NOVO 60-7543 Satco Exhibit 1 Light 14 inch Matte Black Outdoor Wall Sconce Instruction Manual
- June 3, 2024
- NOVO
Table of Contents
60-7543 Satco Exhibit 1 Light 14 inch Matte Black Outdoor Wall Sconce
Instruction Manual
INSTALLATION AND SAFETY INSTRUCTIONS
60-7543 Satco Exhibit 1 Light 14 inch Matte Black Outdoor Wall Sconce
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF;
EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Under no circumstances should a fixture be hung on
house electrical wires, nor should a swag type fixture be installed on a
ceiling which contains a radiant type heating system. Read instructions
carefully. If you are unclear as to how to proceed, consult a qualified
electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.
FIXTURE ASSEMBLY
Carefully remove the fixture from the carton and check that all parts are included as shown in figure. Be careful not to misplace any of the screws or parts, which are needed to install this fixture.
INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box.
STEP 1: Fasten the cross bar onto the outlet box by using the two outlet
box screws (included).
STEP 2: Tie ground wire from outlet box and from fixture to the ground
screw on the cross bar. Connect white wire from fixture to white wire (neutral
wire) from supply circuit. Connect black wire from fixture to black wire (live
wire) from supply circuit. Cover connections using provided wire connectors.
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your fixture.
Identify which group your fixture wire(s) falls into and connect the wires
according to the directions below:
GROUP A:
Connect to Black House Wire| GROUP B:
Connect to White House Wire
---|---
BLACK| WHITE
PARALLEL WIRE (round & smooth)| PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER| WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK WITHOUT TRACER| BROWN, GOLD OR BLACK WITH TRACER
NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is
square shaped or ridged and the less tracer wire is round in shape or smooth
(seen best when viewed from wire end.)
STEP 3: Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. Do NOT twist wires together before using
wire connectors.
STEP 4: Fit a wire connector over the wires and screw the connector
clockwise until you feel firmness.
Line art shown may not exactly match the fixture enclosed. However, the
installations do apply to this fixture.
STEP 5: Try gently to pull the connector off the wires. If you can pull
the connector off, carefully re-do steps 3 and 4 as above, and check again for
a firm connection.
STEP 6: Connect the fixture wire from group B to the white wire from the
outlet box in the same manner. Make sure no bare wires can be seen outside
wire connectors.
FINAL ASSEMBLY
STEP 1: Secure the back plate to the wall outlet box using the ball nuts.
STEP 2: Install lamp (not included). Do not exceed the maximum capacity
recommended on the socket.
STEP 3: Put the glass over the fixture, secure with the clips.
STEP 4: Secure the fixture to the back plate using the mounting screws.
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not
use abrasive materials such as scouring pads or powders, steel wool or
abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order replacement parts. Be sure to use exact wording from illustration when ordering parts.
ITEM NO: 60-7543
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>