UNV Display MW3232-V-K2 Surveillance Monitor User Guide

: September 19, 2024
: UNV Display

Table of Contents

UNV Display MW3232-V-K2 Surveillance Monitor
Packing List
Button Instruction
Interface
Power Light
MENU
Troubleshooting
Disclaimer and Safety Warnings
Regulatory Compliance
Read User Manual Online (PDF format)
Download This Manual (PDF format)

UNV Display MW3232-V-K2 Surveillance Monitor

Packing List

Please check the items in your package carefully. Contact your dealer if anything is missing or damaged.

No.	Name	Unit
1	Monitor (base attached )	PCS
2	HDMI Cable	SET
3	Quick Guide	SET
4	Adapter	SET

Button Instruction

MENU	Show main choice menus
LEFT	Adjust the option-move up or lower/Hotkey(option)
RIGHT	Adjust the option-move down or higher/Hotkey(option)

EXIT

| Power on or off

Exit main menu,or when no menus-auto adjust

Interface

Power Light

Green (blue): turn on the machine
Green (blue): normal working condition
Orange: standby

The LCD monitor display unit has been adjusted to the best condition before shipment. You can also follow the instructions and steps below to adjust the image.

| BRIGHTNESS| 0-100                   Backlig ht Adjustment
---|---|---
CONTRAST| 0-100                   Contrast from Digital -register
ECO| STANDARD     Standard Mode
FPS               FPS Mode
RTS               RTS Mode
GAME            Game Mode
MOVIE            Movie Mode
| OFF             Disable dynamic contrast ratio
OCR

ON Enable dynamic contrast ratio

| H.POSITION 0-100|

Adjust the vertical/ horizontal position of the picture

V.POSITION 0-100
CLOCK 0-100 Adjust pict ure Clock to reduce

Vertical -Line noise

PHASE 0-100| Adjust pict ure Phase to reduce Horizontal -Line noise

ASPECT WIDE OR 4:3

| Select wide or 4:3 format for display

|

COLOR TEMP.

| USER, WARM, NORMAL, COOL, sRGB
---|---|---

USER

| RED| 0-100
GREEN| 0-100
BLUE| 0-100
LOW BLUE

LIGHT

| OFF| WEAK, MEDIUM, STRONG, OFF

Current operation will increase product energy consumption.

Do you want to continue?
Yes No

Troubleshooting

No Image on Screen.

Check if the power button has been switched on.
Verify the brightness and contrast of the monitor is within the normal setting.
Check if the power indicator is flashing. If so this indicates that the monitor is not receiving the input signal.
If the signal indicator is notebook or laptop, make sure that the signal has been switched to screen mode.

Non-focus Image.
Check if the image signal cable is inserted properly (upright position).

Flash Screen.

The power is insufficient to connect the monitor or too weak.
To avoid magnetic field around the monitor, do not place these devices close to it. Such as speakers, fluorescence lightings, AC transformer, table fan, and etc.
By pressing the Exit key, the Auto Adjust Image function will automatically apply optimizes settings to the display.

Wrong or Unusual Colour.

If red, green, blue, or any of the colour disappears, check to see if the signal cord is connected properly.
If the plug is loosely connected it might cause bad connection.
Try connecting to another PC for comparison.

The Whole Screen Appear Up and Down H-rolling Scan.

Make sure that the input signal frequency is within 55-76Hz.
Re-tighten the signal cable.

How to Clean the Monitor.

Make sure that the monitor power has been switched off.
Do not spray any liquid on the screen or the plastic panel directly.

When Cleaning the Screen.

Use clean, soft no fur materials to clean the screen.
If it is still dirty, do add a little of non-ammonia liquid and non-alcohol glass cleanser to clean the screen.

When Cleaning the Plastic Panel.

Use soft dry cloth.
To add a little of non-ammonia liquid and non-alcohol of non-abrasion cleanser to clean surface if it is still unclean.

Manufacturer and Importer
You can see the outside packing box for manufacturer and importer information.

Disclaimer and Safety Warnings

Copyright Statement

© 2024 Zhejiang Uniview Technologies Co., Ltd. All rights resenved.
No part of this manual may be copied, reproduced, translated or distributed in any form by any means without prior content in writing from Zhejiang Uniview Technologies Co., Ltd (referred to as Uniview or us hereafter).
The product described in this manual may contain proprietary software owned by Uniview and its possible licensors. Unless permitted by Uniview and its licensors, no one is allowed to copy, distribute, modify, abstract, decompile, disassemble, decrypt, reverse engineer, rent, transfer, or sublicense the software in any form by any means.

Trademark Acknowledgements

uniarch are trademarks or registered trademarks of Uniview.

The terms HDMl,HDMI H1. gh – De1 i· nI. tI. on Mu 1 ti· med ., a lnter 1a ce,HDMITrade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
All other trademarks, products, services and companies in this manual or the product described in this manual are the property of their respective owners.

Export Compliance Statement
Uniview complies with applicable export control laws and regulations worldwide, including that of the People’s Republic of China and the United States, and abides by relevant regulations relating to the export, re-export and transfer of hardware, software and technology. Regarding the product described in this manual, Uniview asks you to fully understand and strictly abide by the applicable export laws and regulations worldwide.

EU Authorised Representative
UNV Technology EUROPE B.V. Room 2945, 3rd Floor, Randstad 21-05 G, 1314 BD, Almere, Netherlands.

Privacy Protection Reminder
Uniview complies with appropriate privacy protection laws and is committed to protecting user privacy. You may want to read our full privacy policy at our website and get to know the ways we process your personal information. Please be aware, using the product described in this manual may involve the collection of personal information such as face, fingerprint, license plate number, email, phone number, GPS. Please abide by your local laws and regulations while using the product.

AboutThis Manual

This manual is intended for multiple product models, and the photos, illustrations, descriptions, etc, in this manual may be different from the actual appearances, functions, features, etc, of the product.
This manual is intended for multiple software versions, and the illustrations and descriptions in this manual may be different from the actual GUI and functions of the software.
Despite our best efforts, technical or typographical errors may exist in this manual. Uniview cannot be held responsible for any such errors and reserves the right to change the manual without prior notice.
Users are fully responsible for the damages and losses that arise due to improper operation.
Uniview reserves the right to change any information in this manual without any prior notice or indication. Due to such reasons as product version upgrade or regulatory requirement of relevant regions, this manual will be periodically updated.

Disclaimer of Liability

To the extent allowed by applicable law, in no event will Uniview be liable for any special, incidental, indirect, consequential damages, nor for any loss of profits, data, and documents.
The product described in this manual is provided on an “as is” basis. Unless required by applicable law, this manual is only for informational purpose, and all statements, information, and recommendations in this manual are presented without warranty of any kind, expressed or implied, including, but not limited to, merchantability, satisfaction with quality, fitness for a particular purpose, and non infringement.
Users must assume total responsibility and all risks for connecting the product to the Internet, including, but not limited to, network attack, hacking, and virus. Uniview strongly recommends that users take all necessary measures to enhance the protection of network, device, data and personal information. Uniview disclaims any liability related thereto but will readily provide necessary security related support.
To the extent not prohibited by applicable law, in no event will Uniview and its employees, licensors, subsidiary, affiliates be liable for results arising out of using or inability to use the product or service, including, not limited to, loss of profits and any other commercial damages or losses, loss of data, procurement of substitute goods or services; property damage, personal injury, business interruption, loss of business information, or any special, direct, indirect, incidental, consequential, pecuniary, coverage, exemplary, subsidiary losses, however caused and on any theory of liability, whether in contract, strict liability or tort (including negligence or otherwise) in any way out of the use of the product, even if Uniview has been advised of the possibility of such damages (other than as may be required by applicable law in cases involving personal injury, incidental or subsidiary damage).
To the extent allowed by applicable law, in no event shall Uniview’s total liability to you for all damages for the product described in this manual (other than as may be required by applicable law in cases involving personal injury) exceed the amount of money that you have paid for the product.

Network Security

Please take all necessary measures to enhance network securityfor your device. The following are necessary measures for the network security of your device:

Change default password and set strong password: You are strongly recommended to change the default password after your first login and set a strong password of at least nine characters including all three elements: digits, letters and special characters.
Keep firmware up to date: It is recommended that your device is always upgraded to the latest version for the latest functions and better security. Visit Uniview’s official website or contact your local dealer for the latest firmware.

The following are recommendations for enhancing network security of your device:

Change password regularly: Change your device password on a regular basis and keep the password safe. Make sure only the authorized user can log in to the device.
Enable HTTPS/SSL: Use SSL certificate to encrypt HTTP communications and ensure data security.
Enable IP address filtering: Allow access only from the specified IP addresses.
Minimum port mapping: Configure your router or firewall to open a minimum set of ports to the WAN and keep only the necessary port mappings. Never set the device as the DMZ host or configure a full cone NAT.
Disable the automatic login and save password features: If multiple users have access to your computer, it is recommended that you disable these features to prevent unauthorized access.
Choose username and password discretely: Avoid using the username and password of your social media, bank, ernail account, etc, as the username and password of your device, in case your social rnedia, bank and email account information is leaked.
Restrict user permissions: If rnore than one user needs access to your system, make sure each user is granted only the necessary permissions.
Disable UPnP: When UPnP is enabled, the router will automatically rnap internal ports, and the system will automatically forward port data, which results in the risks of data leakage. Therefore, it is recommended to disable UPnP if HTTP and TCP port mapping have been enabled manually on your router.
SNMP: Disable SNMP if you do not use it. If you do use it, then SNMPv3 is recommended.
Multicast: Multicast is intended to transmit video to multiple devices. If you do not use this function, it is recommended you disable multicast on your network.
Check logs: Check your device logs regularly to detect unauthorized access or abnormal operations.
Physical protection: Keep the device in a locked room or cabinet to prevent unauthorized physical access.
Isolate video surveillance network: Isolating your video surveillance network with other service networks helps prevent unauthorized access to devices in your security system from other service networks.

Learn More
You may also obtain security information under Security Response Center at Uniview’s official website.

Safety Warnings

The device must be installed, serviced and maintained by a trained professional with necessary safety knowledge and skills. Before you start using the device, please read through this guide carefully and make sure all applicable requirements are met to avoid danger and loss of property.

Storage, Transportation, and Use

Store or use the device in a proper environment that meets environmental requirements, including and not limited to, temperature, humidity, dust, corrosive gases, electromagnetic radiation, etc.
Make sure the device is securely installed or placed on a flat surface to prevent falling.
Unless otherwise specified, do not stack devices.
Ensure good ventilation in the operating environment. Do not cover the vents on the device. Allow adequate space for ventilation.
Protect the device from liquid of any kind.
Make sure the power supply provides a stable voltage that meets the power requirements of the device. Make sure the power supply’s output power exceeds the total maximum power of all the connected devices.
Verify that the device is properly installed before connecting it to power.
Do not remove the seal from the device body without consulting Uniview first. Do not attempt to service the product yourself. Contact a trained professional for maintenance.
Always disconnect the device from power before attempting to move the device.
Take proper waterproof measures in accordance with requirements before using the device outdoors.

Power Requirements

Installation and use of the device must be in strict accordance with your local electrical safety regulations.
Use an IEC certified power supply that meets LPS requirements if an adapter is used.
Use the recommended cordset (power cord) in accordance with the specified ratings.
Only use the power adapter supplied with your device.
Use a mains socket outlet with a protective earthing (grounding) connection.
Ground your device properly if the device is intended to be grounded.

Battery Use Caution

When battery is used, avoid:
- High or low extreme temperatures during use, storage and transportation;
- Extremely low air pressure, or low air pressure at high altitude.
Use the battery properly.Improper use of the battery such as the following may cause risks of fire, explosion or leakage of flammable liquid or gas.
- Replace battery with an incorrect type;
- Dispose of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery;
Dispose the used battery according to your local regulations or the battery manufacturer’s instructions

Regulatory Compliance

FCC Statements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Compliance Information Statement refer to:

http://en.uniview.com/Support/Download__Center/Product_Installation/Declaration/

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interterence to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

LVD/EMC Directive
This product complies with the European Low Voltage Directive 2014/35/EU and EMC Directive 2014/30/EU.

WEEE Directive-2012/19/EU
The product this manual refers to is covered by the Waste Electrical & Electronic Equipment (WEEE) Directive and must be disposed of in a responsible manner.

Battery Directive-(EU)2023/1542
Battery in the product complies with the European Battery Directive
2023/1542 EU. For proper recycling, return the battery to your supplier or to a designated collection point.

Raccolta Carta