PSL LM532675 Interior Smart Cob Lighting Kit Installation Guide
- June 3, 2024
- PSL
Table of Contents
PSL LM532675 Interior Smart Cob Lighting Kit Installation Guide
PACKAGE CONTENTS
4 x 24” COB LED Strips with Smart Hub
ACCESSORIES
TECHNICAL SPECIFICATIONS
Working voltage: DC 12V only
Types of LED:
144 x 0402 Red LED
144 x 0402 Green LED
144 x 0402 Blue LED
Watt: 8.5W
Maximum amperage: 0.7A
Replacement fuse: 2A
IP Rating of LED Strip: NA
Bluetooth distance: 30ft (no obstacle)
Frequency band: 2.4 GHz
INSTALLATION
Installing the LED strips:
-
Choose your desired location to install the light strips (Refer to the figure on the right for the recommended installing location for each LED strip and the Smart Hub.)
-
Clean the surface thoroughly with the alcohol pads provided and let it dry completely. Apply adhesion promoter to the same area.
-
Peel off the 3M™ tape backer at the bottom of the light strips and carefully apply to the desired area.
-
Secure the Smart Hub away from the car engine or any moving components. Make sure to avoid placing the Smart Hub or cables near any extremely HOT location or next to the car engine. Use 3M™ double-sided tape to secure all Smart Hubs to any flat location.
CONNECT TO POWER
Connecting the Smart Hubs to power:
Smart Hub hardwire cables are color coded, RED for POSITIVE (+) and BLACK for
NEGATIVE (-). Connect the RED cable to the POSITIVE (+) battery clamp as
illustrated. The POSITIVE battery post will be slightly larger than the
NEGATIVE post, and will be marked with a PLUS (+) sign. There may also be a
RED protective cover over the positive battery
post. Connect the BLACK cable to the NEGATIVE (-) battery clamp as
illustrated. The NEGATIVE will be marked with a MINUS (-) sign. There may also
be a BLACK plastic protective cover over the negative battery post.
NOTE: After connecting the Smart Hub to the car battery, the LED power indicator will flash Blue. If the LED power indicator does not flash once connected, please double check your power connections.
The Smart Hub has built-in voltage protection to prevent car battery from draining in case the lights are accidentally left on. The lights will be turned off automatically and the Smart Hub will be on standby mode when the voltage drops to approximately 12V. Once on standby mode, if the car battery is producing below 12V, do not turn on the LED lights until your next engine start or when the power is back to 12V or above.
WARNING: DO NOT mix up the cables or allow the metal ends to touch together because this may damage the battery, charging system and/or electronics on a vehicle. When installing, please make sure your engine is not running.
APP INSTALLATION
Install the TYPE S LED APP on your smart device. Scan below QR code or search for the TYPE S LED APP in the APP Store or Google Play. Once installed, open the APP and begin enjoying your TYPE S Pro Series Exterior Smart LED Kit!
Compatible with iPhone 4s & higher, iPad3, iPad Mini, iPad Air & higher, and iPod touch 5th Generation & higher. Requires iOS 9.0 or higher.
Compatible with phoneswith Android™ 4.3 or higher.
Note: not all Android™ phones are equipped with Bluetooth® v5.2 required for this application.
USING THE APP
Home Page
Tap “PRO SERIES” icon to start. The APP will automatically pair to the Smart Hub when both the lights and your device are powered on and within the 30-foot Bluetooth® range. We strongly recommend that you setup a private password to prevent unauthorized devices from connecting to the Smart Hub. (Refer to password instructions).
NOTE: The Smart Hub has built-in voltage protection to prevent car battery from draining in case the lights are accidentally left on. The lights will be turned off automatically and the Smart Hub will be on standby mode when the voltage drops to approximately 12V. Once on standby mode, if the car battery is producing below 12V, do not turn on the LED lights until your next engine start or when power is back to 12V or above.
Pro Series Page
A. Master On/Off Switch
B. LED Zone Functions
Zone On/Off: Press each zone icon to turn LED On or Off.
Move Zone Icon:
Press and hold the zone icon, select “Move” to position each zone icon at your
desired location.
Rename Zone Icon:
Press and hold the zone icon, select “Rename” to rename each icon.
(NOTE: Maximum 4 characters).
Select Multiple:
You can select and control multiple zones at a time. Press and hold the zone
icon, select “Select Multiple” then select your desired zones by pressing
“Confirm”. To ungroup your selection, press and hold the zone icon and select
“Ungroup”.
C. Preset Functions
Save Preset:
Save your favourite settings.
After choosing your settings, press “Save Preset” and enter your preset name.
Save up to 10 Presets.
Select Preset:
To select your previously saved preset setting, simply press “Select Preset”
and choose your saved setting.
Delete Saved Preset Setting:
To delete a saved preset setting, press “Select Preset”, press and hold the
preset you wish to delete. Press “Yes” to delete.
NOTE: Make sure the preset you wish to delete is not currently in use.
Select Color:
Choose from up to 49 different colors.
Press “Select Color”, select your desired color and press “Confirm”.
Password
D. Password
You can set up a password to prevent other devices from controlling your
lights. Once you have entered your password, it will be saved in the APP and
the Smart Hub.
NOTE: To set or change the password, your device must be connected to the
Smart Hub simply follow on-screen instructions. Changing the password without
connecting to the Smart Hub may cause an invalid password the next time your
APP and Smart Hub are activated.
If you forget your password, simply reset by pressing the Smart Hub’s reset
button for three seconds or disconnect the power from the car battery.
E. LED Modes
Choose up to 22 different modes including unique scan effects and Preset color
themes.
F. Brightness
Slide bar to adjust brightness setting.
G. Speed
Slide bar to adjust the speed of the movement from each LED mode
Music Mode
Sync lights with the beat of music
Music Mode allows music to control the lighting tempo through your smartphone or tablet. Sync lighting with your music in two ways: 1.) Through locally downloaded music files, or 2.) Through an enabled microphone on the smartphone / tablet.
Tap Local Music to choose music from your music library. Tap Microphone to activate your smartphone / tablet’s microphone; it will capture audio played from another source / device.
Due to copyright limitations, Music Mode is not available when playing audio from streaming services such as: Apple Music, Spotify, Pandora, YouTube, etc. Even if music files are saved to the smartphone or tablet from a streaming service, Music Mode will not work. We will provide a TYPE S LED APP update if streaming service support is available in the future.
CAUTION: When using Music Mode, keep the engine running. Low voltage battery protection will be disabled while in Music Mode. Low voltage battery protection will be enabled once the TYPE S LED APP is manually closed or disconnected.
Important Safety Instructions:
- SAVE THESE INSTRUCTIONS – This manual contains important safety and operating instructions for LED Kit model LM532675.
- NEVER use the APP while operating your vehicle. Use the APP when vehicle is stationary only.
- Before using this LED Kit, read all instructions and cautionary markings to ensure the product is properly & safely installed.
- Do not expose LED Kit to rain, moisture, or snow.
- Use of an attachment not recommended or sold by the LED Kit manufacturer may result in a risk of fire, electric shock, or injury to persons.
- Do not operate with damaged cord.
- Do not disassemble LED Kit; take it to a qualified serviceperson when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.
- To reduce risk of electric shock, disconnect all power before attempting any maintenance or cleaning. Turning off the lights will not reduce this risk.
WARNING: Do not install or use product if it, in any way, impairs the
safe operation of your vehicle. Follow manufacturer’s instructions to ensure
the product is properly & safely installed. Neither the manufacturer nor the
reseller can be held responsible or liable for consequential, incidental, or
indirect damages to either person or property resulting from the installation
or improper use of this product. Check your state, provincial, or local laws
before installing.
This product is not DOT approved.
WARNINGS
FCC Compliance Statement:
This device comply with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or change to this equipment. Such modifications or change could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
WARNING: This product can expose you to chemicals including DEHP and
DINP, which are known to the State of
California to cause cancer and birth defects or other reproductive harm. For
more information go to
www.P65Warnings.ca.gov.
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Winplus Co. Ltd is under license. Other trademarks and trade names are those of their respective owners.
3M VHB™ is a trademark of 3M company.
Pro Series Interior Smart COB Lighting Kit
LM532675
Responsible Party:
TYPE S
2975 Red Hill Ave., Ste. 100,
Costa Mesa, CA 92626, U.S.A.
Tel: 1.866.294.9244
A Horizon Brands Company
2975 Red Hill Ave., Ste. 100, Costa Mesa,
CA 92626, U.S.A.
1.866.294.9244 | info@typesauto.com
©2021 TYPE S. All rights reserved.
www.typesauto.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>