EOGIFEE FAN-53T Small Size Universal Ceiling Fan Remote Control Instruction Manual
- June 3, 2024
- EOGIFEE
Table of Contents
FAN-53T Small Size Universal Ceiling Fan Remote Control
Instruction Manual
FAN-53T Small Size Universal Ceiling Fan Remote Control
SMALL SIZE REMOTE CONTROL
GENERAL INFORMATION
This remote controller is designed to separately control your ceiling fan
speed and light brightness. There are four buttons (HI, MED, LOW, OFF) to
control the speed of the fan and off. The light dimmer button will turn the
light on and off. The red indicator on the transmitter will light when one of
the five buttons is pressed.
INSTRUCTION OF INSTALLATION AND OPERATION
1. SETTING THE CODES
This unit has 16 different code combinations.
To set the codes. perform the following steps:
A. Setting the codes on the transmitter:
a. Remove battery cover. Press firmly on the arrow and slide battery cover
off.
b. Slide code switches to your choice of up or down position. Factory setting
is all up. Do not use this position. Use a small screwdriver or ball point pen
to slide firmly up or down (Figure 1).
B. Setting the codes on the receiver:
a. Slide code switches to the same position as set on your transmitter (Figure
2)
b. Replace battery cover on the transmitter.
2.INSTALLING RECEIVER IN CEILING FAN
A. Safety precautions:
WARNING: HIGH VOLTAGE! Disconnect power by removing fuse or switching off
circuit breaker.
Do not use with solid state fans.
Electrical wire must meet all local and national electrical code requirements.
Supply for fan must be 110/120 volt, 60Hz. Maximum fan motor amps: 1.0,
B. Installing receiver in fan:
a. Remove power from the circuit.
b. Remove ceiling fan canopy from the mounting bracket.
c. Disconnect existing wiring between ceiling fan and Supply in electrical
junction box.
d. Make connections as follows, using the wire nuts supplied:
NOTE:If you have PULL CHAINS SWITCH, before using the wireless remote
control, use the PULL CHAINS SWITCH to turn the wind speed to maximum and turn
the fan light on. Only in this way can the PULL CHAINS SWITCH and wireless
remote control be used together.
CAUTION: Ceiling angle
shall not exceed 30 Degrees, for mounting controller, Model Eogifee Small Size
Receiver.
CONNECT TO
Black wire(Live wire L)……Black supply wire
White wire(Neutral wire N)……….. White supply wire
Blue wire(To light live wire)…………… Blue light wire
White wire(To fan neutral wire N)………………. White fan wire
Black wire(To fan wire L)………………………………. Black fan wire
If other fans or supply wires
are different color, have this unit installed by qualified licensed
electrician.
e. Push all connected wires up into junction box.
f. Reinstall the canopy on the mounting bracket. g. Restore power.
3. OPERATING TRANSMITTER:(NOT INCLUDE 9 VOLT BATTERY)
A. Install 9 volt battery(not included). (To prevent damage to transmitter,
remove the battery if not used for a long time).
B. Store the transmitter away from excessive heat or humidity.
C. This remote control unit is equipped with 16 code combinations. In order to
prevent possible interference from or to other remote units such as garage
door openers, car alarm or security system. If you find that your fan and
light kit go on and off without using your remote control, simply change the
code combination in your transmitter and receiver.
D. Operating the buttons on the panel of the transmitter.
HI key -for fan high speed.
MED key-for fan medium speed.
LOW key-for fan low speed.
OFF key-for fan off.
FCC Statement:
This device is in conformance with Part 15 of the FCC Rules and Regulations
for Information Technology Equipment. Operation of this product is subject to
the following two conditions:
This device may not cause harmful interference, and (2) this device must
accept any interference received. including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party resp void the
use’ s authority to operate the equipment.
YOUR REMOTE NOW HAS FULL CONTROL OF THE FAN AND LIGHT.
“Optional Wall Mounting for Transmitter Holder”
Place in accessible area of your home, and screw the transmitter holder into
wall using the two screws provided, slide hand unit into holder.
The first step:lock the hook with two screws in the wall. The second
step:place the remote control on the hook
TROUBLE SHOOTING GUIDE
-
Fails to operate
a. Power to receiver ?
b. Receiver wired correctly ?
c. Fan manual speed control in highest position ?
d. Good battery in the transmitter ?
e. Code set at exact same positions in both transmitter and receiver ? -
Won’ t operate at distance
If transmitter operates fan/light kit when up close, but not at 20 feet away.
NOTICE! Your ceiling fan and light kit assembly must meet the following requirements:
- Do not use with solid state fans.
- Electrical rating: 120v 60Hz 3.5A MAX. Motor amps: 1.0
WARNING TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED WITH A WALL CONTROL/SWITCH.