DAEMA DFZ-368SCCG Display Showcase User Manual
- June 3, 2024
- DAEMA
Table of Contents
DAEMA DFZ-368SCCG Display Showcase
Product Introduction
This appliance adopts the high quality com presser of famous brand, buried or swell-tubular evaporator, and steel-wired condenser. The appliance has rapid refrigeration speed; consumes less electrical power; has refined appearance; is of convenient use and high performance. The door is a hollow glass door. There is a pilot lamp in the cabinet. The appliance is suitable for drinks and fruit storage. These instructions for use are intended for the user. They describe the appliance and correct operating procedures for safe use. Read and follow all safety rules and operating instructions before first use of this product. Save these instructions.
Installation and Safety Rules
-
It might cause vibration or noise due to uneven base. Please place the chiller on the even and hard floor.
-
Place the chiller in a dry regularly ventilated room, in order to increase chiller efficiency and reduce energy consumption. Therefore, ample space around chiller should be saving. The rear wall of the appliance should be at least 1 00m m from the wall. The two sides should be at least 200m m away from the wall. The tabletop should be at least 300m m away from the ceiling.
-
The chiller should be away from hot sources or direct sunshine.
-
The appliance should be placed on a solid base and away from heavy moisture place. If locate the appliance in wet place, it might affect electricity insulation and become rusty. If electrical parts are splashed with water, it might cause electricity leakage or breakdown.
-
Power supply:
The appliance befit for the single-phase alternating power supply with the voltage of 187V~ 242V, and the frequency of (50±1)HZ. -
Plug:
It is better to use an individual socket. It is dangerous to use multiple sockets. The plug must be plugged into an appropriately grounded wall socket. -
Avoid water splashing. If electrical parts are splashed with water, it might cause electricity leakage or breakdown.
-
Be sure not to put inflammable objects into the chiller; such as gasoline, propane, adhesive, and so on.
-
Never turn it over when you want to move the chiller. The obliquity of the chiller should be over 45°.
Operation Guide
-
Since the temperature is nearly the same as the ambient temperature when the appliance operates for the first time. In generally, it takes 2 hours to enable the tern perature inside to reach such one, which can stop motor running automatically.
-
After working for 2 hours with the reference of the following instructions, adjust the tern perature control to a suitable position and close the door, then the appliance can come to normal work. (Thermostat controls compressor to stop and start automatically.) Now, you can store beverages in it.
( NOTE: This table is for the reference of adjusting the temperature of the chiller when it is operated for the first time only.)
-
Be sure not to store any beverages in it before it comes to work normally.
Temperature Control
The tern perature control is fixed on the veneer or on the tabletop of the chiller. As shown in figure:
- For DFZ-368SCCG, when the control knob is in “Q” position the compressor does not operate.
- For DFZ-368SCCG , the tern perature control is adjusted from “1” to “7”, the tern perature in the cabinet is from high to low. That is to say, when turning to “1 “, tern perature is not too low; while turning to “4” or “7”, the tern perature is the lowest.
- If quick-freeze is required,” set the control knob to “5” – “7” (DFZ- 368SCCG ) . It should be turned back to other position. This is just for emergency use. Therefore, don’t use it frequently. Its continuous working time cannot be too long, or the tern perature in the cabinet might be so low that the bottles in the cabinet may be easily broken.
Defrost
After the chiller working for some time, frost will form on the surface of the evaporator. The thicker the frost is, the more hot resistance is. The hot resistance will reduce the effect of the refrigerant. Please defrost, when the frost is thicker than 5MM.
- Please set the control knob to “O” or disconnect the power supply before defrost the chiller.
- Open the door, and take out the food. Knock the frost gently. Wait until the defrost water is drained. Please clean with soft cloth dipping with warm water or neutral soap liquid. Be sure to wipe with pure water after using neutral soap liquid.
- Never attempt to scrape/remove ice /frost with sharp objects (such as knives, shovels, etc.). Or the evaporator will be broken down.
- After defrosting, connect the chiller to the power supply.
Trouble Shooting Guide
Sometimes you may come cross minor problems that are most cases do not require a service call and can be easily eliminated. The problem may have resulted from improper handling and/or installation of the appliance. Please refer to the below trouble-shooting guide to assist you in identifying the problem still persist after completing these checkpoints, contact the closest authorize service agent in your area for assistance.
DISTRIBUTED BY:
DAEWOO ELECTRONICS SALES & SERVICES (M) SDN BHD
LOT 886, BAY B2-B4, JALAN SUBANG 9,
TAMAN PERINDUSTRIAN SUBANG,
OFF JALAN PUCHONG HICOM,
47500 SUBANG JAYA, SELANGOR, MALAYSIA.