MystFlame EF28Z Smart Electric Fireplace User Manual

MystFlame EF28Z Smart Electric Fireplace

IMPORTANT SAFETY INFORMATION

WARNING

• Read all instructions before using this heater!
• This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided,use handles when moving this burning heate r. Keep combustibl e materials ,such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater, and keep them away from the sides and rear.
• Extreme caution is necessary when any heater is used near children or invalids and whenever the heater is left operating and unattended.
• DO NOT operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Discard heater, or return to authorized service facility for examination and/or repair.
• DO NOT run power cord under carpeting. DO NOT cover power cord with throw rugs, runners, or similar coverings. DO NOT route power cord under furniture or appliances. Arrange power cord away from traffic area, and where it will not be tripped over.
• DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause electric shock or fire, or damage the heater.
• To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. This could cause a fire. DO NOT use on soft surfaces, like a bed, where openings may be blocked up.
• A heater has hot and arcing or sparking parts inside. DO NOT use it in areas where gasoline, paint, or flammable liquids are used or stored.
• Use this heater only as described in this manual. Any other usage not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
• ALWAYS plug heaters directly into a wall outlet/receptacle. NEVER use with an extension cord or relocatable power tap (outlet/power strip).
• Connect to properly grounded outlets ONLY.
• DO NOT place the heater near a bed because objects such as pillows or blankets can fall from the bed and be ignited by the heater.
• NEVER use this heater in bathrooms, laundry rooms, or any other location where the heater could fall into a bathtub or pool, become damp, or touch the water.
• AVOID FIRE! Regularly inspect all air vents to make sure they are free from dust, lint, or other blockage. Unplug the unit and clean with a vacuum ONLY. DO NOT rinse or get wet.
• NEVER permanently install in a recessed area of the wall. This may result in blocked air flow, overheating, or fire.
• WARNING: DO NOT DEPEND ON THE POWER SWITCH THE SOLE MEANS OF DISCONNECTING POWER WHEN SERVICING OR MOVING THE HEATER. ALWAYS UNPLUG THE POWER CORD.
• WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK—DO NOT USE THIS HEATER WITH ANY SOLID STATE SPEED CONTROL DEVICES.
• For residential use only! NOT for commercial use! Any commercial or public use of this heater voids all warranties, and could cause injury.
• This product is not intended to be a primary heat source. It is for supplemental heat only.
• INDOOR use only! NEVER use this heater outdoors! Doing so may result in electric shock!
• Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside!
• NEVER modify this heater. Doing so could result in personal injury or property damage. Modification of this fireplace completely voids all warranties.
• ALWAYS turn this heater off before unplugging it from the outlet.
• ALWAYS disconnect this unit from the power supply before performing any assembly or cleaning, or before relocating the electric fireplace.
• NEVER leave this heater unattended. ALWAYS unplug this heater when not in use.
• ALWAYS store this heater in a dry location. NEVER use the fireplace if it has become wet.
• ONLY use this heater on a 120V AC 15-Amp circuit. NEVER overload the circuit. If this heater trips the circuit breaker, unplug all other appliances on the same circuit before the next use. Avoid plugging other appliances into the same circuit as this heater.
• NEVER plug this heater into an outlet that is old, cracked, or has any loose wires or connections. Plugging this heater into a faulty outlet could result in electric arcing within the outlet that could cause the outlet to overheat or catch fire.
• ALWAYS check your heater cord and plug connections with each use!
• MAKE SURE the plug fits tight in the outlet! Faulty wall outlet connections or loose plugs can cause the outlet to overheat.
• Heaters draw more current than small appliances. Overheating may occur even if it has not occurred with the use of other appliances.
• During use check frequently to see if the plug outlet or faceplate is HOT!
• If the outlet or faceplate is HOT, discontinue use immediately and have a qualified electrician inspect and/or replace the faulty outlets.
• This heater has a polarized plug (one blade is wider than the other). As a safety feature to reduce the risk of electrical shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
• SAVE THESE INSTRUCTIONS!

PREPARATION

DO NOT use this Electric Fireplace if any part has been under water. Immediately call a qualified service technician to inspect and to replace any part of the electrical system if necessary. Keep plastic wrapping away from children.

Unpacking the Electric Fireplace. Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Check the parts list to make sure nothing is missing. Dispose of packaging materials properly. Please recycle whenever possible. Keep the original packaging for future transport and/or storage.

PRODUCT DIMENSIONS

Model

| Width

（ W ）

| Height

（ H ）

| Depth

（ D ）

| Advise mantel opening size| Advise mantel minimum depth

（ RD ）

---|---|---|---|---|---
Width

（ OW ）

| Height

（ OH ）

EF28Z| 762| 650| 225| 745-755| 644-648| 215-220
EF30Z| 838| 650| 225| 820-825| 644-648| 215-220
EF33Z| 915| 650| 225| 905-910| 644-648| 215-220
EF33WZ| 915| 487| 225| 905-910| 481-485| 215-220

Model

| Width

（ W ）

| Height

（ H ）

| Depth

（ D ）

| Advise mantel opening size| Advise mantel minimum depth

（ RD ）

---|---|---|---|---|---
Width

（ OW ）

| Height

（ OH ）

EF28Z| 30.0| 25.59| 8.86| 29.33-29.72| 25.4-25.5| 8.47-8.66
EF30Z| 33.0| 25.59| 8.86| 32.28-32.48| 25.4-25.5| 8.47-8.66
EF33Z| 36.0| 25.59| 8.86| 35.63-35.83| 25.4-25.5| 8.47-8.66
EF33WZ| 36.0| 19.18| 8.86| 35.63-35.83| 18.94-19.1| 8.47-8.66

ASSEMBLY

• ALWAYS unplug this fireplace heater before assembly or cleaning, or before relocating. Failure to do so could result in electric shock, fire, or personal injury.
• KEEP drapery and other furnishings at least 3ft /0.9m from the front and sides of the electric fireplace.
• AFTER installation, ensure that there is ≥0.004 ㎡ ventilation area between inside and outside of fireplace mantel.
  Your new electric fireplace may be installed virtually anywhere in your home. However, when choosing a location ensure that the general instructions are followed. For best results, install out of direct sunlight. Power supply service must be either completed or placed within the electric fireplace prior to finishing to avoid reconstruction.

When moving the insert into mantel, Do not let bottom of insert touch the mantel to avoid the scratch.
BATTERY REPLACEMENT
NOTE: The remote control not include the batteries.
NOTE: Do not mix old and new batteries.
Do not mix alkaine,standard(carbon zinc),or rechargeable(nicad,nimh,ect.)batteries.

OPERATION

Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Fail to do so could result in e lectric shock, fire, serious injury, or death.

Power

Make sure the Power Switch, located on the control panel, is in the OFF position. Plug the power cord into a 110~120 Volt 15 Amp outlet (see IMPORTANT SAFETY INFORMATION on Pages 3 and 4). Make sure the outlet is in good condition and that the plug is not loose. NEVER exceed the maximum amperage for the circuit. DO NOT plug other appliances into the same circuit.
Temperature Limiting Control
This heater is equipped with a Temperature Limiting Control. Should the heater reach an unsafe temperature, the heater will automatically turn OFF. To reset:

1. Unplug the power cord from the outlet.
2. Turn the Power Switch on the CONTROL PANEL to OFF. Wait at least 5 minutes.
3. Inspect the fireplace to make sure no vents are blocked, or clogged with dust or lint. If they are, use a vacuum to clean the vent areas.
4. With the Power Switch in the OFF position, plug the power cord back into the outlet.
5. If it switches off again, UNPLUG THE HEATER RIGHT AWAY! Have the outlets, wiring, and breaker box inspected by a professional. Make necessary repairs before using the heater.

Heater Rating

Maximum heat output: 1500W (5000BTU); Maximum heating area: 400 square feet.
Operation
Review the IMPORTANT SAFETY INFORMATION on Pages 3 and 4 before operating.

NOTICE
When the heater is first turned on, a slight odor may be present. This is normal and should not occur again unless the heater is not used for a long period of time.

Control Panel
Located on the right and top side panel of the fireplace.

Remote Control

NOTICE

Control panel Power Switch must be ON to use remote control.
Aim the remote control at the remote receiver. Make sure you hear a beep each time you press the button! If not, the fireplace will not respond to the signal.

NOTICE
Operation for all functions are same as the buttons on the fireplace.

CARE AND MAINTENANCE

ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in electric shock, fire, or personal injury.

Cleaning
NEVER immerse in water or spray with water. Doing so could result in electric shock, fire, or personal injury.

Metal
Buff using a soft cloth, slightly dampened with a citrus oil-based product.
DO NOT use brass polish or household cleaners as these products will damage the metal trim.

Glass
Use a good quality glass cleaner and dry thoroughly with a paper towel or lint-free cloth.
NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.

Plastic
Wipe gently with a slightly damp cloth and a mild solution of dish soap and warm water.
NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.

Vents

Use a vacuum or duster to remove dust and dirt from the heater and vent areas.
Clean the exterior of the fireplace with a slightly damp cloth or duster.

Maintenance

Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside!
ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in electric shock, fire, or personal injury.

Electrical and Moving Parts
The fan motors are lubricated at the factory and will not require lubrication.
Electrical components are integrated in the fireplace and are not serviceable by the consumer. Storage:
Store heater in a clean dry place when not in use.
Replacement parts
Use only replacement parts supplied by the manufacturer. Use of any other parts, or modifying the fireplace in any way, will void all warranties.
No internal parts are replaceable or serviceable.

WARNING  No other servicing should be performed by the consumer. Do not attempt to service the unit by yourself.

SCHEMATIC DIAGRAM

FAQ – FREQUENTLY ASKED QUESTIONS

• Why does the fan blow before the heat comes on, and after the heater is turned off?
  Heat and cool gradually. The fan blows when the heater is first turned on, and the heat is still heating up. After the heater turns off, the fan will continue to blow air for 10 seconds. This allows the fireplace to cool slowly, and helps prevent overheating.

• What does the fireplace beep? Can I turn the beeping off?
  The beeps indicate that the signal from the control panel, or remote control, has been received by the fireplace. The beeping cannot be turned off.

• Why doesn’t the fireplace function change when remote control setting changes?
  The fireplace function will only change if there is a beep after pressing the button. If you do not hear a beep, try again. If you hear a beep, the fireplace function will change to match the remote control setting.

• Why does the remote control not work, or only work sometimes?
  Check to make sure the batteries are good. If necessary, change to new batteries. If the remote control is not aimed properly, if you are too far away, or if you are too far off to the side, the signal may not reach the fireplace. Get closer, aim at the upper top corner of the screen (where the red heat indicator light is located), and try again.

• How do I change from high heat to low heater?
  The heater is controlled by the heater button on the control panel, or the heater buttons on the remote control.

• Is the thermostat setting accurate?
  The temperature within a room can vary. Room size, fireplace location, airflow, sunlight, wall type (interior vs. exterior), insulation, etc. all affect temperature. The fireplace setting may not match your home thermostat exactly. This is normal. Try different thermostat setting on your fireplace until you find one that is right for you.

TROUBLESHOOTING GUIDE

1.    Make sure the power cord is plugged into a functioning and properly grounded 15 Amp 120V AC electrical outlet.

2.    Make sure the Power Switch on the control panel is ON.

3.    If the unit had been working, but then turned off by itself, the temperature limiting control may need to be reset. See page 8 for instructions.

4.    Check for damage to the power cord or plug. If damaged, DO NOT USE.

The control panel functions do not work.| 1.    Make sure the Power Switch on the control panel is turned on.     If it is OFF, the functions will not work.

2.    If the Power Switch is ON, and the functions do not work, please contact us.

The    FLAME     button doesn’t work.| 1.    Make sure the Power Switch on the control panel is ON.

2.    If    the Power Switch is ON, and the functions do not work, please contact us.

The heater does not work.| 1.    Make sure the Power Switch on the control panel turned on.

2.    Control Panel: Press the heater button on the control panel to override the thermostat at any time.

3.    Remote control: Make sure the thermostat is not set too low. If the thermostat is set lower than room temperature, the heater will not turn on.

4.    If none of these solutions work, please contact us.

The heater does not blow hot air when it turns on and off.| This is normal. The fans blow cool air while the heater gradually heat up. The fans blow after the heater turn off to cool the heater and prevent overheating.
The remote control does not work.| 1.    Make sure the battery is properly installed.

2. Make sure the Power Switch on the control panel is turned on. The remote control will not work unless the POWER SWITCH on the control panel is turned on.

3.    Aim the remote control at the receiver.

4.    Remove objects that may be in the way. Items between the remote control and the remote control receiver will block the signal.

5.    Don’t press the remote control buttons too quickly. Give the unit time to respond to your commands.

The thermostat does not work.| 1. Make sure the heater is turned on. The thermostat will not work unless the heater is turned on.

2.    Make sure the thermostat is not set too low. If the thermostat is set lower than room temperature, the heater will turn on.

LIMITED WARRANTY

This warrants to the original purchaser that this product is free from defects in material and workmanship as of the date of purchase and that it will, under normal use and proper care, remain one year from the date of purchase. Missing or initially defective parts will be replaced free of charge during the period of this limited warranty. If parts are unavailable, a comparable replacement of refund will be given. The original dated sales receipt is required for all warranty claims. This warranty does not cover damage which has occurred during transport from the point of purchase to the consumer’s home. This warranty does not cover glass, light bulbs, batteries, transportation, labor, or other issues not associated with the manufacture of the product.
This product is for residential use only. Any and all commercial use of this product voids all warranties and absolves the manufacturer from all liability.
Read and understand all assembly and operating instructions, and all safety information and warnings, before use. The following will void this warranty: Damage caused by tampering, modifying, or altering the fireplace insert in any manner; Damage due to incorrect assembly, improper care, misuse, or abuse; Damage from being used with the wrong power source; Water damage; Damage caused from this insert being used outdoors; Damage caused by using for excessive periods of time; Damage caused by the insert being used in a commercial application; Damage from use as a primary heat source; Other misuse or abuse not specifically listed herein.
This product is not intended to be used as a primary heat source. It is for supplemental heating purposes only.
Model: Houselux 28Z,Houselux 30Z,Houselux 33Z,Houselux 33WZ
Power supply :120V-60Hz
Power consumption : 1500W
Protection class: I
Light bulb : LED

support@mystflame.com Or call us at 1-302-332-9680

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>