DAEMA DW-1498HC Washing Machine User Manual

DAEMA DW-1498HC Washing Machine

Safety Precaution

Be sure to completely with the following to prevent damage to your body, properly or others:

• The sign stands for “pay attention’, and the picture of specific items needs attention shows in
• The sign stands for “Forbidden”, and the picture of specific items forbidden shows in.
• The sign stands for “must do”, and the picture of specific items must be done showws in.

Installation

Attention To Installation

Lay upper drain hose

• Needs a drain hose with minimum diameter of 3 cm, and minimum carry away capacity of 40 liters per minute.
• For upper drain system, the drain hose must be placed at least 86 cm(30 inches) from the bottom of washer, but not higher than 100 cm.

FOR UPPER DRAIN SYSTEM ONLY

Change the position of the drain hose

The ex-factory installation position of the drain hose is located at the spin side. According to the installation site, the drain hose can also be installed at the wash side of the machine. The method is follows:

1. Unplug the power cord and empty water in the drain hose completely.
2. Spread piece of soft cloth on the floor (e.g. a blanket) and place the washing machine on it gently.
3. Take the drain hose out from the buckle at the spin side, and put it into the buckle at the wash side.
4. Hang up the drain hose kit.

FOR LOWER DRAIN SYSTEM ONLY

Installation site

In order to avoid electrical failure, discoloration and deformation, do not install the machine in the following places:

• Locations exposed to direct sunlight
• Locations exposed to rain
• Locations with uneven or unstable ground or show

Usage method

Preparation Instructions

• Plug in power and connect the water inlet hose.
• Lay down the lower drain hose and connect it to the sewer, or lay the upper drain hose to places as indicated in page 2.
• Check that there are no objects such as coins, hairpins, mud or sand in the pocket
• Strings should be knotted in advance to prevent entanglement.
• Clothes can be classified for washing according to the texture, dirty degree and color.
• For small pieces (e.9.stockings) or fluffy clothes, put them into a nylon net for washing.

Attachment: Reference of laundry quantity corresponding to different capacities

• The figure above is for reference only, specific weights are subject to actual clothes.

Attachment : Laundry volume and detergent dosage reference

• The dosage of washing detergent varies according to dirty degree and texture of laundries.

Structure Instruction

Name Of Parts

Accessories

Introduction Of Control Panel

The drawing above is for reference only, specific drawing is subject to actual models.

• Water inlet: be used to inject water.
• Wash time: be used to select required washing time.
• Spin time: be used to select required spinning time.
• Wash-Drain selector: For washing or rinsing, select ” Normal’or” Gentle”. For Draining ,select “Drain'”.

Usage method

Quick Start

Washing Method

1. Insert the water inlet hose into the water inlet mouth and choose injecting water to the wash tub.

2. Put the laundry into the wash tub, and add detergent into it.
   When fill water to half of the desired water level, turn off the water tap and let laundries soak in the solution for minutes, then fill water to desired water leve.

3. Set wash program “Normal” or “Gentle” as per amount and texture of laundries.

4. Turn the wash timer knob to set wash time.

5. After washing, set the wash drain selector to “Drain” position for draining.

Rinsing Method

A. Spraying rinse (rinse in the spin tub)

1. Put the laundry into the spin tub after washing
2. Turn on the water tap, choose to fill water into the spin tub for 3-4 minutes, and then turn off the water tap.
3. Set the spin timer for 2-6 minutes tor rinsing.
4. The above steps can be repeated.

Note: If there is red rust in water, do not choose spraying rinse, for the rust is easy to adhere to laundries.

Ensure that do not fill water into spin tub when spinning.

B. Common rinse (rinse in the wash tub)

1. To savetime, water and energy, can do pre-spinning before rinsing.
2. Put laundries which have already been dehydrated into the wash tub
3. After filing water to the desired level, turn off the water tap to save water.
4. Turn the “Wash selector knob to the “Normal” or “Gentle”
5. Set the “wash timer’to the desired time (about 3-5 minutes)for rinsing.
6. After rinsing, put the washing materials into the spin tub to spin for 1 to 5 minutes.
7. Drain out the rinsing water in the wash tub.
8. The above steps can be repeated.

Spinning Method

1. Shake out the laundry and put them into the spin tub.

2. Put the inner spin cover on the laundry.
   Confirm the inner spin cover is placed horizontally.

3. Close the safety cover and the spin cover.

4. Refer to the following table to select spinning time.

• The appliance can not be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction.
• The new hose supplied with the appliance are to be used and that old hose should not be used. when choose to inject water to wash tub or spin tub, water injecting is forbidden.
• lt strong vibration occurs in time of spinning, open the spin cover immediately. Make sure that the washing machine Is placed on a flat and stable floor ,and then adjust washing materials, distribute them evenly.
• To do spinning and training togetner, pliease spin minute error training.
• Do not wash or spin waterproof clotnes or clothes that fioat easly to avoid abnormal Vibration or damage to the clothes.

Efficiency Program (For efficiency program only
“Normal’wash, 15minutes with 40 C warm water, spin twice, 3minutes each: Rinse once for 5minutes with 20°C cold water, spin twice,3minutes each: Rinse once for 5minutes with 20C cold water, spin twice,4minutes each Water level “H’used for all wash and rinse.

Main Technical Parameters

Maintenance

Attention To Maintenance

Cabinet maintenance
After using the washing machine,wipe the moisture and stain on it with a piece of soft cloth. To avoid damage to the surface,do not use corrosive or volatile chemicals.

Cleaning the lint filter

• Press the button head, and pull the lint filter out.
• Turn the filter net inside out, and rinse it in water
• After inserting the claw, press the button to insert it into place.
• A sound of “ba” means proper installation.

Anti-freezing protection

To prevent from freezing:

1. Turn off the water tap, remove the water inlet hose and empty water in the water inlet hose completely.
2. Lay the drain hose and turn the drain selector knob to the “Drain'”position to empty the water in the tub.

If the water is frozen, please take the following steps:

1. Put the water inlet hose into warm water of about 50’C.
2. Keep about 2 liters of warm water below 50 C in the wash tub for about 10 minutes. and then lay the drain hose and turn the wash drain selector knob to the “Drain”position to empty the water.
3. Fit the water inlet hose and turn on the water tap to confirm water filling and draining work properly.

Operation when objects are dropped into the outside of the spin tub

1. Remove all screws on the frame with a screw driver and loosen the connector of the brake belt.
2. Pull up the frame with both hands and turn it backwards.
3. Take out the clothes dropped into the outside of the spin tub.
4. Fasten the connector of the brake belt,Press the frame to reset and tighten screws.

After you use the washing machine, never forget to do the following two things:

1. Disconnect the power plug.
2. Remove the water inlet hose.

Notes
The washing machine employs an alternative current with rated voltage and frequency. When voltage fluctuates between-10% and 10%% of the rated voltage, the machine can work normally. The connection mode of the power cord of this machine is a Y-shaped connection. Users should not detach or reconnect the wire by themselves.lf this part needs to be repaired, please contact the designated service center.

• Do not connect to the hot water supply.
• After using, be sure to unplug the power plug.
• Be sure to use plug that is properly grounded.
• The maximum gradient of the supporting surface for the washing machine should not exceed 2″.
• Do not tear down electrical wires and components in the machine by yourselft.
• There are holes on the base for ventilation. These holes should not be blocked by foreign objects (carpets, etc.).
• Never connect the grounding wire with the live wire, or it may lead to an electric shock.
• If the power cord is damaged, it must be replaced by a qualified person to avoid a hazard.

If the following symptoms occur, please disconnect the power plug and perform the following checks:

The installation manual of feet and holder

1. Open the carton,remove the foam base.
2. Take out feet and holders from washing machine
3. Lay the washing machine,install feet and holder accoring to the position of picture showing.
4. According to picture shown, insert foot into slot of the base,please note that the wheel toward to outside.
5. Insert holder into the corresponding position of base tighten the element by turning it clockwise until secure.

DAEWOO ELECTRONICS SALES & SERVICES (M) SDN BHD
Lot 886, Bay B2-B4, Jalan Subang 9,
Taman Perindustrian Subang,
Batu 14, Jalan Puchong-Hicom,
47500, Puchong, Selangor Darul Ehsan

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>