HILTI TE 300-AVR Lightweight Demolition Hammer Instruction Manual

June 3, 2024
HILTI

hilti -logo TE 300-AVR

TE 300-AVR Lightweight Demolition Hammer

HILTI TE 300 AVR Lightweight Demolition Hammer-

HILTI TE 300 AVR Lightweight Demolition Hammer-fig1

HILTI TE 300 AVR Lightweight Demolition Hammer-fig2

Original operating instructions

Information about the documentation

1.1 About this documentation

  • Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product.
  • Observe the safety instructions and warnings in this documentation and on the product.
  • Always keep the operating instructions with the product and make sure that the operating instructions are with the product when it is given to other persons.

1.2 Explanation of symbols used
1.2.1 Warnings
Warnings alert persons to hazards that occur when handling or using the product. The following signal words are used:

DANGER
DANGER !

  • Draws attention to imminent danger that will lead to serious personal injury or fatality.

WARNING
WARNING !

  • Draws attention to a potential threat of danger that can lead to serious injury or fatality.

CAUTION
CAUTION !

  • Draws attention to a potentially dangerous situation that could lead to personal injury or damage to the equipment or other property.

1.2.2 Symbols in the operating instructions
The following symbols are used in these operating instructions:

| Comply with the operating instructions
---|---
****| Instructions for use and other useful information
| Dealing with recyclable materials
| Do not dispose of electric equipment and batteries as household waste

1.2.3 Symbols in illustrations
The following symbols are used in illustrations:

| These numbers refer to the illustrations at the beginning of these operating instructions.
---|---
3| The numbering reflects the sequence of operations shown in the illustrations and may deviate from the steps described in the text.
| Item reference numbers are used in the overview illustration and refer to the numbers used in the key in the product overview section.
| These characters are intended to specifically draw your attention to certain points when handling
the product.

1.3 Product-dependent symbols
1.3.1 Symbols on the product
The following symbols can be used on the product:

| Chiseling
---|---
| Chisel positioning
Icon| Protection class II (double-insulated)
Li-lon| Li-ion battery
| Never use the battery as a striking tool.
| Do not drop the battery. Never use a battery that has suffered an impact or is damaged in any other way.

1.4 Product information
hilti -logo products are designed for professional users and only trained, authorized personnel are permitted to operate, service and maintain the products. This personnel must be specifically informed about the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by untrained personnel or if used not in accordance with the intended use. The type designation and serial number are printed on the rating plate.

  • Write down the serial number in the table below. You will be required to state the product details contacting Hilti Service or your local Hilti organization to inquire about the product.

Product information

Breakers TE 300­AVR
Generation 1
Serial no.

1.5 Declaration of conformity
We declare, on our sole responsibility, that the product described here complies with the applicable directives and standards. A copy of the declaration of conformity can be found at the end of this documentation. The technical documentation is filed and stored here:
Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany

Safety

2.1 Safety instructions
The safety rules given in the following section contain all general safety rules for electric tools which, in accordance with the applicable standards, require to be listed in the operating instructions. Accordingly, some of the rules listed may not be relevant to this electric tool.

2.1.1 General power tool safety warnings
WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
Work area safety

  • Keep work area clean and well lit. Cluttered or dark areas invite accidents.
  • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
  • Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

  • Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
  • Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
  • Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
  • Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
  • When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
  • If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

  • Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
  • Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
  • Prevent unintentional starting. Ensure the switch is in the off‐position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
  • Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
  • Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
  • Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
  • If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

Power tool use and care

  • Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
  • Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
  • Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
  • Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
  • Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
  • Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
  • Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

Service

  • Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

2.1.2 Hammer safety warnings

  • Wear ear protectors. Exposure to noise can cause hearing loss.
  • Use auxiliary handles, if supplied with the tool. Loss of control can cause personal injury..
  • Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

2.1.3 Additional safety instructions
Personal safety

  • Use the tool only when it is in technically faultless condition.
  • Never tamper with or modify the tool in any way.
  • Always hold the tool securely by the grips provided. Keep the grips dry, clean and free from oil and grease.
  • Wear protective gloves also when changing the accessory tool. Touching the accessory tool presents a risk of injury (cuts or burns).
  • Take breaks between working and do physical exercises to improve the blood circulation in your fingers. Exposure to vibration during long periods of work can lead to disorders of the blood vessels and nervous system in the fingers, hands and wrists.
  • The tool is not intended for use by debilitated persons who have received no special training.
  • Keep bystanders, children and visitors away while operating a power tool.
  • Before beginning the work, check the hazard classification of the dust that will be produced. Use an industrial vacuum cleaner with an officially approved protection classification in compliance with locally applicable dust protection regulations.
  • Use a dust removal system and suitable vacuum cleaner whenever possible. Dust from materials, such as paint containing lead, some wood species,  concrete/masonry/stone containing silica, and minerals a well as metal, may be harmful.
  • Make sure that the workplace is well ventilated and, where necessary, wear a respirator appropriate for the type of dust generated. Contact with or inhalation of the dust may cause allergic reactions and/or respiratory or other diseases to the operator or bystanders. Certain kinds of dust are classified as carcinogenic such as oak and beech dust, especially in conjunction with additives for wood conditioning (chromate, wood preservative). Material containing asbestos may be handled only by specialists. Observe the national health and safety requirements.

Electrical safety

  • Before beginning work, check the working area for concealed electric cables or gas and water pipes. External metal parts of the power tool may give you an electric shock if you damage an electric cable accidentally.
  • Check the power tool’s supply cord at regular intervals and have it replaced by a qualified specialist if found to be damaged. If the power tool’s supply cord is damaged it must be replaced with a speciallyprepared and approved supply cord available from Hilti Customer Service. Check extension cords at regular intervals and replace them if found to be damaged. Do not touch the supply cord or extension cord if it is damaged while working. Disconnect the supply cord plug from the power outlet. Damaged
    supply cords or extension cords present a risk of electric shock.

Careful handling and use of electric tools

  • Secure the workpiece. A workpiece clamped in a vice or secured by some other clamping device is more secure than when held only by hand.
  • Ensure that the accessory tools used have a mounting system that is compatible with the power tool and that they are secured in the chuck correctly.
  • Switch the electric tool off and unplug the supply cord in the event of an interruption in the electric supply in order to avoid inadvertent restarting when the power returns.

Description

3.1 Overview of the product 1

HILTI TE 300 AVR Lightweight Demolition Hammer-fig3

  1. TE­C or TE­T chuck
  2. Function selector switch
  3. Control switch lock
  4. Control switch
  5. Grip
  6. Supply cord
  7. Front grip surface

3.2 Intended use
The product described is an electrically powered breaker. It is designed for light chiseling work on masonry and surface finishing work on concrete.

  • Operation is permissible only when connected to a power source providing a voltage and frequency in compliance with the information given on the type identification plate.

3.3 Active Vibration Reduction (AVR)
This product is equipped with an Active Vibration Reduction (AVR) system, which reduces vibration significantly.
3.4 Items supplied
Breaker, operating instructions.
**** Other system products approved for use with this product can be found at your local Hilti Store or at: www.hilti.group

Technical data

4.1 Breaker
When powered by a generator or transformer, the generator or transformer’s power output must be at least twice the rated input power shown on the rating plate of the power tool. The operating voltage of the transformer or generator must always be within +5% and -15% of the rated voltage of the power tool.
The information given applies to a rated voltage of 230 V. The data may vary in the event of deviations from the rated voltage and for country-specific versions. Please refer to the power tool’s rating plate for details of its voltage, frequency, current and input power ratings.

| TE 300­AVR
---|---
Weight in accordance with EPTA procedure 01| 3.8 kg
Single impact energy in accordance witEPTA procedure 05/2009| 3.3 J

4.2 Noise information and vibration values determined in accordance with EN 60745
The sound pressure and vibration values given in these instructions have been measured in accordance with a standardized test and may be used to compare one electric tool with another. They may be used for a preliminary assessment of exposure. The data given represents the main applications of the electric tool. However, if the electric tool is used for different applications, with different accessory tools, or is poorly maintained, the data may vary. This may significantly increase exposure over the total working period. An accurate estimation of exposure should also take into account the times when the tool is switched off, or when it is running but not actually being used for a job. This may significantly reduce exposure over the total working period. Identify additional safety measures to protect the operator from the effects of noise and/or vibration, for example: maintenance of the electric tool and the accessories, keeping the hands warm, organization of work patterns.
Noise emission values determined in accordance with EN 60745-2-6

Measured sound power level (LWA) 102 dB(A)
Uncertainty for the sound power level (KWA) 3 dB(A)
Sound pressure level (LpA) 91 dB(A)
Uncertainty for the sound pressure level (KpA) 3 dB(A)

Total vibration (vector sum of three directions), measured in accordance with EN 60745-2-6

Chiseling (ah, Cheq) 13.5 m/s²
Uncertainty (K) 1.5 m/s²

Operation

Fitting / removing the accessory tool

WARNING
Risk of injury! The accessory tool gets hot during use and may also have sharp edges.
▶ Wear protective gloves when changing the tool.| 2
---|---
Check the accessory tool for damage or uneven wear each time before use and replace it if necessary.
Use only the recommended grease supplied by Hilti. Use of unsuitable grease may cause damage to the product.
Removing / fitting the chuck| 3
Positioning the chisel | 4
** The chisel can be adjusted to 12 different positions (in 30° increments). This ensures that flat chisels and shaped chisels can always be set to the optimum working position.|
Locking the chisel|
Chiseling| 5
Fitting the needle adapter
CAUTION
Risk of injury! Use of the needle adapter in an incompatible tool is hazardous.
• Use the needle adapter only with the TE 300-AVR.| 6
---|---
WARNING
Risk of injury! Risk of pinching the fingers
• Wear protective gloves when fitting the needle adapter.| 7
Removing the needle adapter
WARNING
Risk of injury! The accessory tool gets hot during use and may also have sharp edges.
• Wear protective gloves when changing the tool.| 8
Selecting / adjusting the needle guide
WARNING
Risk of injury! The accessory tool gets hot during use and may also have sharp edges.
• Wear protective gloves when changing the tool.|
**
The needle guide is interchangeable and adjustable. Round or oval versions are available for working on surfaces, edges or corners.|
Changing the needle cage and needles
WARNING
Risk of injury! The accessory tool gets hot during use and may also have sharp edges.
• Wear protective gloves when changing the tool.| 9
**** The spring pre-tensioner separates the needle holder from the locking mechanism. The needles can be replaced individually or as a complete set.|

Care and maintenance

WARNING
Electric shock hazard! Attempting care and maintenance with the supply cord connected to a power outlet can lead to severe injury and burns.
• Always unplug the supply cord before carrying out care and maintenance tasks.

Care

  • Carefully remove stubborn dirt from the tool.
  • Never operate the product when the air vents are blocked. Clean the air vents carefully with a dry brush.
  • Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as these can attack the plastic parts.
  • Do not use a spray, pressure jet washer or running water for cleaning.

Maintenance

WARNING
Danger of electric shock! Improper repairs to electrical components may lead to serious injuries including burns.

  • Repairs to the electrical section of the tool or appliance may be carried out only by trained electrical specialists.
  • Check all visible parts and controls for signs of damage at regular intervals and make sure that they all function correctly.
  • Do not operate the electric tool if damaged or if its parts malfunction. Have the tool repaired by Hilti Service immediately.
  • On versions with a replaceable supply cord, the supply cord may be replaced by a trained electrical specialist.
  • After cleaning and maintenance, fit all guards or protective devices and check that they function correctly.

**** To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables and accessories approved by Hilti for use with the product can be found at your local Hilti Center or online at: www.hilti.com

Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by yourself, please contact Hilti Service.

Trouble or fault Possible cause Action to be taken
The breaker doesn’t start. Interruption in the electric supply. • Plug in

another electric tool or appliance and check whether it works.
No hammering action.| The power tool is too cold.| • Bring the tip of the accessory tool into contact with the working surface, switch the power tool on and allow it to run. If necessary, repeat the procedure until the hammering mechanism begins to operate.
The breaker doesn’t achieve full power.| The extension cord is too long or its gauge is inadequate.| • Use an extension cord of an approved length and/or of adequate gauge.
The control switch is not fully pressed.| • Press the control switch as far as it will go.
The chisel cannot be released from the chuck.| The chuck is not pulled back fully.| • Pull the chuck back as far as it will go and remove the accessory tool.

Disposal

Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative for further information.

  • Do not dispose of power tools, electronic equipment or batteries as household waste!

Manufacturer’s warranty

  • Please contact your local Hilti representative if you have questions about the warranty conditions.

EC Declaration of Conformity I UK Declaration of Conformity
Manufacturer:
Hilti Corporation
FeldkircherstraBe 100
9494 Schaan I Liechtenstein
TE 300-AVR (01)
Importer:
Hilti (Gt. Britain) Limited
1 Trafford Wharf Road, Old Trafford
Manchester, M17 1BY

Serial Numbers: 1-99999999999
2006/42/EC I Supply of Machinery (Safety) Regulations 2008 2014/30/EU I Electromagnetic Compatibility Regulations 2016
EN 60745-1:2009 + Al 1:2010 EN 55014-1:2017 + A11:2020
EN 61000-3-2:2019
EN 60745-2-6:2010 EN 55014-2:2015 EN 61000-3-3:2013 + Al :2019
2011/65/EU I The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 2000/14/EC I Noise Emission in the En-vironment by Equipment for use Outdoors Regulations 2001
Details to 2000/14/EC I Noise Emission in the Environment by Equipment for use Outdoors Regulations 2001: Measured sound power level LwA: Guaranteed sound power level, LwAd: Conformity assessment procedure:
EU Notified Body I UK Approved Body
102 dB/1pW 105 dB/1pW 2000/14/EC, Annex VI I Noise Emission in the Environment by Equipment for use Outdoors Regulations 2001, Schedule 9 TON/ NORD CERT GmbH, Langemarckstr. 20, 45141 Essen, Germany (CE 0044) HORIBA MIRA Certification Ltd, Watling Street, Nuneaton, Warwickshire CV10 OTU (No 0888)

HILTI-signature

hilti -logo

Hilti Corporation
L1-9494 Schaan
Tel.:+423 234 21 11
Fax:+423 234 29 65
www.hilti.grouphttps://hilti.to/ontrackapp

Hilti = registered trademark of Hilti Corp., Schaan
Pos. 8 | 20211103

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals