UNV 43Inch LED UHD Monitor User Guide

UNV 43Inch LED UHD Monitor

Safety guidelines

The installation and routine maintenance of the equipment must be operated by qualified and skilled staff. Before use, please read this instruction manual carefully and follow the safety guidelines.

• The device’s operating voltage is AC100-240V. Power of surveillance system must be provided by ups power or regulated power supply device. Nominal power of regulated power supply device must be 1.5 times greater than system power.
• Surveillance system must be in cophase power supply with image controller and controlling computer. Avoid cophase power supply with high power electrical devices, such as air conditioner.
• All grounding devices must be grounded reliably, such as decoder, video processor and matrix. Single point grounding shall be adopted, the ground wires of all device are connected to the equipotential bar. The ground wire should be multi-core coppei wire, shall not be short circuited or mixed with the null line of the power grid.
• Pls use the device in the environment of 5 to 40 degrees, otherwise device failures may be caused by temperature. The humidity should be 10% to 85%, Dehumidifier should be installed in high humidity environment.
• During wiring, the strong wire slot and the weak wire slot must be strictly separated do not cross. Try to short the routine distance. The connection between slots must be smooth without burrs and sharp corners. The slots must have good public grounding and good shielding.
• All Devices in the surveillance system must be grounded reliably. All grounding points must be connected to the same ground bar and ensure that the pressure difference between each equipment is zero.
• This is a class A product, may cause radio interference in the living environment. Users may be required to take actions against them.
• Keep the device far away from sources of water and fire, such as candles.
• High voltage inside, don’t open the cases of device.
• The LCD panel of device is fragile, pls handle it carefully, don’t press it heavily during the transportation and installation. Pls don’t knock, squeeze and scratch the LCD panel with a hard object.
• Pls don’t keep the device in standby mode fora long time. If you do not use the device fora long time, please unplug the power. Do not switch on and off the LCD monitor frequently, and the switching interval should not be less than 3 minutes.
• Please do not let any sharp object, metal or liquid touch the signal connector or cooling hole to avoid short circuit and product damage. It may cause electric shock, especially in the presence of children. 1

Packing content

Appearance introduction

Appearance of device

The manual contains a variety of models. The instruction is based on one model if not specified. The picture is just for your reference, pls subject to the real object.

to previous menu. Function of button is same with remote control.
SOURCE| Press °source° to enter the signal selection interface.
VOL +/ –| Press “VOL–“or °VOW to decrease the volume or increase the volume except OW menu operation. Function of “VOLIVOL4– button is same with remote control.

Comments: Different models, different appearance, pls subject to the real object. 2

Interface introduction

Introduction of some interfaces:

Cable Connection

HDMI cable instruction
When use 5M or above HDMI cable, High quality HMDI cable is required to get stable signal and display. Unqualified HDMI cable may cause noise or image instability. Both signal source and quality of HDMI cable will affect the display.

Comments: I’ The gold plating of the joint of cable falls off or becomes loose may lead to image noise after long term use.

Remote control

Remote controls for different modes may have difference, pls subject to the real object.

Troubleshooting

No Image on Screen.

• Check if the power button has been switched on.
• Verify the brightness and contrast of the monitor is within the normal setting.
• Check if the power indicator is flashing. If so this indicates that the monitor is not receiving the input signal.
• If the signal indicator is notebook or laptop, make sure that the signal has been switched to screen mode. Non-focus Image. Check if the image signal cable is inserted properly (upright position). Flash Screen.
• The power is insufficient to connect the monitor or too weak.
• To avoid magnetic field around the monitor, do not place these devices dose to it. Such as speakers, fluorescence lightings,AC transformer, table fan, and etc.
• By pressing the Exit key,the Auto Adjust Image function will automatically apply optimizes settings to the display. Wrong or Unusual Colour.
• If red, green, blue, or any of the colour disappears, check to see if the signal cord is connected properly.
• If the plug is loosely connected it might cause bad connection.
• Try connecting to another PC for comparison. The Whole Screen Appear Up and Down H-rolling Scan.
• Make sure that the input signal frequency is within 55-76Hz.
• Re-tighten the signal cable. How to Clean the Monitor.
• Make sure that the monitor power has been switched off.
• Do not spray any liquid on the screen orthe plastic panel directly. When Cleaning the Screen. Use clean, soft no fur materials to clean the screen. If it is still dirty, do add a little of non-ammonia liquid and non-alcohol glass cleanser to clean the screen. When Cleaning the Plastic Panel. Use soft dry cloth To add a little of non-ammonia liquid and non-alcohol of non-abrasion cleanser to clean surface if it is still unclean.

Manufacturer and Importer

You can See the outside packing box for manufacturer and importer information.

Disclaimer and Safety Warnings

Copyright Statement
C 2022 Zhejiang Uniview Technologies Co.,Ltd.All rights reserved No part of this manual may be copied, reproduced, translated or distributed in any form by any means without prior content in writing from Zhejiang Uniview Technologies Co., Ltd (referred to as Uniview or us hereafter). The product described in this manual may contain proprietary software owned by Uniview and its possible licensors. Unless permitted by Uniview and its licensors, no one is allowed to copy, distribute, modify, abstract, decompile, disassemble, decrypt, reverse engineer, rent, transfer, or sublicense the software in any form by any means.
Trademark Acknowledgements
are trademarks or registered trademarks of Uniview.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. All other trademarks, products, services and companies in this manual or the product described in this manual are the property of their respective owners. Export Compliance Statement
Unified complies with applicable export control laws and regulations worldwide , including that of the Peoples Republic of China and the United States, and abides by relevant regulations relating to the export, re-export and transfer of hardware, software and technology. Regarding the product described in this manual, Uniview asks you to fully understand and strictly abide by the applicable export laws and regulations worldwide.
EU Authorised Representative
UNV Technology EUROPE B.V. Room 2945,3rd Floor, Randstad 21-05 G, 1314 BDAlmere, Netherlands.
Privacy Protection Reminder
Uniview complies with appropriate privacy protection laws and is committed to protecting user privacy. You may want to read our full privacy policy at our website and get to know the ways we process your personal information. Please be aware, using the product described in this manual may involve the collection of personal information such as face, fingerprint, license plate number , email, phone number,GPS.Please abide by your local laws and regulations while using the product
About This Manual

• This manual is intended for multiple product models, and the photos, illustrations, descriptions, etc, in this manual may be different from the actual appearances, functions, features, etc, of the product.
• This manual is intended for multiple software versions, and the illustrations and descriptions in this manual may be different from the actual GUI and functions of the software.
• Despite our best efforts, technical or typographical errors may exist in this manual. Uniview cannot be held responsible for any such errors and reserves the right to change the manual without prior notice.
• Users are fully responsible for the damages and losses that arise due to improper operation.
• Uniview reserves the right to change any information in this manual without any prior notice or indication.Due to such reasons as product version upgrade or regulatory requirement of relevant regions, this manual will be periodically updated.

Disclaimer of Liability

• To the extent allowed by applicable law, in no event will Uniview be liable for any special, incidental, indirect, consequential damages, nor for any loss of profits, data, and documents.
• The product described in this manual is provided on an “as is” basis. Unless required by applicable law, this manual is only for informational purpose, and all statements, information, and recommendations in this manual are presented without warranty of any kind, expressed or implied, including, but not limited to, merchantability, satisfaction with quality, fitness fora particular purpose, and noninfringement.
• Users must assume total responsibility and all risks for connecting the product to the Internet, including, but not limited to, network attack, hacking, and virus. Uniview strongly recommends that users take all necessary measures to enhance the protection of network, device, data and personal information. Uniview disclaims any liability related thereto but will readily provide necessary security related support.
• To the extent not prohibited by applicable law, in no event will Uniview and its employees, licensors, subsidiary, affiliates be liable for results arising out of using or inability to use the product or service, including, not limited to, loss of profits and any other commercial damages or losses, loss of data, procurement of substitute goods or services; property damage, personal injury, business interruption, loss of business information, or any special, direct, indirect, incidental, consequential, pecuniary, coverage, exemplary, subsidiary losses, however caused and on any theory of liability, whether in contract, strict liability or tort (including negligence or otherwise) in any way out of the use of the product, even if Uniview has been advised of the possibility of such damages (other than as may be required by applicable law in cases involving personal injury, incidental or subsidiary damage).
• To the extent allowed by applicable law, in no event shall Uniview’s total liability to you for all damages for the product described in this manual (other than as may be required by applicable law in cases involving personal injury) exceed the amount of money that you have paid for the product.

Network Security
Please take all necessary measures to enhance network security for your device. The following are necessary measures for the network security of your device

• Change default password and set strong password: You are strongly recommended to change the default password after your first login and set a strong password of at least nine characters including all three elements: digits, letters and special characters.
• Keep firmware up to date: It is recommended that your device is always upgraded to the latest version for the latest functions and better security. Visit Uniview’s official website or contact yourlocal dealer for the latest firmware. The following are recommendations for enhancing network security of your device: • Change password regularly: Change your device password on a regular basis and keep the password safe.Make sure only the authorized user can log in to the device.
• Enable HTTPS/SSL: Use SSL certificate to encrypt HTTP communications and ensure data security.
• Enable IP address filtering: Allow access only from the specified IP addresses.
• Minimum port mapping: Configure your router or firewall to open a minimum set of ports to the WAN and keep only the necessary port mappings. Never set the device as the DMZ host or configure a full cone NAT
• Disable the automatic login and save password features: If multiple users have access to your computer, it is recommended that you disable these features to prevent unauthorized access.
• Chooseusemameand passworddiscretely: Avoid using the username and password of your social media, bank, email account, etc, as the username and password of your device, in case your social media, bank and email account information is leaked.
• Restrict user permissions: If more than one user needs access to your system, make sure each user is granted only the necessary permissions.
• Disable UPnP: When UPnP is enabled, the router will automatically map internal ports, and the system will automatically forward port data, which results in the risks of data leakage. Therefore, it is recommended to disable UPnP if HTTP and TCP port mapping have been enabled manually on your router. \
• SNMP: Disable SNMP if you do not use it. If you do use it, then SNMPv3 is recommended.
• Multicast: Multicast is intended to transmit video to multiple devices. If you do not use this function, it is recommended you disable multicast on your network.
• Check logs: Check your device logs regularly to detect unauthorized access or abnormal operations.
• Physical protection: Keep the device in a locked room or cabinet to prevent unauthorized physical access.
• Isolate video surveillance network: Isolating your video surveillance network with other service networks helps prevent unauthorized access to devices in your security system from other service networks. Learn More You may also obtain security information under Security Response Center at Uniview’s official website.

Safety Warnings

• The device must be installed, serviced and maintained by a trained professional with necessary safety knowledge and skills. Before you start using the device, please read through this guide carefully and make sure all applicable requirements are met to avoid danger and loss of property.
  Storage Transportation, and Use

• Store or use the device in a proper environment that meets environmental requirements, including and not limited to, temperature, humidity, dust, corrosive gases, electromagnetic radiation, etc.

• Make sure the device is securely installed or placed on a flat surface to prevent falling.

• Unless otherwise specified, do not stack devices.

• Ensure good ventilation in the operating environment. Do not cover the vents on the device. Allow adequate space for ventilation.

• Protect the device from liquid of any kind.

• Make sure the power supply provides a stable voltage that meets the power requirements of the device. Make sure the power supply’s output power exceeds the total maximum power of all the connected devices.

• Verify that the device is properly installed before connecting it to power. ]

• Do not remove the seal from the device body without consulting Unified first. Do not attempt to service the product yourself. Contact a trained professional for maintenance.

• Always disconnect the device from power before attempting to move the device.

• Take proper waterproof measures in accordance with requirements before using the device outdoors.
  Power Requirements

• Installation and use of the device must be in strict accordance with your local electrical safety regulations.

• Use a UL certified power supply that meets LPS requirements if an adapter is used.

• Use the recommended cordset (power cord) in accordance with the specified ratings.

• Only use the power adapter supplied with your device

• Use a mains socket outlet with a protective earthing (grounding) connection. ‘

• Ground your device properly if the device is intended to be grounded.
  Battery Use Caution

• When battery is used, avoid:

  • High or low extreme temperatures during use, storage and transportation;
  • Extremely low air pressure, or low air pressure at high altitude.

• Use the battery properly. improper use of the battery such as the following may cause risks of fire, explosion or leakage of flammable liquid or gas.

  • Replace battery with an incorrect type;
  • Dispose of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery;

• Dispose the used battery according to your local regulations or the battery manufacturer’s instructions

Regulatory Compliance

FCC Statements
This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Compliance Information Statement refer to: http://en.uniview.com/Support/Download_Center/Product_Installation/Declaration/
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates,uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
LVD/EMC Directive
This product complies with the European Low Voltage Directive 2014/35/EU and EMC Directive 2014/30/EU.
** WE EE Directive-2012/19/EU
The product this manual refers to is covered by the Waste Electrical & Electronic Equipment (WEEE) Directive and must be disposed of in a responsible manner.
Battery Directive-2013/56/EC
**Battery in the product complies with the European Battery Directive 2013/56/EC. For proper recycling, return the battery to your supplier or to a designated collection point.

Documents / Resources

| UNV 43Inch LED UHD Monitor [pdf] User Guide
43Inch LED UHD Monitor, 43Inch Monitor, LED UHD Monitor, Monitor, LED Monitor, UHD Monitor
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>