DAEMA DWD-0851BC Clothes Dryer User Manual

DAEMA DWD-0851BC Clothes Dryer

SAFETY INFORMATION

1. Micro Control: Simple and convenient operation with the help of PCB board, and it will feel the temperature when drying automatic.
2. Big size door window: See the procedure of drying clearly through this window.
3. Open the door with 180 ° : It is very convenient to put in and out clothes with 180°angle opening range.
4. Compact instruction: Big capacity and unique outlook with anti-dust, anti-humidity, anti shake, long life and low noise design.
5.  The tumble dryer is NOT to be used if industrial chemicals have been used for cleaning.
6. The lint trap has to be cleaned frequently.
7. Lint must not accumulate around the tumble dryer.
8. Adequate ventilation has to be provided to avoid the back flow of gases into the room from appliance burning other fuels, including open fires.
9. Do not dry unwashed items in the tumble dryer.ltems that have been soiled with substance such as cooking oil, acetone, alcohol, petrol,kerosene, spot removers, turpentine,waxes and wax removers should be washed in hot water with a extra amount of detergent before being dried in the tumble dryer.ltems such as foam rubber (latex form), shower caps, waterproof textiles, rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the tumble dryer.
10. If it is unavoidable that fabrics that contain vegetable or cooking oil or have been contaminated by hair care products be placed in a tumble dryer they should first be washed in hot water with extra detergent-this will reduce, but not eliminate, the hazard.
11. Fabric softeners, or similar products, should be used as specified by the fabric softener instructions.The final part of a tumble dryer cycle occurs without heat(cool down cycle) to ensure that the items are left at a temperature the ensure that the items will not be damaged.WARNING: never stop a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.
12. The exhaust air must not be discharged into a flue which is used for exhausting fumes from appliance burning gas or other fuels.
13. The appliance must not be install behind a lockable door,a sliding door or a door with a hinge on the opposite side to that of the tumble dryer. In such a way, full opening of the tumble dryer door is restricted.
14. Oil-affected items can ignite spontaneously,especially when exposed to heat sources such as in a tumble dryer.The items become warm, causing an oxidation reaction in the oil. Oxidation creates heat. If the heat cannot escape, the items can become hot enough to catch fire.Piling, stacking or storing oil-affected items can prevent heat from escaping and so create a fire hazard.
15. The appliance should not be overturned during normal use or maintenance.
16. Remove all objects from pockets especially lighters and matches.
17. Keep away from children.Children should not use this appliance without proper and chose supervision. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
18. For appliances with ventilation openings in the base,that a carpet must not obstruct the opening.
19. If the power cable is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
20. This appliance is for indoor use only.

Correct Disposal of this product:

This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of ma-terial resources.

Installation before use

Part name

1. Topboard
2. Control panel
3. Door
4. Cabinet
5. Filter
6. Power lead
7. Door lock
8. Tumbling box
9. Reset button
10. Start/Pause Button
11. Program Knob

Step1: Power source and grounding.

The dryer employs alternative current with the rated voltage and frequency. When the voltage fluctuates between 10% of rated voltage, the dryer can work normally. A special power socket should be used for the dryer for convenience and safety. The method of connection of the socket is as the figure below.

NOTICE:

The socket and the grounding wire must be installed by an electrician to prevent incorrect installation or use of the socket and to guarantee the safety of use of electricity. The power wire of the dryer employs Y connection ,if the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. No connection of the grounding wire with the neutral wire, otherwise the cabinet will be charged,which is likely to cause the danger of electric shock.

Step2: Precautions

◆   Do not store or install the dryer where it will be exposed to water or the weather. If unavoidable, please dry the dryer before each use.| ◆    Please install dryer in a well ventilated area for better air circulation and  to avoid obstructing air intake passage .
---|---
◆ To aviod problems from wet clothes minimize risk, dehydrate items before placing inside the dryer .| ◆    Do not spray combustible aerosols near the dryer during use. If accidental spray occurs do not touch the plug or start/ pause button .
◆    Do not dry any clothes that are contaminated with combustible materials: i.e. Gasoline, methylated spirits, etc.| ◆    Do not operate this dryer if it is damaged ,

malfunctioning ,partially disassembled or has missing or broken parts .

◆    When the dryer is working, the back side will become hotter . In order to avoid such risk , The dryer is not intended for use by young children or infirm persons without supervision .| ◆    Please do not use the machine if your feet or hands are wet .
◆     To avoid deformation of the control  panel, do not place any heavy or hot articles on top of the dryer.| ◆    Do not try to dry raincoat or fluff clothes, or items containing rubber or  elastic  materials on any heat setting.
---|---
◆     To avoid scalding, do not open the dryer door until the program has completed

|

This product belongs to type I electronic products and please take note of safety problem accordingly:

1. lt is rule to use power which is buried in the earth and will not touch any social equipments such as gas pipe or water pipe etc. Make sure the difference of different lines and they are not connected.

2. Please use special socket which is according to National Standard and will endure 13 A current.

To be safe, please make improvements as soon as possible according to the rules and suggestions mentioned above .

Clothes with the following markings shall not be dried in this dryer.

Simple Installation

Step 1:
Dryer should be placed in a ventilated area with no less than 15 cm distance from the wal. If placed in a room such as bath room, it is suggested there are no obstacles of 1.5m in front of dryer and it is kept ventilated.

Step 2: The horizontal adjustment
Tie a heavy subject on the string on the front and two sides of the dryer. Please refer this to below figure, and if A=A, B=B, this means the dryer is placed horizontally. If the objects do not match up, something should be used to level the dryer.

Notice:
If the dryer is not placed horizontally (the lean angels is no more than 2), the dryer will operate unbalanced and be more likely to be faulty.

Notice when installing:

• Do not install the dryer in the open air or place where easily damaged by water;
• Do not place the back of dryer near curtain or other obstacles;
• Do not place the dryer near gas or flammable materials.

Operation explanation

1. Preparing before drying
   Clothes have to be washed and dehydrated before putting in the dryer. Put same kind clothes to dry together. Sort your clothes into loads that take a similar time to dry e.g. Heavier items from light items. Make sure the decorations and buttons are safe for high temperature and will not damage the inner tube of the dryer. Make sure the clothes are wel protected. It is suggested to turn the clothes inside- out. Please check the clothes after washing, if there is dirt on cothes, the drying process cannot be relied on to remove the remaining dirt. Please make sure the power plug is well connected and the supply cord is in good condition.

2. Check filter
   Make sure the filter is well cleaned and in the right position.
   Filter must be cleaned regularly.

3. Put clothes into the dryer
   For faster results it is better put clothes with 1/2-2/3 the capacity of the inner tube tor drying, because drying needs space to make clothes circulate evenly. When drying big clothes, it is better to include several small items to help balance the load. When drying expensive or little clothes 1. 5kg) it is better to add several towels whose fibers wont fall off easily, this will help dry the clothes more evenly. To avoid creased, rough or static electricity clothes, do not over dry.

The reference weight of dry clothing Close the door
Instruction on control panel

1. PROGRAM(Extra Dry, Standard Dry, Mix Dry, Iron DRY, Airing, 5H, 60Min, 30Min)
2. START/PAUSE

• Decide on a program according to the texture and capacity of the clothes.Select the “program konb” to the desireed program.
• Push “STRAT/PAUSE” button, this will strat the program. If you wish to pause the program to add more clothes push the “STRAT/PAUSE” button again. Be careful when opening dryer door,hot steam can release. To continue program, make sure the door is closed then push the “STRAT/PAUSE” button located at the back of the unit.
• If the unit does not heat, push the reset button located at the back of the unit.
• Press the “CREASE GUARD” button if expensive or easily creased clothes are being dried. Crease guard is indicated on/off via the “crease guard” light.
• Push “STRAT/PAUSE” button, this will strat the program. If you wish to pause the program to add more clothes push the “STRAT/PAUSE” button again. Be careful when opening dryer door, hot steam can release. To continue program, make sure the door is closed then push the “STRAT/PAUSE” button once again. When the dryer is in pause mode it is possible a or restat programs.
• Control panel locjk feature is initialized by pushing both “CREASE GUARD” and “HEAT” buttons at the same time. When the lock feature is enable it is indicated by a light, pushing the buttons again will disable this feature.
• Preset: Can make your preset for 12hours at most to start the program, every press a booking, and 1 hour appointments perset during 1-12 hours.

|

’

|

’

| Air-cold|
---|---|---|---|---
30Min| ≤3.0kg|

Wanm clothes

| 10Min| 30Min
60Min| ≤4.0kg| Quick drying Clothes| 10Min| 60Min
2.5H| 5.0-8.5kg| cutton clothes| 10Min| 150Min
Light| ≤4.0kg| chemical and small clothes| 10Min| 90Min
EXTRA| 8.5kg| cotton weaving clothes, jeans and bedsheets| 10Min| 170Min
Nonmal| 4.5-6.0kg| cutton clothes, jeans| 10Min| 130Min
Mix| 4.0-5.0kg| cutton clothes, syhthetic| 10Min| 110Min
Airing| ≤5.0kg| wool, delicate clothes| 10Min| 110Min

Notice
Cold air function circulates cold air for 10 minutes at the end of program. This ensures that the items are left at a temperature, and that the items will not be damaged Crease Guard adds an extra 30s after the program to shake clothes in order to protect against creasing.

• Crease Guard means after programming, it adds extra 30s’ one way running to shake clothes in order to protection of creasing. The inside temperature and humidity will not affect drying time. Check the label attached on clothes and choose the right temperature and time according to the explanation. The few clothes below 2. Okg shall be selected with ” smart “program.

• End of Program
  At the end of program, buzzer rings to remind take out clothes from dryer.

• Take out the Plug
  To be safe, please unplug the unit after each use.

• Clear filter, cabinet and inner tub.
  Accumulated dust, fiber&debris will affect the air circulation inside the dryer. This will cause longer drying times. It is advise to clean the filter and inner tube after each use. Make sure to cut off the power before clearing.

Filter Clean

1. Remover filter
   The lint filter is located in the door opening. remove the lint filter and open it out.

2. Clean filter
   Wipe down with a damp cloth.

3. Re-fit filter
   Once the filter is dry, re-fit into door opening.

4. Wipe the frilter after using every time.

Cleaning cabinet and inner tube
Use a soft damp cloth to wipe the cabinet and inner tube. do not rinse by water directly do not use scour wipes do not use gasoline and alcohol wipes
Make sure open to the front door for aeration after cleaning the inner tube

Other functions description

Step 1: Waming function

buu er sounds every 15 minutes

| Close door

Step 2: Auto power-off function

• This machine will auto power-off after 10 minutes when you do not set any program.
• This machine will auto power-off after 6 time’s buzzer on drying.

Notice

Read before use:

1. Oil-affected items can ignite spontaneously, especially when exposed to heat sources such as in a tumble dryer. The items become warm, causing an oxidation reaction in the oil. Oxidation creates heat. If the heat can not escape, the items can become hot enough to catch fire. Piling, stacking or storing oil affected items can prevent heat from escaping and so create a fire hazard.
2. If it is unavoidable that fabrics that contain vegetable or cooking oil or have been contaminated by hair care products be placed in a tumble dryer they should first be washed in hot water with extra detergent-this will reduce, but not eliminate, the hazard.
3. The final part of a tumble dryer cycle occurs without heat (cool down cycle) to ensure that the items are left at a temperature that ensures that the items will not be damaged. Waming: Never stop a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.
4. This dryer has ventilation openings in the base, carpet must not obstruct the openings.
5. The dryer must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the tumble dryer in such a way that a full opening of the tumble dryer door is restricted.
6. This appliance is not intended for use by persons (including children) with reduced physical , sensory or mental capabilities,or lack of experience and knowledge, unless they have been given supervision or instructions concerning use of the appliance by a person reponsible for their safety.
7. Children should be supersived to ensure that they dont play with the APPLIANCE
8. The lint trap has to be cleaned frequently, lint must not be allowed to accumulate around the tumble dryer.
9. The tumble dryer is not to be usedif industrial chemicals have been used for leaning.
10. Caution, risk of fire symbol-This appliance has a risk of fire, caution should be enforced while operating
11. Items that have been soiled with substances such as cooking oil, acetone, alcohol, pertol, kerosene, spot removers, turpentine, waxes and wax removers should be washed in hot water with an extra amount of detergent before being dired in the tumble dryer.
12. Fabric softeners, or similar products, should be used as specified by the fabric softener instructions. Items such as foam rubber(latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows fitted with foam rubber pads SHOULD NOT be dried in the tumble dryer.

When using:

• If the drying process can operate while the door is open it should be sent to maintenance.
• If the drying process can operate without pushing the”START/PAUSE” button it should be sent to maintenance.
• This dryer is not intended to be placed on top of a washing machine.

Trouble Solution

Check the power socket and make sure plug is connected tight

Remove clothes and check dampness, Max volume of the dryer is 7kg

Please careerman exchange the temperature fuse

Dryer releasing extensive heat| Lint trap requires cleaningIntake or exhaust passage is obstructed| Clean lint trap

Clean air intake and exhaust and check for obstructions.(eg.Curtain)

Wet clothes| Dryer toofull

Clothes left in dryer too long after the end of the program

Clothes not assorted properly Wrong temperature for clothes

| Make sure the dryer is not too full

Immedicately remove clothes when program finished

See page 7.

Observe the maintenance label on clothes

Shrinks clothes| Clothes over dried| Observe the maintenance label on clothing. Remove clothes from dryer while still damp, finish drying process by hang drying.
Lint balls on clothing| Synthetic fibre rubbing with each other cause lint which attaches to clothes| Use fabric softer. Please spray settled gule on cuff and neckline when ironing.

• lf there is no heat from the dryer, please press the plastic push button at rear of dryer to activate the thermostat in order to reheat the element, please see illustration.
  The sound of dryer when runs can cause

• Excessive noise of vibration: Due to heavy wet clothes turning and bumping

• Air bumping: When drying, machine will generate steam which will come out from exhaust pipe. Tthis will cause bumping with the bottom of the inner tub.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>