SWIFT STL524B Desktop Label Printer User Manual

June 3, 2024
Swift

STL524B Desktop Label Printer
User’s ManualSWIFT STL524B Desktop Label Printer

STL524B Desktop Label Printer

NOTICE
Please read this manual carefully before using the printer!
Notice of Safety
Be sure to use the power supply provided by our company. Otherwise it may cause damage to the product.
Please do not open the paper case cover when it is printing or just when printing is finished, do not touch the printer head with hand or any part of body to avoid excessive temperatures leading to burns.
Notice of Using
Do not print the receipt with over 1m length. as this may damage the printer core.
Do not immerse the printer in water, or expose it to rain, as this can cause damage to the printer.
Do not open the paper case cover when it is printing, otherwise the printer may work improperly.
If printer is using USB connection to work, should not unplug the USB cable, or else some printing data may be lost. When printer is using Bluetooth connection to work, the distance of communication should be within 10 meters, otherwise the printer doesn’t print or prints rubbish codes.
Although the printer can work steadily when the environment temperature is between 0℃ to 50℃, too high(45℃)or too low(5℃) environment temperature and too high (above 85% relative humidity) or too low (below 20% relative humidity) environment humidity both effect the printing quality
The printer paper roll with poor quality or stored for too long time also may result in poor print quality even damage the printer.
Under the black mark detecting mode, the printer requires that the pre-printed black mark is accordant with the printing rule of black mark (please refer to details in Chapter 4.2), otherwise the black mark can not be detected correctly.
When the printer prints label paper, label should not over the maximum of the printer,
Notice of Storing
The printer should be stored at a temperature of -20 ° C to 60 ° C and a relative humidity of 10% to 90%.
Declaration
It is A class product, which may cause radio interference in the living environment. In this situation, users need to take feasible and effective measures to interfere with it.

Chapter 1 Outer Appearance and Model No.

1.1 Outer AppearanceSWIFT STL524B Desktop Label Printer - Outer
AppearanceSWIFT STL524B Desktop Label
Printer - Outer Appearance 3

STL524B Outer AppearanceSWIFT STL524B Desktop Label Printer - Outer
Appearance2 STL524B Outer Appearance

1.2 Model Name

Model Description Printing Density
STL524B USB, Blue Tooth 8dots/mm, 384dots/line

Chapter 2 Performance Characteristics

2.1 Printing Specification

Paper Width: Thermal line
Printing Width: 25mm(Min)—60mm(Max)
Max Label: 48mm/56mm(Max)
Min Label: 60x65mm
Label Gap: 25x20mm
Resolution: 2-3mm
Printing Method: 8dots/mm(203dpi)
Printing Speed: Label Paper 100mm/s(Max) Thermal Paper Max 127mm/s

2.2 Paper Roll

Paper Thickness:| Normal Thermal Paper: 0.06mm~0.08mm;
Label Paper: 0.12mm~0.14mm
---|---

2.3 Print Character
GB18030(Chinese) BIG5(traditional Chinese), GB12345(traditional Chinese), Shift+JIS(Japanese): 24×24 and 16×16 dot matrix ASCII: 12×24, 8×16, and 9×17 dot matri;x
International character set and Code page: 12×24 and 9×17 dot matrix; Self- defined character and figure; Barcode:
1D:UPCA,UPCE,EAN13,EAN8,CODE39,ITF25,CODABAR,CODE93, CODE 128 2D: PDF417,QR CODE,DATA Matrix
2.4 Physical Parameters

Dimension (W×L×H): 160(L)X130(W)X115(H)mm
Physical Weight: 580g (excluding roll paper)
Paper Roll: ≤80mm
Interface: USB, Bluetooth

2.5 Environmental Parameters

Operating Temp: 0℃~50℃
Operating Humidity: 10%~80%
Storage Temp: -20℃~60℃
Storage Humidity: 10%~90%

2.6 Other Specification

  • Paper Loading Method: please refer to details in 3.1.1 Paper Roll Installation.

  • Black Mark Location: available(details please see 4.2 pre-printed black mark manual).

  • Printing Control Command: ESC/POS compatible command set, CPCL command set, TSC/TSCL command set.
    (Refer tofor details).

  • Power Supply: DV12V±5%, 2A.

Chapter 3 Operation Instruction

3.1 Operation steps
3.1.1 Paper loading

  1. Open the paper cover and remove the paper shaft

  2. Pass the paper shaft through the core of the paper roll, taking care that the thermal side of the paper is facing the print head.

  3. Put the paper roll with the paper shaft into the paper bin and insert it into the slot.
    Adjust the baffle to the proper position according to the paper width to make the paper slide smoothly, and the paper also will not swing freely during the printing process.

  4. When close the paper cover, keep the amount of label paper which left outside fewest. It can reduce the waste of the paper roll.

SWIFT STL524B Desktop Label Printer - Outer Appearance
4

3.2 Basic functions instructions
3.2.1 Turn on
Close the paper cover in the power off state, then turn on the power. The power indicator and error indicator flash alternately two times, the power indicator is always on,and the error indicator is off. The printer enters the normal working mode.
3.2.2 Self test
Close the paper case, press the 【FEED】 button, then turn on the power. At this time, the printer will immediately print out the self-test. Parameters in the self-test will be different for different models.
Self-test can detect whether the printer is working properly. If the self-test can be printed correctly, it means the printer works normal except for the interface of the host.
Otherwise it needs to be repaired. Self-test prints out parameters in fellow order: manufacturer name, printer model, software version, interface type, default value of printer parameters, 96 characters in ASSIC code, default code page content (language setting is English) or Chinese character library name ( The language is set to Chinese) and the barcode type.
3.2.3 Paper feed (manual paper feed)
Receipt paper mode: In the power-on state, put in the ordinary thermal paper, press the 【FEED】 button, the printer starts to feed the paper, release the 【FEED 】 button to stop the paper feeding; Label mode: In the power-on state, put in the thermal label paper, press the 【FEED】 key. The printer forwards the paper to find the label gap, and sends the label gap to the tear line position.
3.2.4 Hexadecimal printing
Follow the steps below to turn the printer into hex print mode.

  1. Open the paper cover;
  2. Press the 【FEED】 button to turn on the power. Wait for the power indicator and the error indicator to flash alternately, then close the paper cover.
  3. At this point, the following 3 lines of content are printed:
    Hexadecimal Dump
    To terminate hexadecimal dump, Press FEED button three times.
    It indicates that the printer enters hex mode. In this mode, all inputs will be printed as hexadecimal numbers. Each press of the 【FEED】key will feed a line of paper.
    Press 3 times in total, and it will print out “ Completed ”, which means exit hex print mode.

3.2.5 Printer parameter settings
There are two ways to set printer parameters:

  1. Use the setting tool on PC to set.
  2. Set by button, the specific operation methods are as follows:
    In the power off state, open the Paper Cover firstly, press the 【FEED】 button, then turn on the power. Release the 【FEED】 button after the power indicator and error indicator flash alternately. Press the 【FEED】button two times, then close the Paper Cover. The printer enters the parameter setting mode and prints out the first
    settable parameter and its current set value. Check Appendix A for detailed setup methods.
    To exit the parameter setting method, press the 【PAUSE 】 button and 【FEED】 button simultaneously, then release the 【PAUSE 】 button and the 【FEED】 button at the same time. The printer saves the set parameter values and exits the parameter setting mode to enter the normal working mode.
    If the printer is powered off directly, the set parameter values are not saved.

3.2.6 Factory reset
In the power off state, open the Paper Cover firstly, press 【FEED】 button, then turn on the power. Release the 【FEED 】 button after the power indicator and error indicator flash alternately. Press the 【FEED】 button three times, then close the Paper Cover. The printer will print out the currently set parameters, and at the end prompt:
“Note: set the recovery system to the default values, press the 【FEED】 button to confirm. Direct power off cancel”. Press 【FEED】 button to confirm recovery, power off to cancel the factory reset Settings.
3.2.7 Printer calibration sensor sensitivity
In the power off state, open the Paper Cover firstly, press 【FEED】 button, then turn on the power. Release the 【FEED】 button after the power indicator and error indicator flash alternately. Press the 【FEED 】 button four times, then close the Paper Cover. The printer automatically performs the calibration function. If the calibration is successful, the printer will print out “Max Value”, “Min Value”, “Set Value” and “Sensor Level” in sequence. If the calibration fails, the printer will continue to feed 30cm. After the calibration is finished, the printer will restart.
3.2.8 Update Firmware

  1. Enter the
  2. Open“UpdateFirmware.exe”
  3. Choose the port, select the firmware file that needs to be upgraded, click “Start”, and wait until the data update is completed, the printer will automatically enter the upgrade mode.
  4. The 【POWER】 light and 【POWER 】light flash alternately. After the upgrade is completed, the printer automatically prints out the self-test and enters the normal
    working mode.

3.2.9 Switch mode of operation
In the power off state, open the paper cover, press 【FEED】button, turn on the power. Wait about 5 seconds, when the red error light flashes, release the 【FEED】 button, close the paper cover, the printer prints out ” Switch to ticket print mode” or “switch to label print mode”. (Depending on the current working mode of the printer, the printed information will be different). The printer will work in the prompted mode of operation.
3.3 Interface connection and printing
3.3.1 Power interface
The rated supply voltage is 12V ± 5% DC, rated current is 2A. Use a desktop power outlet, positive inside and negative outside. Please use the standard power adapter to supply power.
3.3.2 USB interface
The standard configuration of the STL524B printer is equipped with a standard USB printer cable B-port data cable for connecting the printer to the main device. The printer’s USB belongs to the slave device type (DEVICE); the outline and pin definitions are as follows:

SWIFT STL524B Desktop Label Printer - Outer Appearance
5

Pin No Function Notes
1 V Bus
2 Data – Data negative
3 Data + Date positive
4 GND Power ground

3.3.3 Bluetooth connection
A handheld device with Bluetooth interface, such as laptops, or other information terminals, can drive STL524B printing via the Bluetooth interface. The initial device name is “STL524B BT Printer” and the initial password is “1234”. Users can use to modify the device name and password as needed. For details on how to change the device name and password, refer to the help file of .
The STL524B printer must be paired with the Bluetooth master device that controls the printer before it works. Pairing is initiated by the master device.
The usual pairing process is as follows:

  1. Turn on the printer
  2. The master device searches for an external Bluetooth device.
  3. If there are multiple external Bluetooth devices, select STL524B BT Printer
  4. Enter the password “1234”
  5. Complete the pairing.
    For details on how to pair, please refer to the Bluetooth function description of the main device.
    Description: The STL524B printer supports connection with Android devices and Apple 4.0 devices.

Note:

  1. When pairing, the STL524B printer must be turned on.
  2. Once the printer’s Bluetooth device is successfully paired with the host Bluetooth device and a link is established, it will no longer provide search and link services to other primary Bluetooth devices until it is disconnected from the primary device that is linked to it.
Pin Signal Direction
1 Structural grand ——
2 Cash box drive signal Output
3 Cash box on/ofstatus signal input
4 +12V DC ——
5 NC ——
6 Signal ground ——

3.4 Indicator light, buzzer and button operation
The STL524B printer has two buttons, a built-in buzzer and two indicators.
【FEED】is the paper feed button. You can use the print command to enable or disable the button switch function. The button control mode is allowed: When in the ticket mode, press the 【FEED】button to output the paper, release the 【FEED】 button to stop the paper exiting. When in the label mode, press the 【FEED】 button, the printer advances the paper to find the label gap, and sends the label gap to the tear line position.
The buzzer is used to indicate the type of error status, which can be set to enable or disable the error alarm by parameter setting. The error status type is the same as the ERROR indicator.
The blue POWER indicator is the power indicator, and the POWER indicator is on to indicate that the printer is turned on.
The red ERROR indicator is an error status indicator. If the indicator is steady on, it indicates an error status. If the paper is out of paper, refer to the “Error Table” for details.
ERROR is a red indicator to remind the error status. When the printer is working normally, the red ERROR indicator is off. This indicator flashes to the abnormal alarm status. Error indication form:

Errors Error indicator status pecification
Without paper Constant on Replace the paper or use the appropriate label

stock
Paper case opens| Flash five timesstop 1 second| Close the paper case
Printer head| Flash one time,stop 1 second| Wait for a moment to continue printing

Chapter 4 Other Information

4.1 Development Manual
The STL524B Development Manual is a technical manual for the development of printer applications for STL524B printer users. This manual is available from the company.
4.2 Preprint black mark instructions
If the user uses the pre-printed black mark for ticket positioning, the following black mark pre-printing specifications must be observed when printing the black mark, otherwise the black mark may not be recognized by the printer. Black label pre-printing specification:

Printing position: As shown in the above figure, the black mark should be printed on the front left side and the back left side edge of the text side. Width range: width ≥ 7mm
Height range: 4mm ≤ height ≤ 6mm Reflectance to infrared light: <10% (reflectance of other parts of the paper black mark width for infrared light

65%) HPS: HPS is the distance from the edge of the printer black mark to the top edge of the print start. 4.5mm≤HPS≤6.5mm
4.3 Cleaning and maintenance
Power off,wipe the printing head with a cotton swab moistened with alcohol, to remove carbon deposit, dust and so on. Clear the paper scraps and dust of printing roller and cutter with dusting brush.SWIFT STL524B Desktop Label
Printer - Outer Appearance 8

Appendix A
Setting introduction: Press【PAUSE】 button to choose setting,when press it once , the set become the next one and it will print the present set value; use【FEED】button   o set the set value, when press it once , the set become the next one .After the setting is completed, press the [FEED] and [PAUSE] button at the same time to save  he current setting and enter the normal power-on state, otherwise the setting value will not be saved.
General Setting:SWIFT STL524B Desktop Label Printer - Outer Appearance
9

Print density:SWIFT STL524B Desktop Label Printer - Outer Appearance
11

Note: There are differences in speed setting items for different models. Please refer to the speed setting options of the actual model. **


Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals