Hunter 19752 Xidane 3 Light 15 inch Alturas Gold Foyer Pendant Ceiling Light Instruction Manual
- June 3, 2024
- Hunter
Table of Contents
©2022 Hunter Fan
Co. ML259 r_022822
19752 Xidane 3 Light 15 inch Alturas Gold Foyer Pendant Ceiling Light
Instruction Manual
19752 Xidane 3 Light 15 inch Alturas Gold Foyer Pendant Ceiling Light
Here are the ools you’ll need to
complete your installation:
Ladder Screwdriver Pliers Wire Strippers
4 Light Foyer Lantern Pendant
Fixture weight ±2 lbs: 12.1 bs (5.5 kg)
Hardware Service Kit
| Part | Model | Finish |
|---|---|---|
| KE20501L24 | 19751 | Palm Gold |
| KE20501214 | 19752 | Brushed Nickel |
Glass
| Part | Model | Type |
|---|---|---|
| 19751 | Clear Glass | |
| KE28301147 | 19752 |
INSTALLATION INSTRUCTIONS
WARNING
- To avoid possible electrical shock, before installing your light fixture, disconnect the power by turning off the circuit breakers to the outlet boxassociated with the wall switch location.
- The lighting fixture must be grounded. If the ground wire for the installation site is not present,immediately STOP installation and consult a qualified electrician.
- All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring or in doubt, consult a qualified electrician.
READ AND SAVE THESE INSTRUCTIONS
These instructions are provided for your safety. It is very important that
they are read carefully and completely before beginning installation of the
lighting fixture.
PREPARING FOR INSTALLATION
Carefully remove all contents from the carton. Shut off the power at the
circuit breaker and completely remove the old fixture from the ceiling,
including the old mounting bracket. Remove the new mounting bracket assembly
from the bag. One end of the threaded post (D) should be attached to the
mounting bracket (A) with a hex nut (E) in place. The other end should have
the canopy loop (G) attached. Unscrew the canopy loop ring (H) from the canopy
loop (G). Depending on the placement of your junction box the position of
threaded post (D) may need to be adjusted to allow the canopy to be flush with
the ceiling. Determine this by lifting mounting bracket (A) up to the junction
box and place canopy (F) over the canopy loop (G), so that it is flush with
the ceiling. Adjust the position of threaded post (D) on the mounting bracket
(A) so that the canopy (F) covers at least half of the exterior threads on the
canopy loop (G) while it is securely connected to threaded post (D). The
threaded post (D) can be adjusted by loosening hex nut (E) to allow movement
of threaded post (D) on mounting bracket (A). Once the ideal position of the
threaded post (D) is determined, tighten up the hex nuts (E) onto the threaded
post (D) just beneath the mounting bracket (A) to secure the threaded post in
place.
ASSEMBLING THE FIXTURE
Thread wires through the center rod (M) and attach it to the threaded post on
the fixture (N). Thread wires through the center of top ring (L) and connect
center rod (M) to swivel (U). Thread wires through and then tighten the
hanging ring (K) to the threaded post on top ring (L). Screw the three rods
(P) to the bottom ring (Q). Line rods (P) up with the holes on top ring (L)
and secure with screws (R). Set the glass shades (S) over the sockets and
secure with socket ring (T). By measuring, determine the correct number of
chain links needed for proper hanging height. If necessary, use a pair of
pliers to open and remove any excess chain. Attach one quick-connect link (J)
to each end of chain (I). Use one quickconnect link (J) to attach chain (I) to
hanging ring (K) and securely close. Feed the fixture wires up through the
chain (every three links or so), pulling the wires until taut. Slide canopy
loop ring (H) and canopy (F) onto the chain/wire and thread wires through
canopy loop (G). Use the remaining quick-connect link
(J) to attach chain (I) to canopy loop (G). To shorten the fixture, trim the
wires to desired length. Leave at least 8 to 10 inches of wire in addition to
the desired length. Have a helper support the fixture’s weight and attach the
mounting bracket (A) to the junction box by securely tightening the mounting
screws (C). 
CONNECTING THE WIRES
Attach the fixture’s wires to the power supply wires from the junction box.
Connect black to black (Live); white to white (grounded); grounding to
grounding (green or copper). Twist the ends of the wire pairs together. Then,
twist on a wire connector. Make sure all twists are in the same direction.
Loop fixture’s ground wire around grounding screw (B) and tighten. If there is
no ground wire (green or copper) from the junction box, contact a qualified
electrician.
FINISHING THE INSTALLATION
Place the canopy (F) flush to the ceiling and slide the canopy loop ring (H)
up beneath the canopy. Tightly screw canopy loop ring (H) onto the canopy loop
(G) to properly secure the canopy (F) in place. Attach finials (O) beneath
each socket. Install light bulb (not included) in accordance with the
fixture’s specifications. Do not exceed the recommended wattage. Your
installation is now completed. Turn on the power and test the fixture.
CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep
cleaning. For regular cleaning, turn off the light and wipe down the fixture
with a clean lint-free cotton or microfiber cloth. Never spray cleaner
directly onto the fixture.
Hunter Pro Tip:
Let the tool do the work! Use chain pliers to easily open and close chain
links to shorten your fixture.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>