GRANNY 3813502 Electric preserving pot Instruction Manual
- June 3, 2024
- GRANNY
Table of Contents
GRANNY 3813502 Electric preserving pot
INSTRUCTIONS FOR USE
Dear customer, thank you for buying our product. Before putting the appliance into operation, read carefully these instructions for use and store properly this manual together with the certificate of warranty, a cash voucher and possibly with the package and the internal contents of the package.
SAFETY WARNINGS
-
Consider the instructions for use as a part of the appliance and pass them on to any other user of the appliance.
-
Do not insert or take the plug out of a socket with wet hands and do not pull the power cord!
-
This product can be used by children at the age of 8 years and older if they are supervised or if they were instructed regarding use of the appliance in a safe way and if they understand possible risks. Children must not play with the appliance. User cleaning and maintenance must not be performed by children if they are younger than 8 year and unsupervised. Children younger than 8 years must be kept out of reach of the appliance and its power cord.
-
The device may be used by persons with reduced physical or mental abilities or lack of experience and knowledge only if they are under supervision or they have been instructed about using the appliance safely and understand the potential dangers. Children must play with the appliance.
-
If the power cord of the appliance is corrupted, it has to be replaced by the manufacturer, its service technician or a similarly qualified person so as to prevent dangerous situations.
-
Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Return appliance to manufacturer or the nearest authorized service agent for examination, repair or electrical or mechanical adjustment.
-
Before replacing accessories or accessible parts, which move during operation, before assembly and disassembly, before cleaning or maintenance, turn off the appliance and disconnect it from the mains by pulling the power cord from the power socket!
-
CAUTION: Do not use the appliance with a program, time switch or any other part that turns the appliance on automatically as there is a risk of fire if the appliance is not covered or placed properly.
-
NOTICE: Some parts of this product may become very hot and cause burns. Take special care when children or handicapped persons are present.
-
Check whether the data on the type label correspond with the voltage in your socket.
-
The power cord plug has to be connected to a properly connected and grounded socket according to the EU standard.
-
Do not plug and unplug the electric socket plug with wet hands and do not pull the plug with the power cord!
-
The product is intended for home use and similar (in shops, offices and similar workplaces, in hotels, motels and other residential environments, in facilities providing accommodation with breakfast). It is not intended for commercial use!
-
When the appliance is in operation, prevent pets, plants or insects to get in contact with it.
-
Do not use the appliance with a timer or any other external part which turns the appliance on automatically – there is a risk of fire.
-
Do not immerse the appliance fully or partially to water! Do not wash under running water!
-
Use the appliance in the working position only at places with no risk of turning over and in sufficient distance from heat sources (e.g. heater, stove, cooker, oven, grill), flammable objects (e.g. curtains, drapes, etc.) and wet surfaces (e.g. sinks, wash basins, etc.).
-
Do not turn the appliance on empty, without water. Do not put more of liquid than marked on the container (MAX marks).
-
Do not use in the proximity of explosive materials, nor in places where there is a risk of explosion (e.g. gas stations etc.).
-
Use the appliance in areas with sufficient air circulation.
-
Do not use the appliance in places or in proximity of objects with extreme temperatures, excessive humidity or dustiness and in proximity of sources of magnetic field (e.g. credit cards). Protect it from direct sunlight.
-
The appliance is not designed for continuous operation!
-
Do not touch outer surfaces during operation of the kettle, they are hot and there is a risk of getting burned.
-
Do not move the appliance when hot; potential tipping over may result in burning injury.
-
It is not allowed to modify the surface of the appliance in any way (e.g. using a self adhesive wallpaper, foils, etc.)!
-
Do not leave any objects (e.g. protective gloves, kitchen towels) on the lid when the appliance is in operation as they could cover the steam escape openings.
-
Do not allow water, or food containing water, to freeze in the pot. It could damage the pot (crack it).
-
Do not place the appliance on unstable, fragile or flammable surfaces (e.g. glass, paper, plastic, wooden-varnished boards and various fabrics/tablecloths).
-
Use plastic or wooden kitchen utensils for stirring and scooping the food as metal utensils could damage the surface of the inner pot.
-
Use the appliance in the working position only in places where there is no risk of it being knocked over and at a sufficient distance from sources of heat (e.g. heaters, electric/ gas stoves, cookers, etc.) and wet surfaces (kitchen sinks, wash basins, etc.).
-
Do not use the appliance in an environment saturated with explosive or flammable steams.
-
Be careful when lifting the lid and always remove it in the direction away from yourself.
-
Use handles for carrying the appliance!
-
Prevent injuries when handling (e.g. by hot water, steam).
-
The bread maker conforms to fire safety requirements according to EN 60 335-2-6. Pursuant to this standard, this is an appliance that may be operated on a table or similar surface provided that: Safe distance from surfaces of flammable materials at least 500 mm in the direction of main heat radiation and 100 mm for other directions.
-
The appliance is equipped with the heat safety lock which disconnects power supply if water boils away or if an empty device is turned on.
If it happens, unplug the appliance from power supply and let it cool down. Do not fill the appliance with cold water in order to cool it down quickly. It could reduce life of the heating element. -
Use the pot only with the power cord that makes up its part! If the power cord is damaged, never replace it with a power cord that is not of the same type.
-
The appliance is portable and it is equipped with a movable connector with a plug, which ensures double-pole disconnection from power supply.
-
Check the condition of the power cord of the appliance regularly.
-
The power cord must not be damaged with sharp or hot objects, open fire and it must not be sunk into water.
-
Never put the power cord on hot surfaces or do not let it hang over the edge of a table or a work top. Plugging or pulling the power cord e.g. by children can result in tilting over or drawing the appliance down and serious injury!
-
If you need to use an extension cord, it has to be uncorrupted and it has to comply with the valid standards.
-
Use the appliance only with original accessories from the producer.
-
Use the appliance only for the purpose it is intended for as specified in this manual. Never use the appliance for any other purpose.
-
WARNING: There is a risk of injury in case of incorrect use (not in accordance with the manual) of the appliance.
-
The manufacturer is not responsible for damage caused by improper use of the appliance and the accessories (e.g. food deterioration, injury, burning, scalding, fire) and its guarantee for the appliance does not apply in situations when the safety warnings above are not complied with.
DESCRIPTION OF THE APPLIANCE AND ITS ACCESSORIES (Fig. 1)
A – Preserving pot
- A1 – release valve
- A2 – container of the pot
- A3 – heat-insulated handle
- A4 – lid
- A5 – removable grid
- A6 – supply cord
- A7 – thermal protection button
B – control panel
- B1 – I / O (ON/OFF switch)
- B2 – temperature regulator
- B3 – timer regulator (ON/OFF switch)
- B4 – operation light indicator
- B5 – signaling connection to the mains and KEEP WARM light indicator
PREPARATION AND USE
Remove all packaging material and remove the appliance with accessories.
Remove all adhesive foils, stickers or paper from the appliance. Wash all
parts, which will come in touch with food in hot water with soap, rinse them
thoroughly with clean water and wipe dry or let dry before first use. Make
sure that the power supply cord is not damaged and that it is not led
underneath the appliance or over any sharp or hot surfaces. The socket must be
readily accessible so that the appliance could be easily disconnected from the
mains in case of danger. Pour clean drinking water into the appliance up to
about 6 liters. Connect the power cord plug A6 to the electrical socket. Press
the switch B1 to the position “I” (indicator B5 indicating connection to the
mains).
Set the temperature regulator B2 into “100“ position and the timer regulator
B3 into “ON” position (indicator B4 indicating heating). Wait until the water
reaches boiling point (the indication lamp B4 turns OFF, and the indication
lamp B5 will turn on) and let it boil for at least 10 minutes. Let the
appliance cool off and pour out the water. Potential short and moderate smoke
or smell is not a fault and a reason for taking the appliance back. Place the
appliance on a solid flat and dry surface (e.g. kitchen table), out of reach
of children. If you are going to use the appliance for preserving in jars,
insert the removable grid A5 and fill the container with sufficient volume of
water, depending on the character and amount of the prepared food. Plug the
fork of the power supply A6 in the el. plug. The preserving pot is now ready
for use. The operation of the ETA preserving pot is easy and consists of two
main control features. It is the temperature regulator B2 and timer regulator
B3. When finishing or discontinuing the heating process, turn off the
appliance by turning both of the regulators counter-clockwise into „OFF/°C”
position. Turn the switch B1 to position “O“
(indicators light will go off), and disconnect the power cord from the wall
socket.
Over-heating protection
The preserving pot is equipped with a safety heat switch which will disconnect
the heating body in case of insufficient or no amount of water. If water is
not added the preserving pot will automatically turn off and must be allowed
to cool. If the preserving pot does not work after having been connected to
the el. outlet, in the lower part press button A7.
Temperature setting
The appliance is equipped with an in-built thermostat, which enables you to
set the temperature from approx. 30 °C to 100 °C (boiling point) with ±8%
accuracy. When reaching the set temperature, it is automatically maintained
(depending on the setting of the timer).
Setting the timer
Timer regulator B3 can be used in two modes.
-
automatic mode “20 – 120”
The timer enables you to set time in the range of 20 – 120 minutes. To increase the time desired, turn the regulator clockwise. To decrease it, counter-clockwise. When the set time runs out, the appliance turns off and a signal (1 beep) will sound. -
mode of continuous operation “ON”
In this mode, the heating is not time limited. It is suitable for heating food, which needs to be kept at a certain temperature longer than 120 minutes. You can set the mode by turning the regulator counter-clockwise into the “ON”. Do not turn the appliance on without water. Do not leave the appliance running unattended and keep an eye on it throughout the entire food preparation process! -
mode “OFF” the timer is off.
NOTE
The appliance is equipped with a reached temperature indicator switch B1. If you turn it on (position “I”), the appliance will beep loudly to give you notice about the temperature being reached. This is good especially when you need to count down exact time of heating from the point when the pot reached the set temperature. You can thus avoid the time difference caused by time when the pot is only heating (the time to reach the set temperature is individual and depends on the volume of water, ambient temperature etc.)
The process of preserving in a few steps
- Insert the removable grid A5 on the bottom of the container.
- Put in the mason jars (see Tips).
- Fill the container A2 with the necessary volume of water.
- Put on the lid A4
- Plug the fork of the supply cord A6 into the el. outlet.
- Set the desired temperature of heating.
- Set the desired time.
CAUTION: The heating up time is not included in the preserving time.
The preserving time starts when the selected temperature has been reached.
When reaching the set temperature and only now set the desired time of
preservation with the hand knob B3.
The heating is fully automatic (it does not apply for the “ON” mode) and when
the set time runs out, the appliance turns off. Then move the temperature
regulator B2 into “°C” position and unplug the appliance from the outlet. Set
the timer regulator into “ON” position for continuous operation.
NOTE
- The indicator light B4 turns off and on during heating. This is the thermostat turning on, it is not a fault of the appliance.
- The liquid must be added into the appliance before turning it on.
- Make sure water does not boil out of the container during long-lasting heating!
- Do not overfill the container of the preserving pot, leave at least 4 cm of free space from the top end of the container.
- The outer part of the appliance warms up during the heating. Pay close attention and do not touch the hot spots.
- Use the container with a lid!
- Hot water may remain on the inner part of the lid! Be careful to prevent injuries (scalds or burns).
TIPS
The process of preservation is a traditional and proven method of keeping
food. The ETA preserving pot also offers other uses, such as cooking, heating,
preparing hot drinks (incl. mulled wine or punch), blanching of vegetables,
etc. Follow your experience and general rules for cooking/preserving. You may
find a few of them below.
- It is very important that the food prepared is clean Fruit and vegetable should be of good quality, ripe and thoroughly cleaned. Rinse and dry the food well.
- Green beans and peas lasts longer if you blanch it first.
- Thick, syrupy liquids must be heated slowly and stirred constantly to prevent from scorching.
- Jars, bottles and their lids need to be rinsed in hot water, adding a little soap.
- Wash with clean water and let dry.
- Leave the closings in clean water until you use them.
- Do not use worn and damaged sealing, lids, jars or bottles.
- Fill the containers up to 2 cm from the top. When preserving soft food (puree etc.), leave room 3-4 cm from the top.
- When making smoked goods, fill the jars only up to ¾ of their volume.
- Close and seal the jars with screw-on lids, spring fasteners or clips.
- Close the jars (bottles etc.) right after conservation.
- Always put the jars on the removable grid – this will ensure good circulation of the boiling water around the jars, resulting in faster heating.
- You can use jars (containers) of various sizes and dimensions in this pot.
- The jars must be immersed in water from 2/3 to ¾. Immerse the biggest jar in ¾ (see pic). The jars which are fully immersed are sealed, that is why no water gets to them.
- Heating of the full volume of the pot may take up to 1.5 hours, it is therefore more efficient and faster to preserve “in steam”. Pour approx. 5-10 cm of water into the pot, this volume will heat up faster and the steam created will preserve with up to 60 %energy savings.
- The temperature of water poured into the container should be approximately the same as the temperature inside of the jars.
- Look up the temperature and time for preservation in your recipes, possibly other books about preservation.
- Preserving starts only when the set temperature is reached.
- Take out the jars when the time needed for preservation is up.
- Store the preserved food in a cool, dark place.
- It is good to write the date of preservation and their contents on the jars.
- The position of the thermostat can not be changed once the timer has been set, the count-down could be interrupted. If you have to change the temperature during the heating process, set the timer to the “OFF” position. Only now set the new temperature and the new time.
PRESERVATION TABLE
Fruit| Temperature
(oC)
| Time
(min)
| Vegetable| Temperature
(oC)
| Time
(min)
---|---|---|---|---|---
currant| 85| 20| cauliflower| 100| 90
puree| 90| 30| bean pods| 100| 120
pears| 90| 30| thick beans| 100| 90
strawberries| 75| 25| peas| 100| 120
blueberries| 85| 25| pickled vegetable| 90| 30
raspberries| 80| 30| carrot (small)| 100| 90
cherries| 80| 30| carrot| 100| 90
mirabelle| 90| 30| turnip| 100| 90
peaches| 90| 30| pumpkins| 90| 30
apricots| 90| 30| brussels sprouts| 100| 120
rhubarb| 100| 30| asparagus| 100| 120
gooseberry| 80| 30| kale| 100| 120
plums| 90| 30| tomatoes| 90| 30
apples| 90| 30| cucumbers| 100| 90
Meat| Temperature (°C)| Time (min)
---|---|---
roasted meat, pre-roasted| 100| 75
goulash| 100| 75
poultry, game, roast| 100| 75
schnitzel, chops, roast| 100| 75
smoked meat products| 100| 120
The times in the table are only approximate. The time before reaching the temperature is very individual and depends on multiple factors. The times in the table apply from the point of reaching the set temperature.
MAINTENANCE
Unplug the appliance from power supply by taking the connector of the power cord out of the socket before any maintenance! Clean the steam pot only after it has cooled down! Clean the appliance regularly after every use. Do not use rough and aggressive detergents (e.g. sharp objects, peelers, chemical solvents, thinning agents, caustic agents for cleaning ovens or other solvents)! Wipe the outer surface with a damp cloth with soap. Rinse the container from the inside and remove some possible sediments of limescale with a solution of citric acid or vinegar (then let boil with clean water). You can take apart the release valve A1 and clean separately. If you process thicker foods, we recommend closing the valve from the inside with a sealing cap to prevent excessive fouling. Never dry the plastic die-cast over a heat source (e.g. stove, el./gas cooker). If the power cord is soiled, wipe it with a wet cloth. It is common for the surface color to change in time. This change, however, does not have any influence on the surface characteristics in any way and it cannot be subject to a complaint under warranty!
Cleaning of grommet valve (fig. 1)
With one hand grip the tap and with the other hold the plastic nut on the
inside of the tank. Turn the tap anticlockwise to unscrew. The knurled cap at
the top of the tap can then be unscrewed to release the tap mechanism. Wash
all the other parts in hot water with a detergent, then rinse with clean water
and let them dry completely. In the reverse sequence insert the grommet into
the valve groove. In the reverse sequence assemble the individual parts in the
correct order and position (pull the valve tight with appropriate force).
CAUTION: Make sure that the bearing surfaces are clean and functional.
Storing
The appliance in a safe place. Store the appliance thoroughly clean on a dry,
dustless place out of reach of children and mentally disordered persons.
ENVIRONMENT
If the size of the appliance allows, all the parts contain marking of the materials used for production packaging, components and accessories as well as for recycling. The symbols on the product or in the accompanying documentation mean that the electrical or electronic product used must not be liquidated together with communal waste.
To ensure the appropriate liquidation take the used appliance to a collection
point where it will be accepted free of charge. Correct liquidation of the
product helps to protect valuable natural resources and helps to prevent a
potential negative impact on the environment and human health which can be the
outcome of inappropriate liquidation of waste. More details can be obtained
from your local authorities or the closest collection point. Inappropriate
manipulation of such waste can result in a fine according to the national
legislation.
Maintenance of a serious nature or maintenance which requires interference
with the internal parts of the appliance must be carried out by a professional
service centre! By failing to follow the instructions issued by the
manufacturer, the right to the warranty service will be invalidated!
TECHNICAL DATA
- Voltage (V)
- Wattage (W)
- Max. volume (l) Weight approx (kg)
- Protection class of the appliance
- Input in off mode is 0.00 W.
Shown on the type label of the appliance
Shown on the type label of the appliance
25 4.8 I.
The manufacturer reserves the right to change the technical specifications and
accessories for the respective models.
WARNINGS AND SYMBOLS USED ON THE APPLIANCE, PACKAGING OR IN THE INSTRUCTIONS
MANUAL
HOUSEHOLD USE ONLY. DO NOT IMMERSE IN WATER OR OTHER LIQUIDS
TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND
CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG
IS NOT
A TOY
References
- AEG Hausgeräte | Setzen Sie auf Qualität | AEG
- ElektroEko – Odbiór odpadów elektro
- ETA - tady je doma
- ETA - tu je doma