milwaukee M18 CARRY-ON 3600W/1800W Power Supply Instruction Manual

OPERATOR’S MANUAL

Cat. No. / No de cat.
2845-20M18™
™ 3600W/1800W POWER SUPPLY
SOURCE D’ALIMENTATION DE 3 600 W / 1 800 W M18™

WARNING To reduce the risk of injury, user must read and understand operator’s manual.

IMPORTANT SAFETY INSTRUCTIONS

WARNING Read all safety warnings, instructions, illustrations and specifica- tions provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.

• Know your power supply. Read operator’s manual carefully. Learn its applications and limitations, as well as the specific potential hazards related to this product. Do not alter or modify the power supply from the original design or function. Misuse and improper handling can cause injury.
• Always follow all safety rules recommended by the manufacturer of attachments.
• Do not use this power supply to provide power for emergency medical equipment or life support devices.

WORK AREA SAFETY

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.
• To reduce the risk of injury, close supervision is necessary when an appliance is used near children.
• Do not expose to rain. Store indoors.
• For indoor use or temporary outdoor use. Exercise reasonable care when using in wet conditions. Do not charge outdoors.
• If using with a lanyard, do not exceed maximum capacity marked on the lanyard label. Always determine the weight of the product, with all accessories, when selecting the appropriate lanyard system. Exceeding maximum capacity may result in serious injury. See specifications for tool and battery weight.
• For best results, use with energy absorbing lanyards. Ropes, straps or chains may break and cause failure. Do not use with lanyards at full tension. Do not use lanyards longer than 3 feet.
• Never leave the power supply unattended while in use.

ELECTRICAL SAFETY

• Power cord plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

• Connect only to properly grounded outlets.

• Always use a suitable extension cord to reduce the risk of electric shock.

• Unplug the cord from outlet when not in use and before servicing or cleaning.

• Maintain charger cord. When unplugging charger, pull plug rather than cord. Never carry charger by its cord. Keep cord from heat, oil and sharp edges.
  Make sure cord will not be stepped on, tripped over or subjected to damage or stress. Do not use charger with damaged cord or plug. Have a damaged charger replaced immediately.

• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

• Arrange cords carefully to avoid hazardous environments. Tripping or snagging on cords can cause injury and product damage. Do not allow cords to run through puddles or across wet ground.

• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

• To reduce the risk of electric shock, do not put equipment in water or other liquid. Do not place or store appliance where it can fall or be pulled into a tub or sink.

• If operating a equipment in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of an GFCI reduces the risk of electric shock.

• This equipment has arcing or sparking parts which should not be exposed to flammable vapors. Locate equipment at least 18″ (457 mm) above the floor when used in a repair facility.

• Operating this power supply less than 3′ (1 m) from building or other obstruction can cause overheating and damage to the power supply. For proper cooling, allow at least 3′ (1 m) of empty space above and around the power supply.

• Do not connect power supply output to a building’s electrical system.

• The power supply is isolated from the frame and from the AC receptacle ground pin.

• The power supply output is disconnected (isolated) from the AC receptacle ground pin and frame. Therefore, electrical devices that require this connection may not operate.

• Do not exceed the load rating of the extension cord. Be mindful of the individual and accumulative electrical load for all attachments. Exceeding the load capacity of the extension cord could result in overheating, fire, electrical shock, or injury.

• Do not overload the power supply’s capacity. Exceeding the power supply’s wattage/amperage capacity may damage the power supply and/or electrical devices connected to it.

• Equipment may require more power consumptions than this power supply is capable of providing. Check the equipment’s manual to avoid damage to the power supply or risk of personal injury.

PERSONAL SAFETY

• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
• Do not sit or step on the power supply.
• Do not use on a ladder or unstable support. Stable footing on a solid surface enables better control of the power supply in unexpected situations.
• Do not put fingers or hands into the power supply. Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything else that may reduce air flow.
• Always use common sense and be cautious when using tools. It is not possible to anticipate every situation that could result in a dangerous outcome. Do not use this tool if you do not understand these operating instructions or you feel the work is beyond your capability; contact Milwaukee Tool or a trained professional for additional information or training.

BATTERY AND CHARGER SAFETY

CAUTION
Use MILWAUKEE Li-Ion battery packs only on recommended
MILWAUKEE Li-Ion products. Do not use counterfeit, aftermarket, or “knockoff” batteries or charg- ers. Do not wire a battery pack to a power supply plug or car cigarette lighter.

• Avoid dangerous environments. Do not charge battery pack in rain, snow, damp or wet locations.Do not use battery pack or charger in the presence of explosive atmospheres (gaseous fumes, dustor flammable materials) because sparks may begenerated when inserting or removing battery pack,possibly causing fire.
• Charge in a well ventilated area. Do not blockcharger vents. Keep them clear to allow properventilation. Do not allow smoking or open flames near a charging battery pack. Vented gases may explode.
• Follow all charging instructions and do notcharge the battery pack or equipment outside the temperature range specified in the instructions. Charging improperly or at temperaturesoutside the specified range may damage the batteryand increase the risk of fire.
• Avoid using an extension cord when possible. When unavoidable, use a properly wired 16 gauge or larger extension cord with pins that are the same number, size and shape as the pins on the charger. Make sure that the extension cord is in good electrical condition.
• Unplug charger and remove battery packs when not in use.
• Do not burn or incinerate batteries. Batteries mayexplode. Toxic fumes and materials are createdwhen batteries are burned.
• Do not use a battery pack or equipment that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
• Do not crush, drop, or damage battery pack.Always securely contain battery packs during transport. Do not use a battery pack that hasreceived a sharp blow, been dropped, run over, or damaged in any way (e.g., pierced with a nail, hit with a hammer, stepped on, in a vehicle accident).
• Do not disassemble battery pack or charger. If it is damaged, take it to a MILWAUKEE service facility.
• Battery chemicals cause serious burns. Never allow contact with skin, eyes, or mouth. If a damaged battery pack leaks battery chemicals, userubber or neoprene gloves to dispose of it. If skin is exposed to battery fluids, wash with soap and water and rinse with vinegar. If eyes are exposed to battery chemicals, immediately flush with water for 20 minutes and seek medical attention. Removeand dispose of contaminated clothing.
• Do not short circuit. A short-circuited batterypack may cause fire, personal injury, and product damage. A battery pack will short circuit if a metal object makes a connection between the positiveand negative contacts on the battery pack. Do not place a battery pack near anything that may cause a short circuit, such as coins, keys or nails in your pocket.
• Do not allow fluids to flow into battery pack.Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach containing products, etc., can cause a short circuit.
• Do not expose a battery pack or equipment to fire or excessive temperature. Exposure to fire or tem- perature above 265°F (130°C) may cause explosion.
• Battery packs marked as Resistant are suitable for environments where incidental contact or exposure to oils, greases, and solvents can occur. These packs are not resistant to acids or other corrosive chemicals. Never immerse or allow fluids to penetrate the battery pack.
• Use only recommended attachments. Use of an attachment not recommended or sold by the battery charger or battery pack manufacturer may result in a risk of fire, electric shock or personal injury.

SERVICE

• Have your power supply serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power supply is maintained.
• Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
• Maintain labels and nameplates. These carry important information. If unreadable or missing, contact a MILWAUKEE service facility for a free replacement.

STORAGE

• To prevent the risk of fire or shock; Store your power supply and battery packs in a cool, dry place. Do not store where temperatures may exceed 122°F (50°C) such as in direct sunlight, a vehicle, or metal building during the summer.

READ AND SAVE ALL INSTRUCTIONS FOR FUTURE USE.

SPECIFICATIONS

Cat. No. …………………………………………….. 2845-20
Battery Type ………………………………………….M18™
Charger Type…………………………………………M18™
Rated Input Voltage …………………………… 120 V AC
Rated Input Amps ……………………………………..8.4 A
Rated Output Voltage (Charger) …………………. 18 V
Rated Output Amps (Per Charger) …………………3 A Total Rated Output (Both Receptacles)
Peak Watts …………………….3600 W for 5 seconds
Rated Watts ………………………………………. 1800 W
Voltage……………………………………………. 120 VAC
Rated Frequency …………………………………… 60 Hz Rated Output Voltage
(USB-A) ……………………… 5VDC @ 2.1A (10.5 W) Rated Output Voltage
(USB-C PD) ………………………….20/15/12/9/5VDC @ 3A (Up to 60 W)
Power Supply Cord…………….UL Listed, Type SJO, 3-conductor, No. 14 AWG min., rated 105°C min., 300V/15A min., 6 ft (1.8 m) min. length
Weight (Tool Only) ……………………….28 lb (12.7 kg) Weight (With four M18™
12.0Ah battery pack) ……………….41.7 lb (18.9 kg) Recommended Ambient
Operating Temperature ………………..32°F to 105°F (0°C to 40°C)
Recommended Ambient
Charging Temperature …………………40°F to 105°F (5°C to 40°C)

FUNCTIONAL DESCRIPTION

1. Power button
2. Battery presence indicator
3. Lock icon
4. Handle
5. Battery lock bars
6. Battery charging status/indicator light (4 total)
7. Battery pack slots
8. Carrying strap loop
9. Fans
10. USB-A port| 11. USB-C PD port
12. AC input
13. AC 120V AC receptacles
14. Bonding terminal
15. Overtemp indicator
16. Overload indicator
17. Fuel gauge
18. Roll cage
19. Detachable charging cord (not shown)
---|---

SYMBOLOGY

INSTALLATION

EXTENSION CORDS
Grounded tools require a three wire extension cord. Double insulated tools can use either a two or three wire extension cord. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool
damage. Refer to the table shown to determine the required minimum wire size.
The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
When using more than one extension cord to make up the total length, be sure each cord contains at least the minimum wire size required. If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum wire size. Guidelines for Using Extension Cords

• Do not exceed the load rating of the extension cord. Be mindful of the individual and accumulative electrical load for all attachments. Exceeding the load capacity of the extension cord could result in overheating, fire, electrical shock, or injury.
• If you are using an extension cord outdoors, be sure it is marked with the suffix “W” to indicate that it is acceptable for outdoor use.
• Be sure your extension cord is properly wired and  ingood electrical condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it.
• Protect your extension cords from sharp objects, excessive heat and damp or wet areas.

Recommended Minimum Wire Gauge
For Extension Cords*

Nameplate
Amps| Extension Cord Length
25′| 50′| 75′| 100′| 150′
0 – 2.0| 18| 18| 18| 18| 16
2.1 – 3.4| 18| 18| 18| 16| 14
3.5 – 5.0| 18| 18| 16| 14| 12
5.1 – 7.0| 18| 16| 14| 12| 12
7.1 – 12.0| 16| 14| 12| 10| —
12.1 – 16.0| 14| 12| 10| —| —
16.1 – 20.0| 12| 10| —| —| —

• Based on limiting the line voltage drop to five volts at 150% of the rated amperes.

GROUNDING

WARNING
Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug pro vided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the cord or plug is damaged. If damaged, have irepaired by a MILWAUKEE service facility beforeuse. If the plug will not fit the outlet, have aproper outlet installed by a qualified electrician. Only if permitted and required by local codes, the bonding terminal stud may be wired using 14 AWG Copper insulated solid or stranded wire or wire sized per local codes.
Grounded Tools (Three-Prong Plugs) Tools marked “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet (See Figure A). If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock. The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool’s grounding system and must never be attached to an electrically “live” terminal.
Your tool must be plugged into an appro- priate outlet, properly installed andgrounded in accordance with all codesand ordinances. The plug and outlet should look like those in Figure A.

ASSEMBLY

WARNING
Recharge only with the charger specified for the battery. For spe- cific charging instructions, read the operator’s manual supplied with your charger and battery.
Removing/Inserting the Batteries To remove the batteries, push in the release buttons and pull the battery packs away from the power source.
To insert the batteries, slide the pack into the body of the power source. Make sure they latch securely into place.
NOTE: The unit requires four charged battery packs to operate.
Inserting/Removing Extension Cord
The power source must be plugged in to charge the batteries. The power source will charge up to 4 batteries that are installed in the charging bays. Plug a suitable extension cord into the power source.
The power source must be plugged in to a 120V receptacle to charge batteries. To disconnect the extension cord once charging is complete, remove the cord from the power source.
The power supply either discharges or charges the battery packs one function at a time. Once battery packs are charged, unplug the extension cord and plug in tools or products.
Locking/Unlocking the Battery Packs

1. Twist the handle collar to unlock the handle prior to pulling apart the battery lock bars attached to the carrying handle.
2.  Twist the handle collar to the lock position. There is a hole in the bar to attach a padlock (not included).
3. Attach the padlock. Doing so prevents the batteries from being removed from the power source.
   NOTE: It is recommended that the battery lock bars be positioned closest together with the handle collar in the lock position when not over battery packs.

Installing the Carrying Strap
To install the carrying strap, attach the hooks from the strap on both carrying strap loops. Make sure the hooks are secure on the loops prior to carrying the power source. To remove, reverse the procedure.
Tethering the Power Supply
Tethers can be attached to the power source anywhere on the roll cage.

GENERAL OPERATION

Power Supply Capacity
Make sure the power supply can supply enough rated and peak watts for the items being powered at the same time.

1. Select the items to be powered at the same time.
2. Total the rated watts of these items. This is the amount of power the power supply must produce to keep the items running. See wattage reference chart.
3. Estimate how many peak watts will be needed. Peak wattage is the short burst of power needed to start electric motor-driven tools such as a circular saw. Because not all motors start at the same time, total peak watts can be estimated by adding only the item with the highest additional peak watts to the total rated watts from step 2.

Application/ Equipment| Estimated Rated Watts| Estimated Peak Watts
---|---|---
Job Site
Electric Drill – 3/8″| 600| 1000
Work Light| 1000| 1000
Reciprocating Saw| 960| 1920
Circular Saw – 7-1/4″| 1400| 2300
Miter Saw – 10″| 1800| 2800
Air Compressor 1/4 HP| 970| 1600
Airless Sprayer 1/3 HP| 600| 1200
Radio| 50| 50
M18™/M12™ Standard Charger (48-59-1812)|

60

|

60

M18™/M12™ Rapid Charger (48-59-1808)| 75 (M12™)

120 (M18™)

| 75 (M12™)

120 (M18™)

Lifestyle
Microwave| 1000| 1000
TV| 50-300| 50-300
Satellite Receiver| 250| 250
Portable Fan| 40| 120
Heater| 1300| 1300
String Lights| 50-150| 50-150
Laptop| 50-150| 50-150
Tablet| 15| 15
Cellphone| 5| 5
*Wattages listed are approximate. Check tool or appliance for actual wattage.

Fuel Gauge
Use the Fuel Gauge to deter mine the battery pack’s remaining run time. Press the Fuel Gauge button to display the lights. The Fuel Gauge will light up for 2-3 seconds. When less than10% of charge is left, 1 light on the Fuel Gauge will flash slowly.

NOTE: If the Fuel Gauge doesn’t appear to be working, place the battery pack on the charger and charge as needed.
Compared to NiCd battery pack types, MILWAUKEE Li-Ion battery packs deliver fade-free power for their entire run time. The tool will not experience a slow, gradual loss of power as you work. To signal the end of discharge, 1 light on the Fuel Gauge will flash quickly for 2-3 seconds and the tool will not run. Charge the battery pack.
NOTE: Immediately after using the battery pack, the Fuel Gauge may display a lower charge than it will if checked a few minutes later. The battery cells “recover” some of their charge after resting.

power supply, then retry.
Lights 1&3 / 2&4, flashing alternatingly| Battery temperature too high| Allow batteries to cool, then retry.

Using the Power Supply
This power supply converts DC electricity to 120 VAC household power and/or USB charging power, allowing the user to charge and power a variety of devices.

• To prolong the life of the power supply and attached devices, it is important to take care when adding electrical loads to the power supply.
• There should be nothing connected to the power supply outlets before starting the power source.
• The correct and safe way to manage power supply power is to sequentially add loads.

NOTE: The AC Outlet and USB ports can be used at the same time. The internal fan may activate during use.

1. Insert (4) required M18™ battery packs.
2. Press the power button to turn the power supply ON.
3. Plug in and turn on the first load, preferably the largest load. Permit the power supply output to stabilize.
4. Plug in and turn on the next load. Again, permit the power supply to stabilize.
   NOTE: An alert will sound when the battery packs are low. 5. When finished, turn off the power supply, disconnect the devices, and remove the battery packs.

Onboard Fuel Gauge LEDs and Alert Tones
When the power source detects a low battery condition, a dead battery, an overload, or overtempcondition, the user will be alerted with an audible tone(s). Investigate the root cause of the tone(s) to continue use.
Overload and Overtemperature Conditions
When an overload or overtemperature condition occurs, the power source will produce a unique tone and the respective icon will light. Take the appropriate action, such as turning off or reducing the load on the power source, or allowing the power source to rest (cool down) before continuing use.
NOTE: After three consecutive overloads, the power supply will be locked out for 5 minutes. After 5 minutes, the power supply can be turned on and used normally.
Cold Weather Operation
MILWAUKEE Lithium-Ion battery packs are designed to operate in temperatures below freezing. When the battery pack is too cold, it may need to warm up before normal use. Insert four batteries on the power supply and use the power supply in a light application (up to 1000W). If the above power recommendation is exceeded, an audible tone will be heard, and 1 LED might flash on the battery fuel gauges. Reset the battery packs by plugging them into a charger (the power supply acts as a charger when plugged into AC power).

CHARGER OPERATION

WARNING Charge only MILWAUKEE M18™Lithium-Ion batteries in this MILWAUKEE Lithium-Ion charger. Other types of batteries may cause personal injury and damage. When to Charge the Battery Pack MILWAUKEE batteries do not develop a “memory” when charged after only a partial discharge. It is not necessary to run down the battery pack before placing it on the charger.

• Use the Fuel Gauge to determine when to charge your MILWAUKEE Lithium-Ion battery pack.
• You can “Top-Off” your battery packs’ charge beforestarting a big job or long day of use.
• The only time it is necessary to charge theMILWAUKEE Lithium-Ion battery pack is when the battery pack has reached the end of its charge. To signal the end of charge, the power supply will beepand flash the fuel gauge. Charge the battery pack as needed.

How to Charge the Battery Pack

1. Connect 120V power cord to AC input.
   NOTE: When an extension cord is connected to the AC input, power supply will enter charging mode.

2. Insert one or more battery packs in available battery pack slots. Make sure it latches securely into place. The fuel gauge on each battery pack indicates how fully charged the pack is. The fuel gauge will turn off when charging is complete.
   NOTE: Battery packs will charge simultaneously.

3. Once inserted, the LED for the corresponding charging indicator will light. Battery packs will charge simultaneously. The LEDs will indicate the following:

Continuous red: Charging
Slow flashing green: Approaching full charge
Continuous green light: Charging is complete
Flashing red: Battery is too hot/cold – Charging will begin when battery reaches correct charging temperature

NOTE: When in charging mode, the power supply cannot use AC outlets or USB ports.
4. After charging is complete, the charge indicator light will be illuminated green. The power supply will keep the battery pack fully charged if it is left on the charger. The charge indicator light will be same as normal charging.

• If the charge indicator light flashes red and green, check that the battery pack is fully seated into the bay. Remove the battery pack and reinsert. If the charge indicator light continues to flash red and green, remove pack(s) and unplug charger for at least 2 minutes. After 2 minutes, plug charger back in and insert pack. If the problem persists, contact a MILWAUKEE service facility.
• If the charge indicator light does not come on, check that the battery pack is fully seated into the bay. Remove the battery pack and reinsert. If the charge indicator light still does not come on, remove pack(s) and unplug charger for at least 2 minutes. After 2 minutes, plug charger back in and insert pack. If after these attempts the charge indicator light still does not come on, contact a MILWAUKEE service facility.

Dead Battery Notification
Alarm will sound when a battery’s charge becomes low. An additional alarm will sound when the unit is dead and powers off.
Charging a Hot or Cold Battery Pack
The Red Flashing charge indicator light on the charger indicates that the battery pack temperature is outside the charging range. Once the battery pack is within the acceptable range, normal charging will take place and the red light will be continuous. Hot or cold batteries may take longer to charge.

Lithium-Ion Charging Status

Battery Pack Temperature| Red Charger Indicator Light| Charging Status
Too Hot Normal Range

Too Cold

| Fast Flashing Continuous Fast Flashing| Not charging Normal charging Not charging

MAINTENANCE

WARNING To reduce the risk of injury, alwaysunplug the power supply and re- move the battery packs from the chargers beforeperforming any maintenance. Never disassemblethe tool, battery packs or charger. Contact aMILWAUKEE service facility for ALL repairs. To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach containing products, etc., can cause a short circuit.
Maintain Power Supply Keep your power supply in good repair by adopting a regular maintenance program. If the power supply does not work properly, return the power supply to a MILWAUKEE service facility for repairs.
WARNING To reduce the risk of personal injury, electric shock and damage, never immerse your tool in liquid or allow a liquid to flow inside it.
Cleaning
Clean dust and debris from any vents. Keep tool clean, dry and free of oil or grease. Use only mild soap and a damp cloth to clean, since certain cleaning agents and solvents are harmful to plastics and other insulated parts. Some of these include gasoline, turpentine, lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia and household detergents containing ammonia. Never use flammable or combustible solvents around tools.
Cleaning the Battery and Battery Bay
Keep battery connections and surfaces between the power source and battery free of debris and materials.
Failure to keep surfaces clean may result in misalignment and/or damage to the battery connection.
Repairs
For repairs, return the tool to the nearest authorized service center.

ACCESSORIES

WARNING
Use only recommended accessories. Others may be hazardous.
For a complete listing of accessories, go online to www.milwaukeetool.com or contact a distributor.
SERVICE – UNITED STATES
1-800-SAWDUST (1.800.729.3878)
Monday-Friday, 7:00 AM – 6:30 PM CST or visit www.milwaukeetool.com
Contact Corporate After Sales Service Technical Support with technical, service/repair, or warranty questions.
Email: metproductsupport@milwaukeetool.com
Become a Heavy Duty Club Member at www.milwaukeetool.com to receive important notifications regarding your tool purchases.

LIMITED WARRANTY USA & CANADA

Every MILWAUKEE power tool* (see exceptions below) is warranted to the original purchaser only to be free from defects in material and workmanship. Subject to certain exceptions, MILWAUKEE will repair or replace any part on an electric power tool which, after examination, is determined by MILWAUKEE to be defective in material or workmanship for a period of three (3) years* after the date of purchase unless otherwise noted. Return of the power tool to a MILWAUKEE factory Service Center location or MILWAUKEE Authorized Service Station, freight prepaid and insured, is required. A copy of the proof of purchase should be included with the return product. This warranty does not apply to damage that MILWAUKEE determines to be from repairs made or attempted by anyone other than MILWAUKEE authorized personnel, misuse, alterations, abuse, normal wear and tear, lack of maintenance, or accidents.
Normal Wear: Many power tools need periodic parts replacement and service to achieve best performance. This warranty does not cover repair when normal use has exhausted the life of a part including, but not limited to, chucks, brushes, cords, saw shoes, blade clamps, o-rings, seals, bumpers, driver blades, pistons, strikers, lifters, and bumper cover washers. This warranty does not cover Air Nailers & Staplers; Airless Paint Sprayer; Cordless Battery Packs; Gasoline Driven Portable Power Generators; Hand Tools; Hoist – Electric, Lever & Hand Chain; M12™ Heated Gear; Reconditioned Product; and Test & Measurement Products. There are separate and distinct warranties available for these products. **The warranty period for Job Site Radios, M12™ Power Port, M18™ Power Source, Jobsite Fan and Trade Titan™ Industrial Work Carts is one (1) year from the date of purchase. The warranty period for the M18 FUEL™ 1″ D-Handle High Torque Impact Wrenches, Drain Cleaning Cables, AIRSNAKE™ Drain Cleaning Air Gun Accessories, REDLITHIUM™ USB Laser Levels and TRAPSNAKE™ 25′ Auger w/ CABLE DRIVE™, FORCE LOGIC™ Press Tool Accessories and Green Cross Line Laser is two (2) years from the date of purchase. The warranty period for the M18™ Compact Heat Gun, 8 Gallon Dust Extractor, M18™ Framing Nailers, M18 FUEL™ 1/2″ Ext. Anvil Controlled Torque Impact Wrench w/ ONE-KEY™, M18 FUEL™ 1″ High Torque Impact Wrench w/ ONE-KEY™, M18 FUEL™ 2 Gal. Compact Quiet Compressor, M12™ Laser Levels, 165′ Laser Detector, M12™ 23GA Pin Nailer, M18 FUEL™ 1/4″ Blind Rivet Tool w/ ONE-KEY™, M12 FUEL™ Low Speed Tire Buffer, M18 FUEL™ Random Orbital Polishers, M18™ Utility Fencing Stapler, 72″ Laser Tripod, and M18™ CARRY-ON™ 3600W/1800W Power Supply is three (3) years from the date of purchase. The warranty period for the LED in the LED Work Light and the LED Upgrade Bulb for the Work Light is the lifetime of the product subject to the limitations above. If during normal use the LED or LED Bulb fails, the part will be replaced free of charge. Warranty Registration is not necessary to obtain the applicable warranty on a MILWAUKEE power tool product.
The manufacturing date of the product will be used to determine the warranty period if no proof of purchase is provided at the time warranty service is requested. ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT AGREE TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, WRITTEN OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. This warranty applies to product sold in the U.S.A. and Canada only. Please consult the ‘Service Center Search’ in the Parts & Service section of MILWAUKEE’s website www.milwaukeetool.com or call 1.800. SAWDUST (1.800.729.3878) to locate your nearest service facility for warranty and non- warranty service on a Milwaukee electric power tool.

SERVICE – CANADA
Milwaukee Tool (Canada) Ltd 1.800.268.4015
Monday-Friday, 7:00 AM – 4:30 PM CST or visit www.milwaukeetool.ca

References

• Milwaukee® Tool Official Site | Nothing but HEAVY DUTY®
• Sitio oficial de Milwaukee® Tool | Nothing but HEAVY DUTY®

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>