EuControls W902-DZB Zigbee and Bluetooth Certified AC Wall Dimmer Switch Instruction Manual

W902-DZB Zigbee and Bluetooth Certified AC Wall Dimmer Switch
Instruction Manual

W902-DZB Zigbee and Bluetooth Certified AC Wall Dimmer Switch

Momentary paddle buttons for on/off and dim up/down control
Control one or more remote lighting zone(s), depending on setup
Universal 120~277VAC input RGB status/locator LED| -ZB Connect wirelessly via Zigbee 3.0 or Autani EnergyCenter
-BT via Bluetooth or Autani EnergyCenter Neutral wire  required
Interchangeable white, beige, and black cover plates available
5 year limited product warranty
---|---

PRODUCT OVERVIEW

Introduction
W902-DZB is a Zigbee 3.0 while the W902-DBT is Bluetooth certified universal input120-277VAC dimmer switch designed for wall mount installation. The AC- powered dimmer switch allows for flexibility in control of one or more associated lighting zones, depending on setup.

Operation
After it is commissioned with a compatible gateway, the switch can be programmed to apply on/off control and step dimming to a remote fixture group. All aspects and sequence of operations are configurable via the associated gateway control software.

General Features
Wireless Electronic Control Dimmer Switch
Independently Mounted for Flush Mounting
Type of Action: Type 1 action
Pollution Degree: 2
Rated Impulse Voltage: 4000V
Operating Temp: 0⁰C to +40⁰C (+32⁰F to +104⁰F)
See below for Installation Instructions & Cautions.

Commissioning
All setup is performed via supported IEEE 802.15.4-based control platforms such as Autani EnergyCenter and other Zigbee 3.0 and Bluetooth compatible lighting control systems. Appropriate gateway control software allows for automated schedules, timers, and scenes.

Applications
This AC dimmer switch is designed for wall mount installation and is ideal for the following applications:

Location

FEATURE

• Momentary paddle buttons for on/off control and dim up/down control
• Dim and switch remote fixtures and fixture groups
• Configurable via gateway software for a wide range of installations and applications
• Zigbee 3.0 or Bluetooth certified and Autani
• EnergyCenter certified for easy setup and adjustment.
• AC-powered design removes need for batteries
• UV resistant, flame retardant, impact resistant, and recyclable polycarbonate construction

SPECIFICATION

• AC Input: 120~277VAC, 50/60Hz, 10mA Maximum
• User Controls: 2 momentary buttons for 4 total on/off and dim up/down operations, depending on duration of button press
• Radio Power: Zigbee Up to +20dBm transmit Bluetooth Up to +8dBm transmit
• Wireless Certification: Zigbee 3.0 or Bluetooth
•  Platform Certification: Autani EnergyCenter
• Operating Temperature: +32⁰F to +104⁰F (0⁰C to +40⁰C)
• Operating Humidity: 20% to 90% non-condensing
• Case Rating: IP20 for indoor use only Safety Certifications:
• E475915 UL/cUL Listed
• Regulatory Compliance: CE, RoHS, FCC, CA Title 24

PART NUMBER NOMENCLATURE

NOMENCLATURE: W902-DXXY
W902-DZB & W902-DBT

1. Basic Series Model Designation “W902”

2. Control (interface) Type “-DXX”
   Blank, One or more alphanumeric characters.
   As “-DZB” = Zigbee Wireless
   As “-DBT” = Bluetooth Wireless

3. Other “Y”
   Blank, One or more alphanumeric characters – Color,Packaging, Customer, or others for marketing purposes.

INSTALLATION

CAUTION
Risk of Electric Shock – Disconnect power source before servicing.
PRUDENCE
Risque de choc électrique – Débranchez la source d’alimentation avant l’entretien.

Wire: Strip 10mm (+1) insulation, connect or disconnect for field wiring.
For supply connector, use 14AWG wire rated for at least 75⁰C.
Use Copper Conductor Only.

compatible radio
W902-DBT| White| Universal voltage input wall mount dimmer switch with Bluetooth compatible radio

FCCID:
Bluetooth 2AJ2N-W902-DBT: Channel 0 to 39
Zigbee 2AJ2N-W902-DZB: Channel 11 to 25
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment  Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to  provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not  installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not  occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off  and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
  To maintain compliance with FCC’s RF exposure guidelines, the distance must be at least 20cm between the radiator and your body, and fully supported by the operating  and installation configurations of the transmitter and its antenna(s).
  This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this  device must accept any interference received, including interference that may cause undesired operation.

Copyright © 2021, EuControls Corp. All rights reser ved. Specifications subject to change without notice.
All product names, trademarks, and registered trademarks are property of their respective owners. W902-DXXY MKTG 20221018
PROPRIETARY & CONFIDENTIAL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>