appearance and Model No.
1.1 Outer Appearance
[CHARGE]: Battery Charging Indicator
[ERROR]: Error Indicator
[FEED]: Feed Button
[MODE]: Mode Button
1.2 Model No.
SP—RMT9
Support USB Interface
SP—T9BTDM Support USB and Bluetooth Interface
Chapter 2 Characteristic Specification
2.1 Printing Specification
Printer Method: Thermal line
Paper Width: 79.5± 0.5mm
Effective Printing width:72mm
Resolution: 8 dots/mm (203dpi)
Dots in each line: 576dots/line
Printing Speed: 80mm/s (Max)
Paper Thickness: 0.06-0.08mm
Printable
Content: GB18030(Chinese)
BIG5(traditional
Chinese), ASCII characters, self-defining character.
Barcode: 1D:UPCA,UPCE,EAN13,EAN8,CODE39,ITF25,CODABAR,CODE 93,CODE 128
2D: PDF417,QR CODE,DATA Matrix
2.2 Physical Parameters
Dimension (W×L×H): 105(L) X101(W) X46(H) mm
Physical Weight: 254g (excluding roll paper)
Paper Type: thermal paper 79.5mm x40mm(MAX )
Interface: USB, Bluetooth
Printing Head Life: 50km
2.3 Environment
Operating Temp: 0℃~50℃
Operating Humidity: 10%~80% ( relative humidity)
Storage Temp: -20℃~60℃
Storage Humidity: 10%~90% ( relative storage humidity)
2.4 other Specification
- Paper Loading Method: drop-in easy loading please refer to details in 3.1.2 Paper Roll Installation).
- Paper Tearing Method: Manually tearing
- Black Mark Location: available(details please see 4.2 pre-printed black mark manual).
- Paper End Sensor: when paper is out, the ERROR Indicator will constant on lighting, The buzzer rings when it is printing, and it will stop printing.
- Printing Control Command: ESC/POS compatible command set. (refer to
) - Power Supply: 7.4V/1500mAh rechargeable polymer lithium battery.
- Low Power Alarm: When the electric of battery will run out, the power indicator will be red to alarm.
- Battery Charging: quick charging ,it will be charged full about 3 hours;
- Battery Duration: under25% printing density ,at least 120 meters, the standby time is over 100 hours. (These parameters are just for reference, long term usage will cause the capacity decline, and can not ensure the time of printing.)
Chapter 3 Operation Method
3.1 Using Preparation
3.1.1 Battery Installation
- Put the battery into the battery slot.
- Install the battery cover.
3.1.2 Paper Roll Installation
- Hold both sides of the paper case cover, and open it.
- Pay attention to use paper that effective printing side is outside in the printing paper face when you install the new paper roll.
- Pull out a part of paper and put them in the middle of the paper out orifice.
- Shut down paper case cover and cut off the redundant paper
3.1.3 Others
Opening and closing the case instruction: Pls make sure the right and left
side are open or close at the same time.
Abnormal operation instructions: The outlet is not allowed to be blocked
Place the direction: When printing, hold it horizontally to ensure the
stability of the paper roll.
3.2 Basic function usage
3.2.1 Switch On
Press【POWER】button, the power indicator is on, about 1 second later you will
hear ‘one low one high ’prompt tone. The printer will turn into work mode when
loosen the【POWER】button. The battery indicator shows power of the battery.
3.2.2 Switch Off
Under status of switch on ,the printer will send out the prompt tone of ‘one
low one high ’ after pressed the【POWER】button for 1 second, the power
indicator go out, then loosen the【POWER】 button, the printer is off.
3.2.3 Paper Feeding (Manual Feeding)
Under the normal work status, press 【FEED 】 button, the paper feeding begins,
and stop when loosen 【FEED】 button. When the printer works in black mark mode,
press【FEED】button, the printer begins to feed paper and stops over the
position of black mark. If the paper is not the black mark paper, the printer
stops automatically after feeds paper for 30cm.
3.2.4 Self-Test
After receiving the printer, user can check its current setting and status at
anytime.
Self-test way is as below: Power off, then hold down the 【FEED 】 button and
press the power button at the same time. Then loosen the【FEED】button and power
button when you hear ‘one low one high ’prompt tone, the current setting and
status will be printed out.
3.2.5 Hexadecimal Printing
The function of hexadecimal printing is to print the information received from
host machine by hexadecimal numbers and corresponding characters. It will be
convenient to debug application.
Into hexadecimal printing: Power off, hold down the【MODE 】button and press the
power button at the same time. Then loosen the power button and press the
【FEED】button when you hear ‘one low one high’ prompt tone of power on. After
that you may loosen the 【MODE 】button and 【FEED】 button. The printer turns
into the hexadecimal printing mode and print the presentation.
Quit hexadecimal printing :The way to quit hexadecimal printing mode is switch
off the printer or press the 【FEED】button for three times. The printer will
also print the presentation which shows that the printer have quitted
hexadecimal printing mode.
3.2.6 Printer Parameters Setting
This function may set some simple printing parameters.
Entering parameter setting: Switch off, then hold down the 【MODE 】 button and
press the 【POWER】 button at the same time. Then loosen the 【POWER】button
and【MODE 】button when you hear ‘one low one high ’prompt tone. The printer
turns into the parameters setting mode. Print out the first item which can be
set parameters and the current numerical value. Please see details in the
appendix as below.
Quitting parameter setting: Hold down【MODE 】and【FEED 】buttons, then loosen
【MODE 】 button and 【FEED】 button. Saving the set parameter and exiting the
parameter setting mode. The setting parameters won’t be saved if you directly
press the 【POWER 】button to turn off the printer.
3.2.7 Battery Charging
The battery will run out after a period of usage. When it nearly runs out,
printer will give a alarm through the battery indicator flashing, at this
time, user needs to charge up the battery.
The charging method is as following: connecting the adapter to the power
socket with 220V, 50HZ, then plug the power charging plug to the power socket
of the printer, so the power charging begins.
During the course of power charging, the charging indicator 【CHARGE 】 goes
red, and 【CHARGE 】turns to blue when the charging is full. It takes about 3
hours to charge up the battery.
Using the printer during the course of charging power will make the charging
time go longer. It shows the failure if the charging indicator 【 CHARGE 】 goes
blue and red during the course of charging. Such as faulty installation of
battery, faulty contact of battery or internal temperature of battery is too
high or too low.
3.3 Printer Parameters Setting
Users can set more parameters by using the specified 〈T9 Setting
Tools〉software through computer. The setting includes: language、 font
、printing density 、default code page 、bluetooth device name and password etc.
The setting method please refer to the
3.4 Printer Interface Connection and Printing
3.4.1 USB Connection
The SP-RMT9 printer of standard accessories includes Mini USB cable which
connects printer. The USB type belongs to the slave device type.
3.4.2 Bluetooth Connection
Handheld device, laptop and other information terminal devices with Bluetooth
can drive SP-T9BTDM to print by the Bluetooth interface. SP-T9BTDM portable
printer
is compatible with Bluetooth2.0 & 4.0 standard. The effective communication
distance is 10meters. The Bluetooth of the printer belongs to the slave
device. The initial name of the printer is T9 BT Printer Printer, the initial
password is ‘1234’; users can change the printer name and password by using
- Switch on printer;
- Host device searches for the outer Bluetooth device;
- If there are other Bluetooth devices, please select SP-RMT9 BT Printer;
- Enter the password ‘1234’;
- Pairing finished.
Please see details in primary device Bluetooth function instruction for reference.
Notice:
- When pairing, please make SP-RMT9 BT switched on.
- Once the BT device is paired with the host successful, it can’t be paired with other Bluetooth device until it unconnected with the host one.
- The power indicator flashes after paired successful.
3.4.3 Function of Bluetooth Address Binding
Bluetooth Binding: once the printer remembers the device’s address, it only
can connect with the first device and can’t connect with others. So in this
case, if the printer needs to connect with other devices, user can delete the
remembered address or set the mode is not binding.
No binding: in this case, the printer can be searched or paired by other devices. So when the printer needs to connect with a fixed device, it would be better to bind address. Please see the details in help file of<T9 Setting Tools>
3.5 Indicator and Buzzer
There are four indicators, they are red and blue【CHARGE 】light, red【ERROR
】light, blue 【BATTERY 】indicator and blue【POWER】 indicator. The meanings of
each indicators are as below: 【POWER】indicator Light constant on: printer is
on, Bluetooth is with disconnect status Light flashing: printer is on,
Bluetooth is with connection status 【CHARGE 】indicator Blue light constant
on: charging is completed;
Red light constant on: in charging;
Blue and red lights on: there are some mistakes, please check whether the
battery should be good contact or not, and the temperature is normal or not.
【ERROR】indicator Constant on lighting: printer out of paper
Light flashing: printer has mistakes. Different types of mistake, different
ways of flashing
- The mistake can be automatically recovered when the indicator continuous flashing. Including the temperature mistake of printer head and opening of paper case cover.
Error| Description| The flashing way of 【ERROR】ERROR
---|---|---
Temperatur e of printer head| The temperature of printer head is too high, it will recover automatically when the temperature is normal|
Paper case cover of printer| The paper case cover is opened when it is printing. Close the paper case cover, it will recover automatically| - The mistake can’t be automatically recovered when the indicator flashing some times and constant on then cycle. The times of flashing means the type of mistake.
Error| Description| The flashing way of [ERROR] ERROR
---|---|---
Memory ERROR| The printer can’t work normally after the memory need to be read-write calibration|
Over voltage| The voltage of power is too high|
Owe voltage| The voltage of power is too low|
The CPU execution| The CPU execution to the wrong address|
Temperatur e detection circuit| Connection of temperature detection circuit connection error|
【BATTERY 】indicator
The battery indicator composed by three parts in order to show the battery
status.
Three parts light on: battery is high
Two parts light on: battery is medium
One part light on: battery is low
Minimum part flashing: battery is extremely low, it must be charged
Three parts flashing at same time: power supply should be over voltage
(external power supply without battery)
There is also a buzzer to indicate various status of the printer. The meanings
are as below:
One low one high: power on;
One high one low: power off;
Circulation continuous two lows: printer at mistakes status
3.6 Printer Interface Connection and Printing
3.6.1 USB Connection
The standard configuration of the SP-L36 printer is equipped with a standard
Type-C cable for connecting the printer with the main device. The USB of the
printer belongs to the type of slave device (DEVICE); the shape and pin
definition are as shown in the figure below:
Chapter 4 Other Information
4.1 Command Programming Manual
Printing Position: As the picture above, the black mark should be printed on
the right or left edge of the side of words.
Width range: width≥7mm
Height range: 4mm≤height≤6mm
Reflectivity of infrared ray : <10% (infrared ray reflectivity of other parts
of the black mark paper is>65%)
HPS: it is the distance between edges of black mark and loading position.
4.5mm≤Hps≤6.5mm
APPENDIX A
This appendix is the method of setting default parameters of printer by
buttons.
Setting instruction: Using 【MODE 】 button to choose setting item.
Pressing this button once, the setting item will go to the next and also print
out the current value of this item. Using 【FEED 】button to choose the setting
value of item. Press the button once, the setting value will go to the next.
Warning
This is a class A product. In the domestic environment, the is product may
cause radio interference, in which case the user may be required to take
adaptable measures.
Manufacture has right to amend the content of the instruction without prior
announcement!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>