Novo Water 485UF 485 High Efficiency Softeners User Manual

: October 30, 2023
: Novo Water

Novo Water 485UF 485 High-Efficiency Softeners

Novo Water 485UF 485 High Efficiency Softeners

Product Information

The Canature WaterGroup Softener is a water treatment system designed for upflow and downflow installations. The system comes with an automatic resin cleaner solution feeder (optional), which helps to maintain the softener’s performance and prolongs its lifespan. The system is not meant for treating water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

Feed Water Parameters

The maximum iron concentration should be 2.0 ppm ferrous (clear water iron), and the maximum hydrogen sulfide should be 0.0 ppm. The maximum manganese concentration should be 0.75 ppm ferrous (clear water). The pH level should range between 6.5 to 8.5 with no iron or manganese present, and between 6.5 to 7.5 with iron or manganese present.

FEED WATER PARAMETERS
Maximum Iron** = 2.0 ppm ferrous (clear water iron)
Maximum Hydrogen Sulfide = 0.0 ppm
Maximum Manganese = 0.75 ppm ferrous (clear water)
pH = 6.5 to 8.5 with no iron or manganese present
pH = 6.5 to 7.5 with iron or manganese present
See System Maintenance Section – Resin Cleaner

Product Usage Instructions

Before installation, apply IAPMO-certified lubricant to all seals to avoid pinched o-rings during installation.
To ensure optimal performance, users should adhere to the feed water parameters mentioned in the user manual. The Canature WaterGroup Softener is not intended for treating water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.
If the system fails to regenerate automatically, users should verify the programming and correct the hardness level and amount o people in the home if necessary. Users should also check for low salt levels and fill salt to above the water level in the salt tank. If the injectors or injector screens are plugged, users should clean and/or replace them according to the maintenance instructions. If necessary, users can clean the resin using an approved resin
cleaner obtained from an authorized dealer or local plumbing supply store. For permanent maintenance, users can add an automatic resin cleaner solution feeder to the system.

AUTOMATIC RESIN CLEANER SOLUTION FEEDER INSTALLATION INSTRUCTIONS

(OPTIONAL)

Resin Cleaner
An approved resin cleaner MUST be used on a regular basis if your water supply contains iron. The amount of resin cleaner and frequency of use is determined by the quantity of iron in your water (consult your local representative or follow the directions on the resin cleaner package).
Res-Up Feeders attach to your brine tank and automatically dispense the Res-Up cleaner into the brine solution where it cleans the resin during the regeneration cycle.
The feeder hooks onto the tube inside your brine tank and you just pour some chemical in it and your water conditioner should last significantly longer. A res-up feeder is essential if your raw water contains measurable amounts of iron.

Res-Up Feeder Bottle (Chemical sold Separately)

The 12 cc feeder (Part # 33010) is for conditioners up to 64,000 grains (2 ft3 of resin).
The 30 cc feeder (Part # 33018) is for larger conditioners over 64,000 grains.
Pro-Res Care Chemicals
Item #45147 Pro-ResCare – Gallon
Item #45148 Pro-ResCare – Quart

Install Res-Up Feeder

Install the grid and brine well inside the tank.
Measure 2 inches from the top of the tank beside the oblong molding.
Mark the location of the holder and drill.
IInstall the holder and the Res Care Solution
Take off the small hole cover on the Brine Well lid.
Take off the cover of the Res Care bottle. Insert the wick, making sure it touches the bottom of the bottle. Insert the other end of the tube completely into the hole in the brine well cap. Automatic feeding will start in a few hours.

PROBLEM WATER INJECTOR KIT

For use on upflow softeners only.
IMPORTANT!: If the water source this water softener is being applied on is not municipal water and contains up to 2.0 mg/l/ppm of ferrous (Clear Water) iron and/or up to .75 mg/l/ppm of manganese, the enclosed Problem Water Injector Kit needs to be installed into the control valve following these instructions.
FAILURE TO DO THIS WILL RESULT IN UNSATISFACTORY OPERATION OF THIS EQUIPMENT AND VOID ANY IMPLIED PERFORMANCE WARRANTY. Novo Water 485UF 485 High
Efficiency Softeners fig-4

Replace injectors with correct number and color corresponding to your equipment size. *NOTE: Remember to properly lubricate ALL O-Rings with the silicone lubricant supplied.

CLEAN INJECTOR ASSEMBLY – FOR MODELS BEFORE JUNE, 2022
Sediment, salt, and silt will restrict or clog the injector. A clean water supply and pure salt will prevent this from happening. The injector assembly is located on the right side of the control valve when facing your softener.

The assembly is easy to clean, start by:

Shut the water supply to your softener OFF.
Reduce the pressure by opening a cold-treated tap.
Using a screwdriver, remove the four (4) screws holding the injector cover to the control valve body.
Carefully, remove the cover, and disassemble as shown below.
The injector orifice is removed from the valve body by carefully turning it out with a screwdriver.
Remove the injector throat the same way.
Carefully flush all parts including the screen.
Use a mild acid such as vinegar or Pro Rust Out to clean the small holes in the orifice and throat.
Reassemble by reversing the procedure.

Remove the four (4) screws of the injector cap. Pull the Injector Cap out.
Remove the Injector Assembly, O-ring, and screen.
Clean the injectors and replace the cap.
Be sure to replace the O-rings when reassembling and lubricate with approved 100% silicone-based lubricant. Order Part #92360.
During final assembly be sure the injector is seatedcorrectly as shown in figure above.

CLEAN INJECTOR ASSEMBLY – FOR MODELS AFTER JUNE, 2022
Sediment, salt, and silt will restrict or clog the injector. A clean water supply and pure salt will prevent this from happening. The injector assembly is located on the right side of the control valve when facing your softener.

The assembly is easy to clean, start by:

Shut the water supply to your softener OFF.
Reduce the pressure by opening a cold-treated tap.
Using a screwdriver, remove the four (4) screws holding the injector cover to the control valve body.
Carefully, remove the cover, and disassemble as shown below.
The injector orifice is removed from the valve body by carefully turning it out with a screwdriver.
Remove the injector throat the same way.
Carefully flush all parts including the screen.
Use a mild acid such as vinegar or Pro Rust Out to clean the small holes in the orifice and throat.
Reassemble by reversing the procedure.

Remove the three (3) screws of the injector cap.
Pull the Injector Cap out.
Remove the Injector Assembly, O-ring, and screen.
Clean the injectors and replace the cap.
Be sure to replace the O-rings when reassembling and lubricate with approved 100% silicone-based lubricant. Order Part #92360.
During final assembly be sure the injector is seated correctly as shown in figure above.

Troubleshooting Guide

The troubleshooting guide provides solutions to common problems that users may encounter with the Canature WaterGroup Softener system. These include untreated water delivery, excessive water in the salt tank, failure to regenerate automatically, failure to use salt, discolored water, and excessive pressure loss. Users are advised to test their water before attempting any troubleshooting and refer to the maintenance section for injector cleaning, salt tank cleaning, and resin cleaning.

Problem	Possible Solutions

LEVEL 1 — SEE HOMEOWNERS MANUAL

Recommended for the homeowner

| IMPORTANT

before attempting any troubleshooting be sure to test the water or have the water tested.

The tests should include the raw water, the hot treated water, and the cold treated water.

Delivers untreated water

| Bypass is closed bypassing raw water past the unit – Return bypass valve to the open position to service the home – See ‘Manual Water Bypass’
Bypass loop in the home’s plumbing – Close outlet valve only on conditioner bypass, open nearest conditioned water line. If no water flow then there is not a bypass in the plumbing. If there is water flow then there is a hidden bypass in the plumbing (contact plumber).
No salt or low salt level – Fill salt to above the water level in the salt tank. Low salt will affect the conditioners capacity. – See ‘Maintenance’
Not programmed correctly for current application – Verify programming. Correct hardness level and amount of people in the home if necessary. – See ‘Start Up and Programming’
Excessive water in the salt tank| Refer to Maintenance, Cleaning the Injectors and Cleaning the Salt Tank

Not regenerating automatically, not metering water flow

| Check diagnostics for last regeneration – See How Your Conditioner Works

Open nearest conditioned water outlet and check if gallons is counting down, if not metering –

Contact authorized service representative

Not using salt| Injectors or injector screen plugged. Clean and or replace injectors and screen – See ‘Maintenance’

Salt Bridged in salt tank – See ‘Maintenance’

Not regenerating automatically – Alarms| Caused by a power outage or brown out during regeneration – unplug power for 30 seconds then

re-connect. If alarm continues – Contact your authorized service representative, if necessary.

Unit regenerates but does not use salt

| Clean and or replace injectors – See ‘Maintenance’
Drain line flow control is plugged – clean drain line flow control to ensure there are no kinks, or restrictions in the drain line.
Using too much salt or more salt than expected| Check programming – is the unit set properly for salt efficiency, is the programming correct for hardness and people – See ‘Start Up and Programming

Alarms after regeneration

| Caused by a power outage or brown out during regeneration – unplug power for 30 seconds then reconnect if alarm continues – Contact your authorized service representative, if necessary.
Corroded or damaged rear circuit – replace circuit Contact your authorized service representative, if necessary.
4 D iscolor ed water| Result of city / town supply being contaminated – check with local authority to see if there has been water main activity in your area. If there has been, manually regenerate the unit a couple of times in a row to clear the color. If there hasn’t been, Contact your authorized service representative if necessary.
Iron Bleed through – if there are small amounts of iron in your raw water supply eventually it will build up in the resin and could result in bleed through.

– review settings to compensate for iron in the water – See ‘Start Up and Programming’

– Contact your dealer or local plumbing supply store to obtain an approved resin cleaner. Use resin cleaner to clean the resin as directed. For permanent maintenance if required add in an automatic feeder – See Automatic Resin Cleaner Solution Feeder

Excessive pressure loss| Check unit specifications – peak or continuous service flow rates maybe exceeding capacity causing the unit to be restrictive due to size – See ‘Unit Specifications’ – Contact your dealer if necessary.
Problem| Possible Solutions
---|---
LEVEL 2 –

recommended for qualified service technician only

|

Not drawing brine solution

| Injectors or injector screen plugged. Clean and or replace injectors and screen – See Replacement/ Service Section

Drain line flow control plugged or drain line restricted – See Replacement/Service Section Safety float assembly seating prematurely – clean or replace safety float and clean brine tank – See Parts Section

Loose connections between control valve and safety float allowing unit to draw air – See Replacement/Service Section

No water in salt tank

| Loose connections between control valve and safety float allowing unit to draw air –

See Replacement/Service Section

Refill time not set correctly for unit size; water not coming above the grid plate.

Refill control button plugged causing no refill – clean and or replace refill control button.

Check size of BLFC noted on silver label of valve and be sure valve is programmed to correspond to the correct size used.

Problem| Possible Solutions

** Not regenerating automatically Alarms **

| Jammed piston – replace piston and seal assembly – See Replacement/Service Section Defective or damaged circuit – replace circuit See Replacement/Service Section

Loose or corroded connections between the 2 circuits – reconnect securely or replace – See Replacement/Service Section

Drive motor defective replace motor – See Replacement/Service Section

Conditioner initiates regeneration but alarms after a few seconds| Drive motor defective replace motor – See Replacement/Service Section Defective transformer replace transformer.
Internal valve leak – Running to the drain constantly| Replace piston and seal assemblies – See Replacement/Service Section
Not drawing brine no problem with injectors or drain| Replace piston and seal assemblies – See Replacement/Service Section

**Meter not counting down **

| Check diagnostics for last regeneration .

Check that meter cable is plugged into the meter assembly – See Replacement/Service Section Check that meter cable is reading the meter by moving a fridge magnet (or similar magnet) across it rapidly for a few seconds you should be able to see the gallons change.

Be sure there is no debris caught in the the turbine

If the meter cable is good, and no debris caught then replace the meter assembly – See Replacement/Service Section

Leaking past distributor tube| Contact Technical Services for additional troubleshooting information: 877-288-9888

Alarms after regeneration or after manual regeneration

| Damaged or missing sensor magnet on brine gear – replace as required, or send in for repair to nearest office.

Corroded or damaged rear circuit – replace as required.

Excessive pressure loss

| Check unit specifications – peak or continuous service flow rates may be exceeding capacity caus- ing the unit to be restrictive due to size – See product-specific information on warranty sheets

suplied with the unit. Contact Customer Service for clarification if this is suspected – 877-288-9888.

Upper distributor cone plugged with foreign material – remove valve, remove upper distributor cone and clean then replace and put valve back on unit.
Chlorine degradation of resin – excessive amounts of chlorine or chloramine can damage soften- ing resin and break it down causing excessive pressure loss – replace media bed and add in a chlorine removal system to protect the softener.

REPLACEMENT/SERVICE

THE FOLLOWING ‘REPLACEMENT / SERVICE SECTION’, PAGES 9 TO 13 CONTAIN CONTENT THAT SHOULD ONLY BE USED BY A QUALIFIED SERVICE TECHNICIAN:

TIMER REMOVAL

Remove screw & washer from piston rod link
Remove 2 bolts securing powerhead to body
Remove powerhead from body

INSPECTION AND REPLACEMENT OF PISTON ASSEMBLY AND SEAL AND SPACER KIT

Novo Water 485UF 485 High Efficiency Softeners fig-10

Follow steps 1 to 3 of Timer Removal above.
Remove three screws from the plate on the valve body.
Remove the plate from the valve body and pull the Piston Assembly from the valve. The brine valve assembly can also be removed in this stage.
Remove the seal spacer assembly, grease it with silicone lubricant (# 92360).
Re-install in this order: seal and spacer assembly, piston assemby, brine valve assembly, and then the timer assembly.

BYPASS AND METER CABLE REPLACEMENT

If valve is manufactured before March 20th, 2018, and customer wishes to replace or service impeller on bypass. Customer can order item #60010238. If customer wishes to replace to new design, then follow the steps below. Novo
Water 485UF 485 High Efficiency Softeners fig-11

Novo Water 485UF 485 High Efficiency Softeners fig-12

Valve Model	Region	Meter Ratio
OLD	NEW
85UF Series	U.S Gallon	8.000

METER ASSEMBLY REPLACEMENT

Novo Water 485UF 485 High Efficiency Softeners fig-13

Disconnect the meter cable from the meter.
Disconnect the valve from bypass by removing clips
Remove the coupling adapter from the bypass

MOTOR REPLACEMENT

Novo Water 485UF 485 High Efficiency Softeners fig-14

Remove the powerhead cover and disconnect the LCD cable from the circuit board
Remove the motor screws
Pull the motor out from powerhead

CLEAN INJECTOR ASSEMBLY

Novo Water 485UF 485 High Efficiency Softeners fig-15

Remove four screws of the injector cap.
Pull the Injector Cap Out
Remove the injector assembly, oring and screen,
Clean the injectors then replace screen (if necessary) and re-install end cap assembly and screws

DRAIN LINE FLOW CONTROL REPLACEMENT

Novo Water 485UF 485 High Efficiency Softeners fig-16

Pull the drain line clip and remove the drain line elbow and washer
Clean/replace drain line washer

BRINE LINE FLOW CONTROL REPLACEMENT

PCB REPLACEMENT Novo Water 485UF 485 High Efficiency Softeners
fig-18

DISPLAY REPLACEMENT

Novo Water 485UF 485 High Efficiency Softeners fig-19

AFTER SERVICING

Reconnect drain line
Return bypass or inlet valve to normal in service position. Water pressure will automatically build in the conditioner.
Check for leaks at all sealed areas. Check drain seal with the control in the backwash position.
Plug electrical cord into outlet
Set ‘Time of Day ‘and cycle the control valve manually to ensure proper function. Make sure control valve is returned to the ‘In Service’ position.

PARTS BREAKDOWN

Novo Water 485UF 485 High Efficiency Softeners fig-20

Model| Mineral Tank Size| Tank #| Distributor#| Upper Cone #| Valve #| Media Bed #| Brine Tank
---|---|---|---|---|---|---|---
75| 8 x 44| 25020051| 50010019|

18280

|

10010060

(Upflow Valve)

10010062

(Downflow Valve)

| 95600| 30020006
100| 9 x 48| 25020052| 50010006| 95601| 30020006
150| 10 x 54| 25020053| 50010005| 95606| 30020006
200| 12 x 52| 25010058| 50010005| 95609| 30020010
300| 14 x 65| 25030001 and 50040039| 50010010| 95604| 30020032
75C| 9 x 35| 25010028| 50010020| 95600| N/A
100C| 10 x 35| 25010043| 50010020| 95601| N/A

Novo Water 485UF 485 High Efficiency Softeners fig-21

Powerhead parts list

Novo Water 485UF 485 High Efficiency Softeners fig-22

No.	Part #	Description	Qty
23	60010331	Power Cable Clip	1
22	60010330	Meter Cable Clip	1
21	60010124	Power Cable	1
20	60010240	Display-PCB cable	1
19	60010267	Meter Cable, Grey	1
18	80080164	485HE Face Label	1
17	60095662	Bnt485 Display Plate(White)	1
16	60010309	Bnt485 Housing(White)	1
15	60021979	Bnt85HE Display (After Aug.15, 2019)	1
14	92393	Bnt85 Motor	1
13	60095658	Motor Pin	1
12	60010673	Screw-ST2.9×10	8
11	60021982	Main Pcb, (DF) (After Aug. 15, 2019)
60021981	Main Pcb, (UF) (After Aug. 15, 2019)
10	60010574	Screw-ST3.5×13	10
9	60010573	Bnt85HE Mounting Plate	1
8	60010575	Screw-4.2×12	1
4	60095102	Gear, Brine, 85UF	1
60095103	Gear, Brine, 85DF
3	92391	Main Gear, 85HE	1
2	92389	Bnt85 Drive Gear	1
1	60095077	Bnt485 Base(White)	1
	60010371	Complete Powerhead,485UF
	60010372	Complete Powerhead,485DF
	60010052	Transformer, 12V

85 Valve Body Parts List (After June 2022)

No.	Part #	Description	QTY
1	60010099	Screw 2.9×13	2
2	60010599	Valve Bottom Connector	1
3	60010080	O-Ring 25×3.55	1
4	60010598	Adaptor Central Pipe	1
5	60010597	O-Ring 34.5×1.8	1
6	60010077	O-Ring 78.74×5.33	1
7	60010069	Secure Clips	2
8	optional sizes	Drain Line Flow Washer	1
9	60010044	O-Ring 12×2	2
10	60090001	Drain Fitting	1
11	60010409	Seals and Spacers kit	1
12	60010129	Upflow Piston Assembly	1
60010171	Downflow Piston Assembly
13	60010645	End Plug Retainer	1
14	60010075	Screw 5×12	3
15	60010417	Brine Valve	1
16	60090004	Brine Line Elbow	1
17	60010184	Nut 3/8 BLFC	1
18	60010188	O-Ring BLFC Holder	1
19	optional sizes	Brine Line Flow Washer	1
20	60010293	Brine Line Flow Washer Holder	1
21	60010419	Screw 5×20	3
22	optional sizes	Injectors	1
23	60010413	Injector Holder	1
24	60010418	Quad Ring Seal	1
25	60010416	Check Ball (Downflow Valve Only)	1
26	60010410	Retainer	1
27	60010411	Injector Cover	1
28	60010414	Gasget Injector Cover	1
29	60010415	Injector Screen	1
30	60010412	Injector Holder Plugged	1
31	60010338	O-Ring 12.42×1.78	2
32	60010186	O-Ring 12.5×1.5	2

Novo Water 485UF 485 High Efficiency Softeners fig-25

85 Valve Body Parts List (Before June 2022)

No.	Part #	Description	Qty
1	60010099	Screw 2.9×13	2
2	60010599	Valve Bottom Connector	1
3	60010080	O-Ring 25×3.55	1
4	60010077	O-Ring 78.74×5.33	1
5	60095614	O-Ring 30×2.65	1
6	60095063	End Cover	1
7	60010596	Screw 5×12	5
8	60095061	Valve Body	1
9	60010069	Secure Clip	2
10	optional sizes	Drain Line Flow Washer	1
11	60010044	O-Ring 12×2	2
12	60090001	Drain Fitting	1
13	60095060	Spacer (Before June 2022 Only)	1
14	60010409	Seals and Spacers kit	1
15	60010129	Upflow Piston Assembly	1
60010171	Downflow Piston Assembly
16	60010645	End Plug Retainer	1
17	60010075	Screw 5×12	3
18	60010417	Brine Valve	1
19	60090004	Brine Line Elbow	1
20	60010184	Nut 3/8 BLFC	1
21	60010188	O-Ring BLFC Holder	1
22	optional sizes	Brine Line Flow Washer	1
23	60010293	Brine Line Flow Washer Holder	1
24	60010191	Check Ball (Downflow Valve Only)	1
25	60010187	O-Ring 8×1.5	2
26	60010186	O-Ring 12.5×1.5	2
27	60010175	Injector Plug Body	1
28	60010190	O-Ring 32×3	1
29	60010189	O-Ring 18×3	1
30	60010174	Injector Fixed Sleeve	1
31	optional sizes	Injectors	1
32	60010192	Injector Screen	1
33	60095076	Injector Plug	1
34	60010193	Injector Cover Body	1
35	60010195	O-Ring 40×2.65	1
36	60010194	Injector Cover Cap	1
37	60010196	Screw 5×25	4

Novo Water 485UF 485 High Efficiency Softeners fig-28

Bypass Parts List

	No.	Part #	Description	Qty
60095101		60010115	Meter Cable	1
16	60010562	Small O-ring on Connector(Outlet)	3
15	60010079	Valve-Bypass Connector(Inlet)	1
14	60010101	Valve-Bypass Connector(Outlet)	1
13	60010561	Big O-ring on Connector(Outlet)	1
12	60010046	SS Clip	2
11	60010701	Screw on SS Clip	2
10		063 Bypass Body	1
	9	60010006	Bypass Tool	1
8	60010044	O-ring on Plug	2
7	60010209	Bypass Plug	2
6	60095090	Shaft Clip	2
5	92846	Plug Clip	2
	4	60010026	O-ring on Inlet and Outlet	2
3	60010019	Straight 1” NPT Inlet and Oulet	2
2	60010023	Elbow 3/4” NPT Inlet and Oulet	2
1	60010025	Secure Clip Inlet and Oulet	2

Cabinet Parts List

Novo Water 485UF 485 High Efficiency Softeners fig-30

No.	Part #	Description	Qty
22	55010023	0435 Brine Valve Assembly	1
21	55010010	0435 Brine Well	1
20	55020002	4″ Brine Well Cap	1
19		Plastic Screw M8×20	1
18		Hoop Clinch	1
17	60010362	4″ Brine Well Clamp	1
16	85010132	Salt Lid(CS5)	1
15		High Cover(CS5)	1
14	80080015	Control Plate Label	1
13	80080021	Control Plate(CS5)	1
12	60010180	85UF Display Board	1
11		Transparent Back Cover	1
No.	Part #	Description	Qty
---	---	---	---
10		Screw 2.9×6.5	10
9	302171	Drain Line Clamp	1
8	60095097-1	Canature Bypass Valve C/W Meter	1
7	10010061	Control Valve Assembly(CS5)	1
6	18280	Top Cone	1
5	50010020	D-Tube(35“)	1

4

| 205020019| Tank 09×35 (No Base) Model 75C| ****

1

205020020| Tank 10×35 (No Base) Model 100C

3

| | Pressure Tank Protection 9″| ****

2

| Pressure Tank Protection 10”

2

| 25020019| TANK ASSY CS5H-1035| ****

1

25020020| TANK ASSY CS5H-1035

1

| 50010011| 9“ Tank Base| ****

1

50010013| 10“ Tank Base

LEVEL 2 PROGRAMMING (OPTIONAL SETTINGS)

CAUTION: DO NOT CHANGE LEVEL 2 SETTINGS WITHOUT CONSULTING A CANATURE WATERGROUP TECHNICIAN (1-877-288-9888). Incorrectly changing the settings can result in malfunction of the unit.
When the Level 2 Master Programming Mode is entered, all available option setting displays may be viewed and set as needed. Depending on current option settings, some parameters cannot be viewed or set. Novo Water 485UF 485 High
Efficiency Softeners fig-31

To change any setting under level 2 programming:

MASTER PROGRAMMING

Press Up and Down Buttons together for 5 seconds
P ress MANUAL REGEN Button and and change value using Up and Down Buttons

Key Pad Setting
SETTINGS This function is to enter the basic set-up information required at the time of installation.
MANUAL This function is to initiate an immediate or delayed manual REGEN regeneration.
DOWN / Increase or decrease the value of the settings while in the UP programming mode.

Main Valve Settings

SOFTENER UPFLOW (UF)
This mode is for the operation of an up flow regenerating softener. The amount of salt used each regeneration is proportional to the capacity remaining in the system. A preset amount of brine (Default is 70%) is prepared after a normal regeneration. Just before a regeneration is scheduled, fresh water is added to the brine tank to “top off” the already prepared 70% of brine. The total amount of brine used to regenerate the system is proportional to the capacity remaining.
I.e. If the system has 10% capacity remaining, then only 90% of the salt dosage is needed to restore capacity to 100%. 70% of the brine is already prepared (and fully saturated) so 20% is added so that the total of 90% is prepared.
When a standard regeneration is started, the valve will move first to the refill position to add water to the brine tank. The amount of water added is equal to the calculated refill time for the salt dosage X Brine Tank Refill%. The valve then will return to service for the amount of Brine Make Time. When this is com-plete the valve will move to the Brine position.
The regeneration sequence is 1. BRINE MAKE (REFILL), 2. BRINE, 3. BACKWASH, 4 RINSE, 5. RE-FILL.
LANGUAGE
Current available language is English.

UNITS
Current unit of measure is gallons. Metric units may become available at a later date.

EFFICIENCY & CAPACITY SETTINGS
There are 3 settings to choose in Settings. High Efficiency, Standard Capacity, and Iron & Manganese. The values for these settings are set in the Factory Options and are used to calculate the system capacity and refill time.

REFILL
This value should match the BLFC flow washer. It is used to calculate the refill time.

BRINE MAKE TIME
This value is the time allowed for the salt to dissolve in the water to create the brine solution. The value is the amount of time ahead of the scheduled regeneration time that the water will be added to “top off” the brine already prepared in the brine tank.

BRINE PRE-FILL%
This is the percentage of the water that will be added to the brine tank after a regeneration. The default is 70%. The remaining amount of water will be added just prior to the regeneration and will be proportional to the amount of capacity left in the system.

DAILY RESERVE
This value is used to calculate the reserve capacity. Reserve Capacity = No. People x DAILY RESERVE.

DAY OVERRIDE
This setting can be used to add a number of days to override the meter. As an example, if the setting is 5, the system will regenerate after 5 days even if there is still gallons capacity remaining. OFF will cancel this feature.

RINSE OVERRIDE
This setting can be used to skip the RINSE cycle. As an example if the setting is 10, the system will skip 10 rinse. OFF will cancel this feature.

BW OVERRIDE
This setting can be used to skip the backwash cycle. As an example if the setting is 10, the system will skip 10 backwash cycles. The setting will only work if the WATER TYPE is set to CITY for clean water applications.

FORCED REGEN
When set to ON, the system will start a forced regeneration when the remaining capacity reaches 3%. The regeneration consists of 8 minutes of Brine and 12 minutes of Rinse. The 20 minutes regeneration will restore up to 33% of the system capacity. At the next regeneration time (2:00 AM), the system will automatically perform a standard regeneration to restore capacity to 100%.

SMART CLEAN

When set to ON, the system will perform a 10-minute backwash and 10-minute rinse if there is no water flow detected after 7 days. The regeneration will occur at the REGEN TIME.

85UF Upflow Softener Programming

85UF SOFTENER ‐Programming Effective MFG Date 08/15/2019

MASTER SETTINGS| PRESS & HOLD| 

◼▲▼

| or| PRESS & HOLD| ▼| CODE 919|
UNIT SIZE| ‐75C| ‐100C| ‐75| ‐100| ‐150| ‐200| ‐250| ‐300
VALVE TYPE| UF UF| 85UF| 85UF| 85UF| 85UF| 85UF| 85UF| 85UF
SOFTWARE VER.| DEFAULT| DEFAULT| DEFAULT| DEFAULT| DEFAULT| DEFAULT| DEFAULT| DEFAULT
METER TYPE| TB‐H| TB‐H| TB‐H| TB‐H| TB‐H| TB‐H| TB‐H| TB‐H
METER RATIO| A:2.90 K:0.568| A:2.90 K:0.568| A:2.90 K:0.568| A:2.90 K:0.568| A:2.90 K:0.568| A:2.90 K:0.568| A:2.90 K:0.568| A:2.90 K:0.568
POWER FREQ.| 60 Hz| 60 Hz| 60 Hz| 60 Hz| 60 Hz| 60 Hz| 60 Hz| 60 Hz
Service Delay| 3.0| 3.0| 3.0| 3.0| 3.0| 3.0| 3.0| 3.0
Backwash Delay| 7.0| 7.0| 7.0| 7.0| 7.0| 7.0| 7.0| 7.0
Brine Delay| 4.0| 4.0| 4.0| 4.0| 4.0| 4.0| 4.0| 4.0
Rinse Delay| 5.0| 5.0| 5.0| 5.0| 5.0| 5.0| 5.0| 5.0
Refill Delay| 4.0| 4.0| 4.0| 4.0| 4.0| 4.0| 4.0| 4.0
ADVANCED SETTINGS| PRESS & HOLD| 

▲▼



| or| PRESS & HOLD| ▼| CODE 100| |
LANGUAGE| ENGLISH| ENGLISH| ENGLISH| ENGLISH| ENGLISH| ENGLISH| ENGLISH| ENGLISH
UNITS| GALLONS| GALLONS| GALLONS| GALLONS| GALLONS| GALLONS| GALLONS| GALLONS
HARDNESS UNITS| gpG| gpG| gpG| gpG| gpG| gpG| gpG| gpG
HIGH EFFICIENCY| 3.0 lbs/CUFT| 3.0 lbs/CUFT| 3.0 lbs/CUFT| 3.0 lbs/CUFT| 3.0 lbs/CUFT| 3.0 lbs/CUFT| 3.0 lbs/CUFT| 3.0 lbs/CUFT
HIGH EFFICIENCY| 5000 Grains| 5000 Grains| 5000 Grains| 5000 Grains| 5000 Grains| 5000 Grains| 5000 Grains| 5000 Grains
STD CAPACITY| 6.0 lbs/CUFT| 6.0 lbs/CUFT| 6.0 lbs/CUFT| 6.0 lbs/CUFT| 6.0 lbs/CUFT| 6.0 lbs/CUFT| 6.0 lbs/CUFT| 6.0 lbs/CUFT
STD CAPACITY| 4100 GRAINS| 4100 GRAINS| 4100 GRAINS| 4100 GRAINS| 4100 GRAINS| 4100 GRAINS| 4100 GRAINS| 4100 GRAINS
IRON & MN| 12.0 lbs/CUFT| 12.0 lbs/CUFT| 12.0 lbs/CUFT| 12.0 lbs/CUFT| 12.0 lbs/CUFT| 12.0 lbs/CUFT| 12.0 lbs/CUFT| 12.0 lbs/CUFT
IRON & MN| 2500 GRAINS| 2500 GRAINS| 2500 GRAINS| 2500 GRAINS| 2500 GRAINS| 2500 GRAINS| 2500 GRAINS| 2500 GRAINS
REFILL FLOWRATE| 0.20 gpM| 0.20 gpM| 0.20 gpM| 0.20 gpM| 0.20 gpM| 0.20 gpM| 0.20 gpM| 0.20 gpM
BRINE MAKE TIME| 30 MINUTES| 30 MINUTES| 30 MINUTES| 30 MINUTES| 30 MINUTES| 30 MINUTES| 30 MINUTES| 30 MINUTES
BRINE PRE‐FILL %| 70%| 70%| 70%| 70%| 70%| 70%| 70%| 70%
DAILY RESERVE| 75 GAL| 75 GAL| 75 GAL| 75 GAL| 75 GAL| 75 GAL| 75 GAL| 75 GAL
DAY OVERIDE| OFF| OFF| OFF| OFF| OFF| OFF| OFF| OFF
RINSE OVERIDE| OFF| OFF| OFF| OFF| OFF| OFF| OFF| OFF
BW. OVERIDE| 10| 10| 10| 10| 10| 10| 10| 10
FORCED REGEN.| ON| ON| ON| ON| ON| ON| ON| ON
SMART CLEAN| OFF| OFF| OFF| OFF| OFF| OFF| OFF| OFF
SETTINGS| PRESS & HOLD| 

◼

|
TIME OF DAY| SET| SET| SET| SET| SET| SET| SET| SET
YEAR| SET| SET| SET| SET| SET| SET| SET| SET
MONTH| SET| SET| SET| SET| SET| SET| SET| SET
DAY| SET| SET| SET| SET| SET| SET| SET| SET
SET HARDNESS| 25.0 gpG| 25.0 gpG| 25.0 gpG| 25.0 gpG| 25.0 gpG| 25.0 gpG| 25.0 gpG| 25.0 gpG
SET PEOPLE| 4| 4| 4| 4| 4| 4| 4| 4
SALT SETTING| STANDARD| STANDARD| STANDARD| STANDARD| STANDARD| STANDARD| STANDARD| STANDARD
WATER SOURCE| WELL / OTHER| WELL / OTHER| WELL / OTHER| WELL / OTHER| WELL / OTHER| WELL / OTHER| WELL / OTHER| WELL / OTHER
REGEN TIME| 2:00 AM| 2:00 AM| 2:00 AM| 2:00 AM| 2:00 AM| 2:00 AM| 2:00 AM| 2:00 AM
LOAD DEFAULT| NO| NO| NO| NO| NO| NO| NO| NO
AUX OPTIONS| PRESS & HOLD| 

▼

3 Yellow

BLFC Washer| 0.3 GPM| 0.3 GPM| 0.3 GPM| 0.3 GPM| 0.3 GPM| 0.3 GPM| 0.3 GPM| 0.3 GPM
DLFC Washer| #2 2.0 GPM| #3 2.4 GPM| #1 1.5 GPM| #2 2.0 GPM| #3 2.4 GPM| #5 3.5 GPM| #A 5.0 GPM| #A 5.0 GPM
UPPER CONE| YES| YES| YES| YES| YES| YES| YES| YES

85HE Downflow Softener Programming

85DF SOFTENER ‐Programming Effective MFG Date 08/15/2019

MASTER SETTINGS| PRESS & HOLD| 

◼▲▼

| or| PRESS & HOLD| ▼| CODE 919|
UNIT SIZE| ‐75C| ‐100C| ‐75| ‐100| ‐150| ‐200| ‐250| ‐300
VALVE TYPE| 85DF| 85DF| 85DF| 85DF| 85DF| 85DF| 85DF| 85DF
SOFTWARE VER.| DEFAULT| DEFAULT| DEFAULT| DEFAULT| DEFAULT| DEFAULT| DEFAULT| DEFAULT
METER TYPE| TB‐H| TB‐H| TB‐H| TB‐H| TB‐H| TB‐H| TB‐H| TB‐H
METER RATIO| A:2.90 K:0.568| A:2.90 K:0.568| A:2.90 K:0.568| A:2.90 K:0.568| A:2.90 K:0.568| A:2.90 K:0.568| A:2.90 K:0.568| A:2.90 K:0.568
POWER FREQ.| 60 Hz| 60 Hz| 60 Hz| 60 Hz| 60 Hz| 60 Hz| 60 Hz| 60 Hz
Service Delay| 5.0| 5.0| 5.0| 5.0| 5.0| 5.0| 5.0| 5.0
Backwash Delay| 2.0| 2.0| 2.0| 2.0| 2.0| 2.0| 2.0| 2.0
Brine Delay| 2.0| 2.0| 2.0| 2.0| 2.0| 2.0| 2.0| 2.0
Rinse Delay| 5.0| 5.0| 5.0| 5.0| 5.0| 5.0| 5.0| 5.0
Refill Delay| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0
ADVANCED SETTINGS| PRESS & HOLD| 

▲▼



| or| PRESS & HOLD| ▼| CODE 100| |
LANGUAGE| ENGLISH| ENGLISH| ENGLISH| ENGLISH| ENGLISH| ENGLISH| ENGLISH| ENGLISH
UNITS| GALLONS| GALLONS| GALLONS| GALLONS| GALLONS| GALLONS| GALLONS| GALLONS
HARDNESS UNITS| gpG| gpG| gpG| gpG| gpG| gpG| gpG| gpG
HIGH EFFICIENCY| 3.0 lbs/CUFT| 3.0 lbs/CUFT| 3.0 lbs/CUFT| 3.0 lbs/CUFT| 3.0 lbs/CUFT| 3.0 lbs/CUFT| 3.0 lbs/CUFT| 3.0 lbs/CUFT
HIGH EFFICIENCY| 5000 Grains| 5000 Grains| 5000 Grains| 5000 Grains| 5000 Grains| 5000 Grains| 5000 Grains| 5000 Grains
STD CAPACITY| 6.0 lbs/CUFT| 6.0 lbs/CUFT| 6.0 lbs/CUFT| 6.0 lbs/CUFT| 6.0 lbs/CUFT| 6.0 lbs/CUFT| 6.0 lbs/CUFT| 6.0 lbs/CUFT
STD CAPACITY| 4100 GRAINS| 4100 GRAINS| 4100 GRAINS| 4100 GRAINS| 4100 GRAINS| 4100 GRAINS| 4100 GRAINS| 4100 GRAINS
IRON & MN| 12.0 lbs/CUFT| 12.0 lbs/CUFT| 12.0 lbs/CUFT| 12.0 lbs/CUFT| 12.0 lbs/CUFT| 12.0 lbs/CUFT| 12.0 lbs/CUFT| 12.0 lbs/CUFT
IRON & MN| 2500 GRAINS| 2500 GRAINS| 2500 GRAINS| 2500 GRAINS| 2500 GRAINS| 2500 GRAINS| 2500 GRAINS| 2500 GRAINS
REFILL FLOWRATE| 0.30 gpM| 0.30 gpM| 0.30 gpM| 0.30 gpM| 0.30 gpM| 0.30 gpM| 0.30 gpM| 0.30 gpM
DAILY RESERVE| 75 GAL| 75 GAL| 75 GAL| 75 GAL| 75 GAL| 75 GAL| 75 GAL| 75 GAL
DAY OVERIDE| OFF| OFF| OFF| OFF| OFF| OFF| OFF| OFF
RINSE OVERIDE| OFF| OFF| OFF| OFF| OFF| OFF| OFF| OFF
BW. OVERIDE| OFF| OFF| OFF| OFF| OFF| OFF| OFF| OFF
FORCED REGEN.| OFF| OFF| OFF| OFF| OFF| OFF| OFF| OFF
SMART CLEAN| OFF| OFF| OFF| OFF| OFF| OFF| OFF| OFF
SETTINGS| PRESS & HOLD| ◼



|
TIME OF DAY| SET| SET| SET| SET| SET| SET| SET| SET
YEAR| SET| SET| SET| SET| SET| SET| SET| SET
MONTH| SET| SET| SET| SET| SET| SET| SET| SET
DAY| SET| SET| SET| SET| SET| SET| SET| SET
SET HARDNESS| 25.0 gpG| 25.0 gpG| 25.0 gpG| 25.0 gpG| 25.0 gpG| 25.0 gpG| 25.0 gpG| 25.0 gpG
SET PEOPLE| 4| 4| 4| 4| 4| 4| 4| 4
SALT SETTING| STANDARD| STANDARD| STANDARD| STANDARD| STANDARD| STANDARD| STANDARD| STANDARD
WATER SOURCE| WELL / OTHER| WELL / OTHER| WELL / OTHER| WELL / OTHER| WELL / OTHER| WELL / OTHER| WELL / OTHER| WELL / OTHER
REGEN TIME| 2:00 AM| 2:00 AM| 2:00 AM| 2:00 AM| 2:00 AM| 2:00 AM| 2:00 AM| 2:00 AM
LOAD DEFAULT| NO| NO| NO| NO| NO| NO| NO| NO
AUX OPTIONS| PRESS & HOLD| 

▼

3 Yellow

BLFC Washer| 0.3 GPM| 0.3 GPM| 0.3 GPM| 0.3 GPM| 0.3 GPM| 0.3 GPM| 0.3 GPM| 0.3 GPM
DLFC Washer| #2 2.0 GPM| #3 2.4 GPM| #1 1.5 GPM| #2 2.0 GPM| #3 2.4 GPM| #5 3.5 GPM| #A 5.0 GPM| #A 5.0 GPM
UPPER CONE| YES| YES| YES| YES| YES| YES| YES| YES

Toll-Free: 1-877-288-9888 www.canaturewg.com