SIEMENS SN23EI26CE Dishwasher User Guide
- June 3, 2024
- SIEMENS
Table of Contents
SIEMENS SN23EI26CE Dishwasher
Before using for the first time, read the operating instructions.
Setting up Home Connect
Tip: Connect your appliance to a mobile device. You can conveniently change all settings via the Home Connect app.
- Install the Home Connect app on your mobile device and follow the instructions.
- Scan the QR code using the Home Connect app.
Overview of water hardness settings
You can find an overview of the water hardness values that can be selected
here.
A table of country-specific units can be found in the instruction manual
.
Setting the water softening system
-
Press .
-
To open the basic settings, press for 3 seconds.
The display shows H:xx.
The display shows -
Press or repeatedly until the right water hardness has been set.
-
To save the settings, press for 3 seconds.
Programmed
The programme data has been measured in the laboratory according to European
standard EN 60436.
The consumption figures depend on the programmed and additional function
selected.
The runtime will change if the rinse aid system is switched off or rinse aid
needs to be added.
Adding special salt
To avoid damage to the appliance, only add special salt to the dispenser
for special salt just before the programmed starts.
- Unscrew the lid of the dispenser for special salt and remove.
- On initial start-up: Fill the dispenser right up with water.
- Add the special salt to the dispenser. The water in the dispenser is displaced and forced out. Never add detergent.
- Place the lid back on the dispenser and turn to close.
Adding rinse aid
-
Press the catch on the lid of the dispenser for rinse aid and lift .
-
Add rinse aid up to the max mark.
-
Close the lid of the dispenser for rinse aid.
The lid clicks into position.
Adding detergent
-
Add the detergent to the dry detergent dispenser.
-
Close the lid of the detergent dispenser.
The lid clicks into position.
How to use your appliance
-
Load the tableware.
Only clean tableware that is suitable for dish-washers. Remove large remnants of food from the tableware. Check that the spray arms can rotate freely. -
Add detergent.
-
Switch on the appliance .
-
Select the programmed.
-
Start the programmed
-
Remove the tableware at the end of the programmed.
-
To cancel the programmed, press for approx. 4 seconds.
The programmed is cancelled and ends after approx. 1 minute.
Cleaning filters
- After each wash check the filters for residue.
- Turn the coarse filter antilock-wise and re-move the filter system .
- Pull down the micro filter to re-move.
- Press the locking catches together and lift the coarse filter out .
Clean wastewater pump
-
Disconnect the appliance from the power supply.
-
Remove the filter system.
-
Scoop out any water.
-
Prize off the pump cover using a spoon and grip it by the crosspiece.
-
Lift the pump cover inwards at an angle and remove.
-
Remove any remnants of food and foreign bodies in the area of the impeller.
-
Insert the pump cover and press down .
The pump cover clicks into position. -
Install the filter system.
Troubleshooting
Fault
E:32-00 will light up al-ternately or indicator for water supply lights up.
Cause and troubleshooting
Supply hose is kinked.
- Install the supply hose without kinks.
Water tap is turned off.
- Turn on the water tap.
- Water tap
is jammed or furred up.
- Turn on the water tap.
The flow rate must be at least 10 l/min when the water sup-ply is open.
The filters in the water connection of the supply or Aqua Stop hose are blocked.
-
Switch off the appliance.
-
Pull out the mains plug.
-
Turn off the water tap.
-
Unscrew the water connection.
-
Remove the filter from the sup-ply hose
-
Clean the filter.
-
Re-insert the filter in the supply hose.
-
Screw the water connection back on.
-
Check the water connection for leaks.
-
Restore the power supply.
-
Switch the appliance on.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>